Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM J

2AR-FXE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the start request signal output from the power management control ECU is input to the ECM, and the NE signal generated by the crankshaft position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input to the ECM with the engine running, the ECM turns Tr1 on continuously.

WIRING DIAGRAM

A276418E05
1.042,1.813 1.688,1.969 0.646,0.156 10 false IG2-MAIN 2.229,7.646 2.5,7.792 0.271,0.146 10 false N11 2.229,7.792 2.927,7.958 0.698,0.167 10 false Fuel pump 0.688,7.813 1.313,8.208 0.625,0.396 10 false Auxiliary Battery 3.021,7.156 4.646,7.438 1.625,0.281 10 false No. 1 Integration Relay 3.198,3.781 3.823,3.938 0.625,0.156 10 false EFI MAIN 3.156,5.094 3.875,5.25 0.719,0.156 10 false EFI MAIN2 0.813,3.229 1.854,3.385 1.042,0.156 10 false EFI-MAIN NO. 1 0.813,4.927 1.865,5.083 1.052,0.156 10 false EFI-MAIN NO. 2 2.417,1.656 2.615,1.813 0.198,0.156 10 false 1D 2.458,1.479 2.563,1.635 0.104,0.156 10 false 3 2.417,3.094 2.615,3.25 0.198,0.156 10 false 1B 2.469,2.917 2.573,3.073 0.104,0.156 10 false 1 2.417,3.469 2.615,3.625 0.198,0.156 10 false 1E 2.458,3.292 2.563,3.448 0.104,0.156 10 false 2 2.406,4.781 2.604,4.938 0.198,0.156 10 false 1D 2.448,4.594 2.552,4.75 0.104,0.156 10 false 1 2.417,5.854 2.615,6.01 0.198,0.156 10 false 1C 2.469,5.667 2.573,5.823 0.104,0.156 10 false 6 3.375,2.302 3.625,2.458 0.25,0.156 10 false IG2 3.292,6.604 3.75,6.76 0.458,0.156 10 false C/OPN 4.99,3.458 5.188,3.615 0.198,0.156 10 false 1C 5.042,3.292 5.146,3.448 0.104,0.156 10 false 7 5.938,6.729 6.146,6.885 0.208,0.156 10 false FC 5.677,6.729 5.854,6.885 0.177,0.156 10 false 21 5.938,3.469 6.344,3.625 0.406,0.156 10 false MREL 5.677,3.385 5.854,3.542 0.177,0.156 10 false 46 6.281,7.99 6.615,8.146 0.333,0.156 10 false ECM 5.938,7.99 6.281,8.198 0.344,0.208 10 false A25 4.448,1.417 4.646,1.573 0.198,0.156 10 false 1C 4.396,1.219 4.5,1.375 0.104,0.156 10 false 8 4.99,6.813 5.188,6.969 0.198,0.156 10 false 1E 5.042,6.656 5.146,6.813 0.104,0.156 10 false 1 1.958,7.323 2.063,7.479 0.104,0.156 10 false 4 1.958,8.26 2.063,8.417 0.104,0.156 10 false 5 1.958,8.052 2.083,8.208 0.125,0.156 10 false E 1.958,7.531 2.083,7.688 0.125,0.156 10 false B 5.75,0.458 5.854,0.615 0.104,0.156 10 false 2 5.938,0.542 6.281,0.698 0.344,0.156 10 false IG2D 5.771,1.156 6.042,1.313 0.271,0.156 10 false A39 5.771,1.323 7.063,1.646 1.292,0.323 10 false Power Management Control ECU 6.552,6.167 6.792,6.323 0.24,0.156 10 false Tr1 0.542,6.198 0.917,6.354 0.375,0.156 10 false MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the tester.


Result:
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B



A

2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

B

7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1E-1 - A25-21 (FC) Always Below 1 Ω
1E-1 or A25-21 (FC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-6 - N11-4 (B) Always Below 1 Ω
1C-6 or N11-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the fuel pump connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N11-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2AR-FXE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)

NG

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


A256530C08
0.719,1.094 1.083,1.365 0.365,0.271 0.188,0.115 0.448,0.271 0.26,0.156 10 false *a 0.813,1.156 1.135,1.323 0.323,0.167 10 false 1D
*a Front view of wire harness connector
(to No. 1 Integration Relay)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1D-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AUXILIARY BATTERY - NO. 1 INTEGRATION RELAY)

7.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

f.

Check the result when the power switch on (IG) and the engine starts.

OK:
Condition Starter Signal
Power switch on (IG) Close (OFF)
Engine started Open (ON)


Result:
Proceed to
OK
NG




OK

8.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

NG

8.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

f.

Read the values displayed on the tester while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

CHECK CRANKSHAFT POSITION SENSOR CIRCUIT