While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).
While the engine is being cranked, current flows from terminal ST1 of the ignition or starter switch assembly to the park/neutral position switch assembly and also flows to terminal STA of the ECM (STA signal).
Refer to DTC P0617 (See page Engine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>P0617).
Inspect the fuses for circuits related to this system before performing the following procedure.
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Check if the engine can be cranked
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Connect the intelligent tester to DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Tester Display (Starter Signal) |
|---|---|
| ON | Close (Off) |
| START | Open (On) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST relay.
Click hereEngine / Hybrid System>2GR-FE STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter assembly.
Click hereEngine / Hybrid System>2GR-FE STARTING>STARTER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the engine room relay block and junction block assembly.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (ST relay) - E9-1 | Always | Below 1 Ω |
| 3 (ST relay) or E9-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) battery terminal - F2-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (ST relay) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Remove the ST relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E77-9 (L) - 2 (ST relay) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (w/o smart entry and start system) | A |
| OK (w/ smart entry and start system) | B |
| NG | C |
A
B
C
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>2GR-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition or starter switch assembly connector.
Remove the ST relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I36-7 (ST2) - 5 (ST relay) | Always | Below 1 Ω |
| I36-7 (ST2) or 5 (ST relay) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the park/neutral position switch assembly.
Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/o smart entry and start system) | A |
| OK (w/ smart entry and start system) | B |
| NG | C |
A
B
C
Click hereDrivetrain>U660E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Inspect the ignition or starter switch assembly.
Click hereEngine / Hybrid System>2GR-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition or starter switch assembly connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I36-3 (ST1) - E77-4 (B) | Always | Below 1 Ω |
| I36-3 (ST1) - E26-65 (NSW) | Always | Below 1 Ω |
| I36-3 (ST1) or E77-4 (B) or E26-65 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Remove the ST relay from the engine room relay block and junction block assembly.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E77-9 (L) - 2 (ST relay) | Always | Below 1 Ω |
| E77-9 (L) or 2 (ST relay) or A25-9 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A43-5 (STAR) - E77-4 (B) | Always | Below 1 Ω |
| A43-5 (STAR) - E26-65 (NSW) | Always | Below 1 Ω |
| A43-5 (STAR) or E77-4 (B) or E26-65 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Remove the ST relay from the engine room relay block and junction block assembly.
Disconnect the ECM connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E77-9 (L) - 2 (ST relay) | Always | Below 1 Ω |
| E77-9 (L) or 2 (ST relay) or A25-9 (STA) or A43-7 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Tester Display (Starter Signal) |
|---|---|
| ON | Close (Off) |
| START | Open (On) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG