Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2015.04
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3004-800  High Voltage Power Resource  P3004-801  High Voltage Power Resource  


DESCRIPTION

Refer to the description for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3004-800 High Voltage Power Resource Excessive overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on).
·

Wire harness or connector

·

No. 4 engine wire

·

Compressor with motor assembly

·

Inverter with converter assembly

·

Hybrid battery junction block assembly

·

No. 4 floor wire

·

Power management control ECU


Does not come on Master Warning Light:
Comes on
P3004-801 High Voltage Power Resource Minimal overcurrent occurs during precharge (time from when SMRP turns on until when SMRG turns on).
·

Wire harness or connector

·

No. 4 engine wire

·

Compressor with motor assembly

·

Inverter with converter assembly

·

Hybrid battery junction block assembly

·

No. 4 floor wire

·

Power management control ECU


Does not come on Master Warning Light:
Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A08-264 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A08-264).

Refer to the wiring diagram for DTC P0AA6-526 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AA6-526).

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).


CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.


d.

Check for DTCs.

Powertrain > Hybrid Control > Trouble Codes
50001 236
Result:
Result Proceed to
P3004-800 or P3004-801 only is output. A
DTCs shown in Table 1 are output simultaneously. B
DTCs shown in Table 2 are output simultaneously. C


Table 1
DTC No. Relevant Diagnosis
P0A09-265 DC/DC Converter Status Circuit Low Input
P0A10-263 DC/DC Converter Status Circuit High Input

Table 2
DTC No. Relevant Diagnosis
P0ABF-123 Hybrid Battery Pack Current Sensor Circuit
P0AC0-123 Hybrid Battery Pack Current Sensor Circuit Range / Performance
P0AC1-123 Hybrid Battery Pack Current Sensor Circuit Low
P0AC2-123 Hybrid Battery Pack Current Sensor Circuit High
P0AFC-123 Hybrid Battery Pack Sensor Module
P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low
P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low
P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low
P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low
P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low
P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low
P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low
P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low
P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low
P0B6A-123 Hybrid Battery Voltage Sensor "J" Circuit Low
P0B6F-123 Hybrid Battery Voltage Sensor "K" Circuit Low
P0B74-123 Hybrid Battery Voltage Sensor "L" Circuit Low
P0B79-123 Hybrid Battery Voltage Sensor "M" Circuit Low
P0B7E-123 Hybrid Battery Voltage Sensor "N" Circuit Low
P0B83-123 Hybrid Battery Voltage Sensor "O" Circuit Low
P0B88-123 Hybrid Battery Voltage Sensor "P" Circuit Low
P0B8D-123 Hybrid Battery Voltage Sensor "Q" Circuit Low
P0B92-123 Hybrid Battery Voltage Sensor "R" Circuit Low
P308A-123 Hybrid Battery Voltage Sensor All Circuits Low
U029A-123 Lost Communication with Hybrid Battery Pack Sensor Module

HINT:

P3004-800 or P3004-801 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.



e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

B

C

2.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

3.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

NG

CONNECT SECURELY

3.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259713E02
1.573,1.385 1.948,1.656 0.375,0.271 1.604,1.417 1.917,1.615 0.313,0.198 10 true G2

Disconnect connector G2 of the No. 4 engine wire (air conditioning harness) from the inverter with converter assembly.


c.
A260188C17
0.698,1.302 1.042,1.552 0.344,0.25 1.135,1.917 1.583,1.51 false 2.271,1.906 1.885,1.51 false 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.781,1.354 1.021,1.531 0.24,0.177 10 false G2 0.771,1.844 1.167,2.01 0.396,0.167 10 false ACPE 2.344,1.844 2.74,2.01 0.396,0.167 10 false ACPB
*a No. 4 engine wire (Air Conditioning Harness)
(Inverter with Converter Assembly Side)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
(Tester Probe Polarity)
Switch Condition Specified Condition
G2-1 (ACPE) (Negative probe) - G2-2 (ACPB) (Positive probe) Power switch off 100 kΩ or higher


NOTICE:
·

Do not use a megohmmeter.

·

Read the resistance after the value has stabilized.



HINT:

The polarities of the tester probes may differ depending on the tester. Use the current output probe of the tester as the positive probe for this measurement. To determine the polarity, use another voltmeter to confirm the current output probe of the tester. When measuring the output of the tester, the voltmeter positive probe indicates the tester current output probe.



d.

Connect the No. 4 engine wire (air conditioning harness) to the inverter with converter assembly.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)

NG

7.CHECK NO. 4 ENGINE WIRE
4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect connector A13 from the inverter with converter assembly.


c.

Disconnect connector A38 from power management control ECU.


d.
A259909C15
1.542,0.313 1.958,0.552 0.417,0.24 1.302,3.813 1.719,4.052 0.417,0.24 1.49,1.333 0.948,1.583 true 0.99,3.969 1.302,4.333 true 0.177,0.156 0.51,0.406 0.333,0.25 10 false *a 0.49,1.521 0.979,1.75 0.49,0.229 10 false NODD 0.177,2.219 0.448,2.417 0.271,0.198 10 false *b 1.375,4.302 1.813,4.5 0.438,0.198 10 false NODD 1.615,0.354 1.99,0.625 0.375,0.271 10 false A13 1.385,3.844 1.813,4.135 0.427,0.292 10 false A38
*a Front view of wire harness connector
(to Inverter with Converter Assembly)
*b Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
A13-5 (NODD) - A38-21 (NODD) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
A13-5 (NODD) or A38-21 (NODD) - Body ground and other terminals Power switch off 10 kΩ or higher



e.

Connect the power management control ECU connector.


f.

Connect the inverter with converter assembly connector.

Result:
Proceed to
OK
NG




OK

5.CHECK POWER MANAGEMENT CONTROL ECU (NODD)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POWER MANAGEMENT CONTROL ECU (NODD)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Connect the cable to the negative (-) auxiliary battery terminal.


c.

Turn the power switch on (IG).


d.
A204442C27
0.615,1.073 1.031,1.313 0.417,0.24 1.844,1.073 2.26,1.313 0.417,0.24 0.865,1.969 1.094,2.406 false 1.823,1.833 2.063,2.396 false 0.698,1.115 0.969,1.281 0.271,0.167 10 false A38 2.01,1.115 2.281,1.281 0.271,0.167 10 false I3 0.177,0.229 0.365,0.417 0.188,0.188 10 false *a 0.948,2.438 1.385,2.625 0.438,0.188 10 false NODD 2.021,2.417 2.208,2.604 0.188,0.188 10 false E1
*a Component with harness connected
(Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-21 (NODD) - I3-6 (E1) Power switch on (IG) Less than 1.5 V



e.

Turn the power switch off.


f.

Disconnect the cable from the negative (-) auxiliary battery terminal.


Result:
Proceed to
OK
NG



OK

6.CHECK NO. 4 FLOOR WIRE

NG

6.CHECK NO. 4 FLOOR WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259710

Remove the connector cover assembly from the inverter with converter assembly.


c.
A259712E07
1.583,0.979 1.865,1.177 0.281,0.198 1.656,1 1.854,1.156 0.198,0.156 8 false Q1

Disconnect connector Q1 of the No. 4 floor wire from the inverter with converter assembly.


d.

Remove the No. 4 hybrid battery shield panel

(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


e.
A259724E02
1.49,0.323 1.979,0.615 0.49,0.292 0.521,1.01 1.01,1.302 0.49,0.292 1.542,0.375 1.885,0.583 0.344,0.208 10 true Q2 0.646,1.063 0.969,1.26 0.323,0.198 10 true Q3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q2-1 (CBI) - Q3-1 (CEI) Power switch off 10 kΩ or higher



f.

Install the No. 4 hybrid battery shield panel.


g.

Connect the No. 4 floor wire.


h.

Install the connector cover assembly.

Result:
Proceed to
OK
NG




OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

8.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY
7.CHECK NO. 4 ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259713E02
1.573,1.385 1.948,1.656 0.375,0.271 1.604,1.417 1.917,1.615 0.313,0.198 10 true G2

Disconnect connector G2 of the No. 4 engine wire (air conditioning harness) from the inverter with converter assembly.


c.
A259733C02
1.49,1.438 1.979,1.729 0.49,0.292 0.938,0.25 1.469,0.198 false 1.531,1.479 1.906,1.698 0.375,0.219 10 true G1 1.531,0.115 1.802,0.333 0.271,0.219 10 false *1
*1 Green Lock


Disconnect connector G1 of the No. 4 engine wire (air conditioning harness) from the compressor with motor assembly.


d.
A260188C17
0.698,1.302 1.042,1.552 0.344,0.25 1.135,1.917 1.583,1.51 false 2.271,1.906 1.885,1.51 false 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.781,1.354 1.021,1.531 0.24,0.177 10 false G2 0.771,1.844 1.167,2.01 0.396,0.167 10 false ACPE 2.344,1.844 2.74,2.01 0.396,0.167 10 false ACPB
*a No. 4 engine wire (Air Conditioning Harness)
(Inverter with Converter Assembly Side)


Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
G2-1 (ACPE) - G2-2 (ACPB) Power switch off 10 kΩ or higher


e.

Connect the No. 4 engine wire (air conditioning harness) to the compressor with motor assembly.


f.

Connect the No. 4 engine wire (air conditioning harness) to the inverter with converter assembly.

Result:
Proceed to
OK
NG




OK

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPLACE NO. 4 ENGINE WIRE

8.CHECK HV BATTERY JUNCTION BLOCK ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 4 hybrid battery shield panel

(Click here Engine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL).


c.
A259723N07
0.427,0.563 0.917,0.854 0.49,0.292 1.615,0.125 2.104,0.417 0.49,0.292 0.573,0.625 0.823,0.813 0.25,0.188 10 true Q3 1.677,0.198 1.979,0.375 0.302,0.177 10 true Q2

Disconnect connector Q2 and connector Q3 of the No. 4 floor wire from the hybrid battery junction block assembly.


d.
A260252N02
0.448,0.896 0.938,1.188 0.49,0.292 1.281,0.208 1.771,0.5 0.49,0.292 0.552,0.948 0.844,1.156 0.292,0.208 10 true Q3 1.323,0.26 1.656,0.448 0.333,0.188 10 true Q2

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q3-1 (CEI) - Q2-1 (CBI) Power switch off 10 kΩ or higher


e.

Connect the No. 4 floor wire.


f.

Install the No. 4 hybrid battery shield panel.

Result:
Proceed to
OK
NG




OK

NG

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY