Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM J

2AR-FXE ENGINE CONTROL  SFI SYSTEM  Fuel Injector Circuit  


DESCRIPTION

The fuel injectors are located on the intake port. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

A268323
1.188,1.667 1.438,1.823 0.25,0.156 10 false IG2 0.635,2.698 2.083,2.979 1.448,0.281 10 false No. 1 Integration Relay 0.5,6.188 1.104,6.656 0.604,0.469 10 false Auxiliary Battery 5.208,4.552 5.385,4.708 0.177,0.156 10 false 19 5.208,2.052 5.385,2.208 0.177,0.156 10 false 17 5.208,0.813 5.385,0.969 0.177,0.156 10 false 20 5.208,3.302 5.385,3.458 0.177,0.156 10 false 18 5.188,5.615 5.365,5.771 0.177,0.156 10 false 50 5.188,6.198 5.365,6.354 0.177,0.156 10 false 49 6.219,7.177 6.552,7.333 0.333,0.156 10 false ECM 4.51,0.792 4.615,0.948 0.104,0.156 10 false 2 3.854,0.792 3.958,0.948 0.104,0.156 10 false 1 3.417,1.094 3.688,1.25 0.271,0.156 10 false E29 3.417,1.229 5.292,1.479 1.875,0.25 10 false No. 1 Fuel Injector Assembly 5.469,0.813 5.719,0.969 0.25,0.156 10 false #10 5.469,2.052 5.719,2.208 0.25,0.156 10 false #20 5.469,3.302 5.719,3.458 0.25,0.156 10 false #30 5.469,4.552 5.719,4.708 0.25,0.156 10 false #40 5.448,5.615 5.719,5.771 0.271,0.156 10 false E01 5.448,6.198 5.719,6.354 0.271,0.156 10 false E02 5.906,7.177 6.188,7.333 0.281,0.156 10 false E28 2.177,2.49 2.375,2.646 0.198,0.156 10 false 1C 2.167,2.323 2.271,2.479 0.104,0.156 10 false 8 2.49,0.885 2.688,1.042 0.198,0.156 10 false 1A 2.542,0.719 2.646,0.875 0.104,0.156 10 false 3 2.49,1.354 2.688,1.51 0.198,0.156 10 false 1E 2.552,1.177 2.656,1.333 0.104,0.156 10 false 2 0.417,3.802 1.063,3.958 0.646,0.156 10 false IG2-MAIN 1.938,1.042 2.198,1.198 0.26,0.156 10 false INJ 0.219,2.5 0.417,2.656 0.198,0.156 10 false 1D 0.333,2.323 0.438,2.479 0.104,0.156 10 false 3 2.094,3.969 2.198,4.125 0.104,0.156 10 false 2 1.698,4.063 2.052,4.219 0.354,0.156 10 false IG2D 1.104,4.542 1.406,4.698 0.302,0.156 10 false A39 1.104,4.688 2.417,5.083 1.313,0.396 10 false Power Management Control ECU 0.406,5.104 0.792,5.26 0.385,0.156 10 false MAIN 4.521,2.031 4.625,2.188 0.104,0.156 10 false 2 3.854,2.031 3.958,2.188 0.104,0.156 10 false 1 3.417,2.333 3.688,2.49 0.271,0.156 10 false E34 3.417,2.469 5.271,2.76 1.854,0.292 10 false No. 2 Fuel Injector Assembly 4.51,3.292 4.615,3.448 0.104,0.156 10 false 2 3.844,3.292 3.948,3.448 0.104,0.156 10 false 1 3.417,3.594 3.688,3.75 0.271,0.156 10 false H1 3.417,3.729 5.229,4.021 1.813,0.292 10 false No. 3 Fuel Injector Assembly 4.51,4.552 4.615,4.708 0.104,0.156 10 false 2 3.844,4.552 3.948,4.708 0.104,0.156 10 false 1 3.417,4.833 3.688,4.99 0.271,0.156 10 false H2 3.417,4.99 5.281,5.333 1.865,0.344 10 false No. 4 Fuel Injector Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
a.
A281034
0.229,0.979 0.583,1.25 0.354,0.271 0.667,0.979 1.021,1.25 0.354,0.271 0.667,1.313 1.021,1.583 0.354,0.271 0.229,1.313 0.583,1.583 0.354,0.271 0.135,0.135 0.448,0.333 0.313,0.198 10 false *a 0.292,1.031 0.604,1.229 0.313,0.198 10 false E29 0.74,1.042 1.052,1.24 0.313,0.198 10 false E34 0.323,1.375 0.635,1.573 0.313,0.198 10 false H1 0.76,1.375 1.073,1.573 0.313,0.198 10 false H2
*a Front view of wire harness connector
(to Fuel Injector Assembly)


Disconnect the fuel injector assembly connectors.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E29-1 - Body ground Power switch on (IG) 11 to 14 V
E34-1 - Body ground Power switch on (IG) 11 to 14 V
H1-1 - Body ground Power switch on (IG) 11 to 14 V
H2-1 - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT FUEL INJECTOR ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - NO. 1 INTEGRATION RELAY)
2.INSPECT FUEL INJECTOR ASSEMBLY
a.

Check the fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FXE FUEL>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the fuel injector assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E29-2 - E28-20 (#10) Always Below 1 Ω
E34-2 - E28-17 (#20) Always Below 1 Ω
H1-2 - E28-18 (#30) Always Below 1 Ω
H2-2 - E28-19 (#40) Always Below 1 Ω
E29-2 or E28-20 (#10) - Body ground Always 10 kΩ or higher
E34-2 or E28-17 (#20) - Body ground Always 10 kΩ or higher
H1-2 or E28-18 (#30) - Body ground Always 10 kΩ or higher
H2-2 or E28-19 (#40) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the fuel injector assembly connectors.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
E29-1 - 1A-3 Always Below 1 Ω
E34-1 - 1A-3 Always Below 1 Ω
H1-1 - 1A-3 Always Below 1 Ω
H2-1 - 1A-3 Always Below 1 Ω
E29-1 or 1A-3 - Body ground Always 10 kΩ or higher
E34-1 or 1A-3 - Body ground Always 10 kΩ or higher
H1-1 or 1A-3 - Body ground Always 10 kΩ or higher
H2-1 or 1A-3 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR