Home › Engine / Hybrid System › 2AR-FXE FUEL › FUEL INJECTOR
RM2040EQ _51 Engine / Hybrid System _014694 2AR-FXE FUEL _0074910 FUEL INJECTOR A

2AR-FXE FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCHARGE FUEL SYSTEM PRESSURE

Hide 64718C 3.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 4.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 23901 6.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A259299

Remove the No. 1 fuel pipe clamp.


b.
A284010C02
2.167,3.469 2.573,2.969 2.573,2.969 2.802,2.969 false 1.896,3.271 1.729,2.958 1.729,2.958 1.542,2.958 false 0.844,3.417 0.677,3.104 0.677,3.104 0.49,3.104 false 1.146,4.115 1.563,4.115 1.563,4.115 1.563,3.823 false 1.396,4.115 1.396,3.802 false 2.396,4.083 3.229,4.083 3.229,4.083 3.229,3.792 false 2.5,4.083 2.5,3.792 false 2.885,2.896 3.198,3.052 0.313,0.156 10 *1 1.365,2.885 1.677,3.042 0.313,0.156 10 *2 0.302,3.042 0.615,3.198 0.313,0.156 10 *3 0.958,4.052 1.271,4.208 0.313,0.156 10 *4 2.198,4.021 2.51,4.177 0.313,0.156 10 *5
*1 Fuel Pipe
*2 Fuel Tube Connector
*3 Nylon Tube
*4 O-ring
*5 Retainer
V100135

Pinch
V100136

Pull


Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:
·

Check for foreign matter on the fuel tube around the fuel tube connector. Clean it if necessary. Foreign matter can affect the ability of the O-ring to seal the fuel tube connector and fuel pipe.

·

Do not use any tools to separate the fuel tube connector and fuel pipe.

·

Do not forcefully bend, kink or twist the nylon tube.

·

Keep the fuel tube connector and fuel pipe free from foreign matter.

·

If the fuel tube connector and fuel pipe are stuck, push and pull to release them.

·

Put the fuel tube connector and fuel pipe in plastic bags to prevent damage and contamination.




c.

Remove the fuel tube sub-assembly from the fuel hose clamp.


Hide 23814B 7.REMOVE FUEL DELIVERY PIPE

a.
A259301

Disconnect the 4 fuel injector connectors.


b.

Remove the 2 bolts, and then remove the fuel delivery pipe together with the 4 fuel injectors.

NOTICE:

Be careful not to drop the fuel injectors when removing the fuel delivery pipe.



c.
A259322

Remove the 2 fuel delivery spacers from the cylinder head.


d.

Remove the 4 injector vibration insulators from the cylinder head.


Hide 23250 8.REMOVE FUEL INJECTOR ASSEMBLY

a.
A284011

Pull the 4 fuel injectors out of the fuel delivery pipe.


b.

Remove the O-ring from each fuel injector.


c.

For reinstallation, attach a tag or label to each injector shaft.

NOTICE:

Prevent entry of foreign matter by covering the fuel injectors with plastic bags.