The navigation ECU sub-assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
Using this circuit, the navigation ECU sub-assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the navigation ECU sub-assembly.
Disconnect the navigation ECU sub-assembly connector.
Disconnect the roof console box assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I67-4 (MACC) - S7-14 (MACC) | Always | Below 1 Ω |
| I67-5 (MIN+) - S7-13 (MCO+) | Always | Below 1 Ω |
| I67-19 (MIN-) - S7-12 (MCO-) | Always | Below 1 Ω |
| I67-6 (SNS2) - S7-15 (SNS2) | Always | Below 1 Ω |
| I67-4 (MACC) - Body ground | Always | 10 kΩ or higher |
| I67-5 (MIN+) - Body ground | Always | 10 kΩ or higher |
| I67-19 (MIN-) - Body ground | Always | 10 kΩ or higher |
| I67-18 (SGND) - Body ground | Always | 10 kΩ or higher |
| I67-6 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the navigation ECU sub-assembly connector.
Reconnect the roof console box assembly (telephone microphone assembly) connector.
| *a | Component with harness connected
(Navigation ECU Sub-assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I67-4 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I67-18 (SGND) - Body ground | Always | Below 1 Ω |
| I67-19 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the roof console box assembly (telephone microphone assembly) connector.
| *a | Component without harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S7-15 (SNS2) - S7-12 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the navigation ECU sub-assembly connector.
| *a | Component with harness connected
(Roof Console Box Assembly (Telephone Microphone Assembly)) |
Reconnect the roof console box assembly (telephone microphone assembly) connector.
Turn the ignition switch to ACC.
Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the roof console box assembly (telephone microphone assembly) connector.
Check the waveform of the telephone microphone assembly using the oscilloscope.
| Result | Proceed to |
|---|---|
| A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output | A |
| A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output | B |
A
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
B
Replace the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
Check if the same malfunction recurs.
| Result | Proceed to |
|---|---|
| Malfunction does not recur (returns to normal) | A |
| Malfunction recurs | B |
A
B