Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM C

2AR-FXE ENGINE CONTROL  SFI SYSTEM  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter sub-assembly is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine fuel injection duration and to provide an appropriate air fuel ratio.

Inside the mass air flow meter sub-assembly, there is a heated platinum wire which is exposed to the flow of intake air. By applying a specific electrical current to the wire, the ECM heats it to a specific temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A234789E05
4.865,1.313 4.26,2.125 false 2.49,1.073 2.292,1.469 false 5.125,1.542 5.448,2.125 false 1.448,0.281 1.969,1.438 false 2.25,0.563 3.323,0.719 1.073,0.156 10 Power Transistor 2.021,0.073 2.385,0.25 0.365,0.177 10 +B 2.531,0.979 4.229,1.135 1.698,0.156 10 Platinum Hot Wire (Heater) 2.938,1.583 3.896,1.74 0.958,0.156 10 Output Voltage 2.792,2.146 4.479,2.302 1.688,0.156 10 Platinum Hot Wire (Heater) 4.896,2.146 7,2.302 2.104,0.156 10 Temperature Sensor (Thermistor) 0.135,0.177 1.438,0.51 1.302,0.333 10 Temperature Sensor (Thermistor) 1.656,1.49 1.802,1.646 0.146,0.156 10 A 2.49,1.49 2.646,1.646 0.156,0.156 10 B

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0102 Mass or Volume Air Flow Circuit Low Input The mass air flow meter sub-assembly voltage is less than 0.2 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

No. 1 integration relay

·

ECM


Comes on DTC stored
P0103 Mass or Volume Air Flow Circuit High Input The mass air flow meter sub-assembly voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter sub-assembly circuit

·

Mass air flow meter sub-assembly

·

No. 1 integration relay

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the air flow rate using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.


Mass Air Flow Rate (gm/sec) Malfunction
Approximately 0.0
·

Open in mass air flow meter sub-assembly power source circuit

·

Open or short in VG circuit


271.0 or more
·

Open in E2G circuit



MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the mass air flow meter sub-assembly, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter sub-assembly circuit and stores a DTC.

Example:

When the sensor output voltage remains less than 0.2 V, or higher than 4.9 V for 3 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Wait 5 seconds or more.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC.

8.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0102 or P0103.

11.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A268313E07
2.563,0.927 3.219,1.083 0.656,0.156 10 false EFI NO. 3 3.781,1.969 4.385,2.25 0.604,0.281 10 false E14 3.781,2.115 5.083,2.5 1.302,0.385 10 false Mass Air Flow Meter Sub-assembly 0.656,2.51 1.25,3.083 0.594,0.573 10 false Auxiliary Battery 1.594,1.771 3.24,2.021 1.646,0.25 10 false No. 1 Integration Relay 1.927,1.417 2.583,1.573 0.656,0.156 10 false EFI MAIN 1.333,0.75 1.813,1.115 0.479,0.365 10 false 1B 1.385,0.573 1.49,0.729 0.104,0.156 10 false 1 1.417,1.552 1.76,1.917 0.344,0.365 10 false 1E 1.406,1.385 1.51,1.542 0.104,0.156 10 false 2 5.646,1.063 6.021,1.479 0.375,0.417 10 false E28 5.719,0.885 5.896,1.042 0.177,0.156 10 false 91 5.656,1.563 6.083,1.833 0.427,0.271 10 false E28 5.719,1.385 5.896,1.542 0.177,0.156 10 false 92 3.208,0.75 3.542,1.042 0.333,0.292 10 false 1A 3.26,0.573 3.365,0.729 0.104,0.156 10 false 8 5.927,2.615 6.448,2.833 0.521,0.219 10 false MREL 6.177,3.302 6.51,3.458 0.333,0.156 10 false ECM 3.875,0.656 4.156,0.896 0.281,0.24 10 false +B 3.688,0.656 3.792,0.813 0.104,0.156 10 false 3 6,0.979 6.219,1.135 0.219,0.156 10 false VG 6,1.479 6.292,1.635 0.292,0.156 10 false E2G 4.781,0.979 5,1.135 0.219,0.156 10 false VG 5.094,0.979 5.188,1.135 0.094,0.156 10 false 5 4.698,1.479 4.99,1.635 0.292,0.156 10 false E2G 5.094,1.479 5.188,1.635 0.094,0.156 10 false 4 5.375,2.052 5.469,2.208 0.094,0.156 10 false * 5.646,2.844 6.01,3.146 0.365,0.302 10 false A25 5.719,2.667 5.896,2.823 0.177,0.156 10 false 46 3,1.563 3.344,1.854 0.344,0.292 10 false 1C 3,1.396 3.104,1.552 0.104,0.156 10 false 7 0.563,0.896 1.208,1.323 0.646,0.427 10 false EFI-MAIN NO. 1 0.5,1.76 0.958,1.958 0.458,0.198 10 false MAIN 3.104,3.375 4.125,3.615 1.021,0.24 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (DTC P0102 OR P0103)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B




A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MASS AIR FLOW METER SUB-ASSEMBLY)
a.
A194097C28
0.281,2.021 0.667,2.281 0.385,0.26 1.698,2.458 1.24,3.042 true 0.177,0.073 0.375,0.25 0.198,0.177 10 false *a 1.083,3.073 1.458,3.292 0.375,0.219 10 false +B 0.344,2.073 0.656,2.281 0.313,0.208 10 false E14
*a Front view of wire harness connector
(to Mass Air Flow Meter Sub-assembly)


Disconnect the mass air flow meter sub-assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E14-3 (+B) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E14-5 (VG) - E28-91 (VG) Always Below 1 Ω
E14-4 (E2G) - E28-92 (E2G) Always Below 1 Ω
E14-5 (VG) or E28-91 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
a.

Inspect the mass air flow meter sub-assembly, referring to the On-vehicle Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION


b.

Inspect the mass air flow meter sub-assembly, referring to the Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION


c.

Inspect the function of the mass air flow meter sub-assembly.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the power switch on (IG).


iii.

Turn the tester on.


iv.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

v.

Start the engine.


vi.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
50003 234 3

vii.

Check that the MAF value changes when the engine is raced.

OK:

The reading changes.


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
OK
NG



OK

NG

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E14-3 (+B) - 1A-8 Always Below 1 Ω
E14-3 (+B) or 1A-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E14-4 (E2G) - Body ground Always Below 1 Ω


HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER SUB-ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
a.

Disconnect the mass air flow meter sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E14-4 (E2G) - E28-92 (E2G) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR