The brake pedal load sensing switch turns on when the brake pedal is depressed with a force exceeding a predetermined level.
The skid control ECU uses this circuit to detect if the brake pedal is depressed or not.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1429 | Open or Short in Brake Pedal Load Sensing Switch | An open or short in the brake pedal load sensing switch circuit continues for 0.5 seconds or more. | ·
Brake pedal load sensing switch (Brake pedal support assembly) ·
Brake pedal load sensing switch circuit ·
Skid control ECU (Brake actuator assembly) |
When C1249, C1425 and/or C1426 is output together with C1429, inspect and repair the trouble areas indicated by C1249, C1425 and/or C1426 first.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1249
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1426
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch | ON or OFF | ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point |
- |
| Tester Display |
|---|
| Brake Pedal Load Sensing SW |
Check that the brake pedal load sensing switch display observed on the intelligent tester changes according to brake pedal operation.
The intelligent tester displays ON or OFF according to brake pedal operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Perform a road test.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1429 is not output. | A |
| DTC C1429 is output. | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *a | Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly)) |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A40 brake pedal load sensing switch connector.
Do not remove the brake pedal load sensing switch from the brake pedal support assembly.
When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 2 (FSW+) - 1 (FSW-) | Switch OFF
(Brake pedal depressed) |
950 to 1050 Ω |
| 2 (FSW+) - 1 (FSW-) | Switch ON
(Brake pedal released) |
203 to 223 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A49 skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-34 (FSW+) - A40-2 (FSW+) | Always | Below 1 Ω |
| A49-34 (FSW+) - Body ground | Always | 10 kΩ or higher |
| A40-1 (FSW-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG