Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM C

2AR-FXE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV (Vacuum Switching Valve for purge control) so that the intake amount of hydrocarbon (HC) emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0443 Evaporative Emission Control System Purge Control Valve Circuit Both of the following conditions (a) and (b) are met (1 trip detection logic):
(a) The target control value and actual control value do not match for 10 seconds or more.
(b) The target control value and actual control value do not match for 80 times or more.
·

Open or short in purge VSV circuit

·

Purge VSV

·

No. 1 integration relay

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A179391E34
0.958,1.563 1.167,1.156 1.167,1.156 1.271,1.156 false 1.521,1.948 1.75,2.125 0.229,0.177 10 false [A] 2.844,1.948 3.073,2.125 0.229,0.177 10 false [B] 3.896,3 4.125,3.177 0.229,0.177 10 false [C] 4.573,1.333 4.802,1.51 0.229,0.177 10 false [D] 5.094,3 5.323,3.177 0.229,0.177 10 false [E] 0.51,2.073 0.885,2.26 0.375,0.188 10 false Idling 4.229,2.521 5.01,2.833 0.781,0.313 10 false 10 minutes or more 2.594,2.521 3.375,2.833 0.781,0.313 10 false 15 minutes or more 1.313,2.521 2.083,2.729 0.771,0.208 10 false Warming up 1.333,1.073 2.906,1.396 1.573,0.323 10 false Between 40 and 60 km/h 0.125,0.448 1.073,0.615 0.948,0.167 10 false Vehicle Speed

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

HINT:

The A/C switch and all accessory switches should be off.


8.

Idle the engine for 15 minutes or more [B].

HINT:

Check the EVAP (Purge) VSV item in the Data List. When the value of this item is between 5 and 95%, the judgment will be performed.


9.

Enter the following menus: Powertrain / Engine and ECT / DTC [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0443.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [D] and [E].



14.

Drive the vehicle at a constant speed between 40 and 60 km/h (25 and 37 mph) for 10 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


15.

Check the DTC judgment result again [E].


WIRING DIAGRAM

A268315E03
6.219,3.302 6.552,3.448 0.333,0.146 10 false ECM 5.75,0.969 6.083,1.115 0.333,0.146 10 false PRG 5.75,2.75 6.177,2.896 0.427,0.146 10 false MREL 5.417,2.844 5.688,3 0.271,0.156 10 false A25 5.448,2.667 5.625,2.823 0.177,0.156 10 false 46 5.417,1.063 5.688,1.219 0.271,0.156 10 false E28 5.458,0.885 5.635,1.042 0.177,0.156 10 false 68 4.125,1.563 4.854,1.74 0.729,0.177 10 false Purge VSV 4.125,1.385 4.479,1.542 0.354,0.156 10 false E49 5.021,0.958 5.135,1.104 0.115,0.146 10 false 2 3.875,0.958 3.99,1.104 0.115,0.146 10 false 1 3.198,0.76 3.406,0.917 0.208,0.156 10 false 1A 1.417,1.563 1.625,1.719 0.208,0.156 10 false 1E 1.344,0.75 1.552,0.906 0.208,0.156 10 false 1B 1.385,0.563 1.521,0.719 0.135,0.156 10 false 1 1.927,1.448 2.573,1.583 0.646,0.135 10 false EFI MAIN 0.531,0.917 1.177,1.26 0.646,0.344 10 false EFI-MAIN NO. 1 0.5,1.875 0.885,2.021 0.385,0.146 10 false MAIN 2.583,0.927 3.229,1.115 0.646,0.188 10 false EFI NO. 3 1.385,1.375 1.5,1.531 0.115,0.156 10 false 2 2.99,1.563 3.198,1.719 0.208,0.156 10 false 1C 2.979,1.375 3.094,1.531 0.115,0.156 10 false 7 3.229,0.583 3.365,0.74 0.135,0.156 10 false 8 0.677,2.51 1.229,2.844 0.552,0.333 10 false Auxiliary Battery 1.583,1.781 3.073,2.073 1.49,0.292 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A263312C01
1.799,0.144 1.948,0.302 0.149,0.158 10 *1 1.76,0.236 1.556,0.236 1.556,0.236 1.423,1.349 false 1.595,3.066 1.744,3.224 0.149,0.158 10 *2 1.797,3.147 2.001,3.147 2.001,3.147 2.16,1.82 false
*1 Purge VSV
*2 Fuel Vapor Feed Hose (to Canister)


Disconnect the fuel vapor feed hose (on the canister side) of the purge VSV.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the tester on.


e.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

f.

Start the engine.


g.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for EVAP Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

h.

Operate the purge VSV and check the air flow.

OK:
Activate the VSV for Evap Control Specified Condition
ON Air flows
OFF Air does not flow


Result:
Result Proceed to
Abnormal A
Normal B


HINT:

Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.




A

2.INSPECT PURGE VSV

B

2.INSPECT PURGE VSV

Result:
Proceed to
OK
NG



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)
a.
A194112C23
0.287,0.389 0.491,0.562 0.205,0.173 10 *a 0.584,2.213 0.86,2.355 0.276,0.142 10 E49 0.523,2.157 0.935,2.432 0.413,0.275
*a Front view of wire harness connector
(to Purge VSV)


Disconnect the purge VSV connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E49-1 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - NO. 1 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E49-2 - E28-68 (PRG) Always Below 1 Ω
E49-2 or E28-68 (PRG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - NO. 1 INTEGRATION RELAY)
a.

Disconnect the purge VSV connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E49-1 - 1A-8 Always Below 1 Ω
E49-1 or 1A-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR