The skid control ECU receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.
If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U0123 (Lost Communication with Yaw Rate Sensor Module) is output. When U0123 is output together with C1234 and/or C1472, inspect and repair the trouble areas indicated by U0123 first.
DTCs may be stored if one of the following occurs:
Yaw rate and acceleration sensor circuit malfunction.
Yaw rate and acceleration sensor (airbag sensor assembly) installation abnormality.
Yaw rate and acceleration sensor signal malfunction.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1234 | Yaw Rate Sensor | Any of the following is detected:
1.
The yaw rate sensor offset value is estimated as less than -5.25 deg/s or more than 5.25 deg/s based on offset correction performed when the vehicle is stopped and then the vehicle starts off. 2.
The offset correction did not complete with the vehicle stopped, and the yaw rate sensor offset value is estimated as less than -15 deg/s or more than 15 deg/s based on the offset correction performed while the vehicle is being driven. 3.
The offset correction completed with the vehicle stopped and the yaw rate sensor offset value is less than -7.5 deg/s or more than 7.5 deg/s. 4.
The yaw rate sensor offset value is estimated as less than -7.5 deg/s or more than 7.5 deg/s based on the offset correction performed while the vehicle is being driven. 5.
After the VSC system has started, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 5 seconds or more when the vehicle is stopped. 6.
After the VSC system has started, but before the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more when the vehicle starts off. 7.
After the VSC system has started, but before the vehicle has started off, as the vehicle starts off, the yaw rate sensor value is less than -30 deg/s or more than 30 deg/s for 0.5 seconds or more. 8.
The yaw rate sensor value is less than -94.75 deg/s or more than 94.75 deg/s for 0.8 seconds or more. 9.
The change of the yaw rate sensor value within 0.04 seconds is abnormal. 10.
The value from the yaw rate sensor is judged as abnormal based on the skid control ECU estimation. |
·
Sensor installation ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
Yaw rate and acceleration sensor circuit |
| C1472 | Acceleration Sensor | Any of the following is detected:
1.
With the vehicle stopped, the internal acceleration value is less than -7 m/s2 or more than 7 m/s2 for 0.4 seconds or more. 2.
The acceleration sensor offset value is estimated as less than -2.25 m/s2 or more than 2.25 m/s2 based on the offset correction performed while the vehicle is being driven. 3.
The acceleration sensor value is less than -14.6 m/s2 or more than 14.6 m/s2 for 0.8 seconds or more. |
·
Sensor installation ·
Yaw rate and acceleration sensor (Airbag sensor assembly) ·
Yaw rate and acceleration sensor circuit |
When U0123 and/or U0126 is output together with C1234 and/or C1472, inspect and repair the trouble areas indicated by U0123 and/or U0126 first.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the engine switch off.
Start the engine.
At a speed of 30 km/h (18 mph) or more, drive the vehicle, turn the steering wheel, and decelerate (depress the brake pedal) the vehicle.
Turn the engine switch on (IG) again and check that no CAN communication system DTC is output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| CAN communication system DTC is not output. | A |
| CAN communication system DTC is output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the engine switch off.
Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
The ECU should be tightened to the specified torque.
The ECU should not be tilted.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION
| *a | Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly)) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the I47 yaw rate and acceleration sensor (airbag sensor assembly) connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I47-21 (IG2) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly)) |
Turn the engine switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I47-25 (E1) - Body ground | Always | Below 1 Ω |
| I47-26 (E2) - Body ground | Always | Below 1 Ω |
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG