Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM › from 2015.04
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The Malfunction Indicator Lamp (MIL) is used to indicate vehicle malfunctions detected by the ECM. When the engine switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the engine switch is turned on (IG), the MIL should be illuminated and should then turn off after engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A348334E01
5.938,0.635 6.354,0.844 0.417,0.208 10 false IG2D 5.75,0.531 5.906,0.729 0.156,0.198 10 false 9 5.458,1.094 5.802,1.281 0.344,0.188 10 false A43 5.469,1.313 7.104,1.698 1.635,0.385 10 false Certification ECU (Smart Key ECU Assembly) 2.948,1.833 3.26,2.031 0.313,0.198 10 false 1C 3.083,2.052 3.24,2.25 0.156,0.198 10 false 8 3.771,2.292 4.083,2.49 0.313,0.198 10 false 1C 3.802,2.115 3.958,2.313 0.156,0.198 10 false 5 1.969,2.292 2.281,2.49 0.313,0.198 10 false 1D 2,2.115 2.156,2.313 0.156,0.198 10 false 3 1.948,2.781 2.26,2.979 0.313,0.198 10 false 1E 2,2.615 2.156,2.813 0.156,0.198 10 false 2 2.25,3.458 3.729,3.698 1.479,0.24 10 false No. 1 Integration Relay 4.177,2.49 4.979,2.75 0.802,0.26 10 false METER-IG2 5,2.281 5.271,2.51 0.271,0.229 10 false I18 5.01,2.094 5.323,2.292 0.313,0.198 10 false 13 5.302,2.167 5.583,2.365 0.281,0.198 10 false IG+ 5.99,2.177 6.323,2.375 0.333,0.198 10 false CHK 6.427,2.292 6.677,2.5 0.25,0.208 10 false I17 6.427,2.094 6.719,2.271 0.292,0.177 10 false 12 2.448,3.115 2.906,3.313 0.458,0.198 10 false IG2 0.885,2.448 1.635,2.688 0.75,0.24 10 false IG2-MAIN 0.583,3.51 1.198,3.74 0.615,0.229 10 false FL MAIN 0.75,4.563 1.292,4.823 0.542,0.26 10 false Battery 5.667,3.917 5.875,4.125 0.208,0.208 10 false 27 5.906,3.927 6.063,4.125 0.156,0.198 10 false W 5.99,4.979 6.323,5.198 0.333,0.219 10 false A25 6.313,4.99 6.771,5.188 0.458,0.198 10 false ECM 4.885,2.792 6.75,3.031 1.865,0.24 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.


Result:
Result Proceed to
MIL remains ON A
MIL does not illuminate B



A

2.CHECK WHETHER DTC OUTPUT RECURS

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 234

e.

Check if any DTCs have been detected. Note down any DTCs.

Result:
Result Proceed to
DTC is not output A
Any DTCs is output B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.




A

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

B

REPAIR CIRCUIT INDICATED BY OUTPUT DTC

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A255690C26
0.479,0.969 0.969,1.26 0.49,0.292 0.26,0.156 0.625,0.552 0.365,0.396 10 *a 0.615,1.031 0.969,1.333 0.354,0.302 10 A25
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-12 (CHK) or A25-27 (W) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the engine switch is turned on (IG).

OK:

MIL should be illuminated.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The GTS cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-12 (CHK) - A25-27 (W) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR