Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2030EQ _54 Brake _014650 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0077110 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1246  Master Cylinder Pressure Sensor Malfunction  C1281  Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC)  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.

DTC C1281 is cleared when the Lost Booster Pressure Judgment Check is performed correctly in Test Mode and the check indicates a pass, or when Test Mode ends. DTC C1281 is output only in Test Mode.

C106656E33
3.927,4.115 5.552,4.313 1.625,0.198 10 Brake Actuator Assembly 2.896,1.344 4.042,1.531 1.146,0.188 10 Skid Control ECU 5.406,2.583 6.5,2.938 1.094,0.354 10 Master Cylinder Pressure Sensor 0.563,1.958 1.438,2.208 0.875,0.25 10 from Battery 0.26,2.625 1.344,2.969 1.083,0.344 10 from Stop Light Switch Assembly 0.354,3.375 1.396,3.604 1.042,0.229 10 to Body Ground 2.76,1.979 3.073,2.177 0.313,0.198 10 +BS 2.76,2.688 3.104,2.896 0.344,0.208 10 STP 2.76,3.396 3.135,3.594 0.375,0.198 10 GND 3.865,1.979 4.333,2.188 0.469,0.208 10 VCM 3.865,2.677 4.313,2.885 0.448,0.208 10 PMC 3.99,3.385 4.302,3.604 0.313,0.219 10 E2 0.542,4.76 3.958,4.969 3.417,0.208 10 VCM: Master Cylinder Pressure Sensor Power Supply 0.542,5.01 3.427,5.219 2.885,0.208 10 PMC: Master Cylinder Pressure Sensor Input 0.542,5.26 3.427,5.479 2.885,0.219 10 E2: Master Cylinder Pressure Sensor Ground

DTC No. Detection Item DTC Detection Condition Trouble Area
C1246 Master Cylinder Pressure Sensor Malfunction Any of the following is detected:
1.

The voltage of the sensor signal is out of range (below 0.129 V, above 3.29 V).

2.

An abnormality is detected in the skid control ECU internal sensor test.

3.

The sensor signal offset value is out of range.


·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder pressure sensor (Brake actuator assembly)


C1281 Master Cylinder Pressure Sensor Output Malfunction (Test Mode DTC) Detected only during Test Mode.
·

Stop light switch assembly

·

Brake pedal load sensing switch (Brake pedal support assembly)

·

Brake booster assembly

·

Master cylinder pressure sensor (Brake actuator assembly)



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. ON
Brake pedal released. OFF



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER PRESSURE SENSOR)

NG

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

2.READ VALUE USING INTELLIGENT TESTER (MASTER CYLINDER PRESSURE SENSOR)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Select the Data List using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Master Cylinder Sensor Master cylinder pressure sensor reading Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.20 to 0.40 V Reading increases when brake pedal is depressed
Chassis > ABS/VSC/TRC > Data List
Tester Display
Master Cylinder Sensor
50003 105 9

d.

Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the intelligent tester changes when the brake pedal is depressed.

OK:

When the pedal is depressed, the voltage displayed on the intelligent tester increases.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)

NG

3.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH)
a.

Select the Data List using the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch ON or OFF ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Stop Light SW
Brake Pedal Load Sensing SW
50003 105 37,39

b.

Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.

OK:

The intelligent tester displays on or off according to brake pedal operation.



c.

Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn on.

OK:

First the stop light switch should turn ON, and then the brake pedal load sensing switch should turn ON.



Result:
Result Proceed to
OK A
NG (The stop light switch does not turn on.) B
NG (Turning on of the brake pedal load sensing switch is not confirmed.) C
NG (The brake pedal load sensing switch turns on first.) D



A

4.RECONFIRM DTC

B

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

C

6.INSPECT BRAKE PEDAL LOAD SENSING SWITCH

D

8.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
4.RECONFIRM DTC
a.

Turn the ignition switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

At a speed of 30 km/h (18 mph) or more, drive the vehicle and perform a braking test (decelerate the vehicle by depressing the brake pedal).


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC C1246 is not output. A
DTC C1246 is output. B



A

B

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C238832C16
0.208,0.719 0.688,1.042 0.479,0.323 1.531,1.531 2.188,0.792 false 0.271,0.198 0.469,0.354 0.198,0.156 10 *a 0.344,0.802 0.917,1.125 0.573,0.323 10 A49 2.115,0.615 2.615,0.906 0.5,0.292 10 STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A49 skid control ECU connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*
A49-30 (STP) - Body ground Stop light switch OFF (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

6.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
a.
C239141C03
1.563,2.073 0.979,2.823 false 1.875,2.042 2.406,2.823 false 0.271,0.229 0.583,0.615 0.313,0.385 10 *a 0.688,2.875 1.146,3.063 0.458,0.188 10 FSW+ 2.25,2.875 2.708,3.063 0.458,0.188 10 FSW-
*a Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A40 brake pedal load sensing switch connector.

NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake pedal support assembly.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.




d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (FSW+) - 1 (FSW-) Switch OFF
(Brake pedal depressed)
950 to 1050 Ω
2 (FSW+) - 1 (FSW-) Switch ON
(Brake pedal released)
203 to 223 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)

B

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

C

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A49 skid control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-34 (FSW+) - A40-2 (FSW+) Always Below 1 Ω
A49-34 (FSW+) - Body ground Always 10 kΩ or higher
A40-1 (FSW-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation.

for LHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for LHD)>ADJUSTMENT

for RHD: Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL(for RHD)>ADJUSTMENT

OK:

The brake pedal height and stop light switch assembly installation are normal.



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

B

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

C

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

D

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY