Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.02–2016.05
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074885 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AA6-526  Hybrid Battery Voltage System Isolation Fault  P0AA6-611  Hybrid Battery Voltage System Isolation Fault  P0AA6-612  Hybrid Battery Voltage System Isolation Fault  P0AA6-613  Hybrid Battery Voltage System Isolation Fault  P0AA6-614  Hybrid Battery Voltage System Isolation Fault  


DESCRIPTION

The power management control ECU monitors the battery smart unit and detects insulation malfunctions in the high-voltage system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AA6-526 Hybrid Battery Voltage System Isolation Fault Insulation resistance between the high-voltage circuit and the body has decreased.*1*2
·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly

·

No. 4 floor wire

·

No. 4 engine wire

·

Hybrid battery junction block assembly

·

Air conditioning system

·

HV battery

·

Battery smart unit


Does not come on Master Warning Light:
Comes on
P0AA6-611 Hybrid Battery Voltage System Isolation Fault Insulation resistance of the high voltage circuit in the air conditioning system has decreased.*3 Air conditioning system Does not come on Master Warning Light:
Comes on
P0AA6-612 Hybrid Battery Voltage System Isolation Fault Insulation resistance of the HV battery area has decreased.*3
·

Hybrid battery junction block assembly

·

Battery smart unit

·

HV battery


Does not come on Master Warning Light:
Comes on
P0AA6-613 Hybrid Battery Voltage System Isolation Fault Insulation resistance of the transaxle area has decreased.*3
·

Hybrid vehicle transaxle assembly

·

Inverter with converter assembly


Does not come on Master Warning Light:
Comes on
P0AA6-614 Hybrid Battery Voltage System Isolation Fault Insulation resistance of the high-voltage DC area has decreased.*3
·

Inverter with converter assembly

·

No. 4 floor wire

·

Air conditioning system

·

No. 4 engine wire

·

Hybrid battery junction block assembly


Does not come on Master Warning Light:
Comes on

HINT:
·

*1: INF code 526 is stored together with P0AA6.

·

*2: The insulation malfunction detection circuit in the battery smart unit monitors the insulation resistance between the high voltage circuits and body. If the insulation resistance decreases, the power management control ECU stores DTC P0AA6-526 and illuminates the MIL first.

·

*3: If the following operations are performed within the same trip after DTC P0AA6-526 is stored, just one of the related DTCs (P0AA6-611, 612, 613 or 614) will be stored.

1.

Apply the parking brake firmly.

2.

Wait for 1 minute or more with the vehicle stopped, the brake pedal firmly depressed, the power switch on (READY), the shift lever in D and the air conditioning system on (Lo/COOL MAX, blower speed HI), then turn the power switch off and wait for 1 minute or more.


·

If DTC P0AA6 is stored, the vehicle cannot start.

·

When measuring insulation resistance using a megohmmeter, measure the resistance while jiggling the high voltage wire harness.



WIRING DIAGRAM

A260182E01
0.082,0.042 0.298,0.225 0.216,0.183 10 *a 3.41,7.48 3.626,7.664 0.216,0.183 10 *b 5.664,7.137 5.88,7.321 0.216,0.183 10 *c 1.442,6.399 1.659,6.582 0.216,0.183 10 *d 6.148,4.578 6.365,4.761 0.216,0.183 10 *e 3.74,7.137 3.957,7.321 0.216,0.183 10 *f 1.489,1.063 1.706,1.247 0.216,0.183 10 *1 1.786,3.133 2.003,3.316 0.216,0.183 10 *2 3.037,1.815 3.254,1.999 0.216,0.183 10 *3 3.037,3.898 3.254,4.082 0.216,0.183 10 *4 3.037,4.526 3.254,4.709 0.216,0.183 10 *5 2.259,4.651 2.475,4.835 0.216,0.183 10 *6 0.425,2.999 0.641,3.182 0.216,0.183 10 *7 4.049,1.078 4.266,1.261 0.216,0.183 10 *8 4.404,2.103 4.62,2.286 0.216,0.183 10 *9 5.241,3.126 5.548,3.309 0.308,0.183 10 *10 6.214,2.742 6.522,2.925 0.308,0.183 10 *11 6.214,3.585 6.522,3.769 0.308,0.183 10 *12 4.094,5.332 4.402,5.515 0.308,0.183 10 *13 4.373,6.121 4.681,6.304 0.308,0.183 10 *14 5.679,6.136 5.987,6.32 0.308,0.183 10 *15

Text in Illustration
*1 HV Battery *2 Battery Smart Unit
*3 SMRB *4 SMRG
*5 SMRP *6 System Main Resistor
*7 Service Plug Grip *8 Inverter with Converter Assembly
*9 Boost Converter *10 Inverter
*11 MG1 *12 MG2
*13 Compressor with Motor Assembly *14 A/C Inverter
*15 A/C Motor - -
*a High-voltage Areas *b INF Code 526 Vehicle Insulation Resistance Reduction Area
*c INF Code 611 Air Conditioning System Area *d INF Code 612 HV Battery Area
*e INF Code 613 Transaxle Area *f INF Code 614 High Voltage Direct Current Area

A260420E01
0.484,1.235 1.221,1.424 0.737,0.189 10 HV Battery 0.484,2.805 1.221,2.994 0.737,0.189 10 HV Battery 0.056,2.071 1.187,2.268 1.131,0.197 10 Service Plug Grip 2.646,3.973 5.153,4.135 2.508,0.161 10 Hybrid Battery Junction Block Assembly 0.7,5.523 2.315,5.883 1.615,0.36 10 Hybrid Vehicle Transaxle Assembly (Motor) 0.7,7.219 2.293,7.577 1.592,0.358 10 Hybrid Vehicle Transaxle Assembly (Generator) 3.388,7.135 5.591,7.336 2.203,0.2 10 Inverter with Converter Assembly 3.383,8.445 5.533,8.621 2.15,0.177 10 Compressor with Motor Assembly 0.942,3.908 2.387,4.07 1.445,0.163 10 System Main Resistor 3.279,3.553 2.354,3.982 false 3.632,1.003 4.072,1.182 0.44,0.179 10 SMRB 3.632,2.36 4.072,2.538 0.44,0.179 10 SMRG 3.645,3.689 4.085,3.867 0.44,0.179 10 SMRP 2.399,0.669 2.545,0.831 0.146,0.163 10 A 2.368,2.012 2.584,2.191 0.216,0.179 10 q1 2.405,0.505 2.551,0.668 0.146,0.163 10 1 2.405,1.854 2.551,2.017 0.146,0.163 10 1 2.655,0.565 2.806,0.714 0.152,0.149 10 + 2.673,1.896 2.825,2.045 0.152,0.149 10 - 5.229,0.673 5.462,0.836 0.234,0.163 10 Q2 5.242,2.017 5.475,2.18 0.234,0.163 10 Q3 5.287,0.497 5.433,0.659 0.146,0.163 10 1 5.287,1.845 5.433,2.007 0.146,0.163 10 1 4.876,0.541 5.171,0.7 0.295,0.158 10 CBI 4.876,1.84 5.171,1.998 0.295,0.158 10 CEI 2.004,4.498 2.181,4.659 0.178,0.161 10 W 2.032,4.846 2.209,5.007 0.178,0.161 10 V 2.032,5.197 2.209,5.358 0.178,0.161 10 U 3.753,4.514 3.93,4.676 0.178,0.161 10 W 3.767,4.862 3.944,5.023 0.178,0.161 10 V 3.767,5.213 3.944,5.375 0.178,0.161 10 U 2.206,4.387 2.336,4.549 0.13,0.162 10 3 2.206,4.737 2.336,4.898 0.13,0.162 10 2 2.206,5.092 2.336,5.253 0.13,0.162 10 1 3.507,5.046 3.637,5.208 0.13,0.162 10 3 3.507,4.682 3.637,4.843 0.13,0.162 10 2 3.507,4.314 3.637,4.476 0.13,0.162 10 1 3.468,4.489 3.661,4.637 0.193,0.148 10 n1 3.468,4.844 3.661,4.993 0.193,0.148 10 n1 3.468,5.208 3.661,5.357 0.193,0.148 10 n1 2.003,6.175 2.181,6.337 0.178,0.161 10 W 2.031,6.523 2.209,6.684 0.178,0.161 10 V 2.031,6.874 2.209,7.036 0.178,0.161 10 U 3.752,6.178 3.93,6.339 0.178,0.161 10 W 3.766,6.525 3.944,6.686 0.178,0.161 10 V 3.766,6.877 3.944,7.038 0.178,0.161 10 U 2.206,6.759 2.336,6.921 0.13,0.162 10 3 2.206,6.414 2.336,6.576 0.13,0.162 10 2 2.206,6.049 2.336,6.211 0.13,0.162 10 1 3.507,6.709 3.637,6.871 0.13,0.162 10 3 3.507,6.345 3.637,6.507 0.13,0.162 10 2 3.507,5.978 3.637,6.139 0.13,0.162 10 1 3.468,6.167 3.661,6.315 0.193,0.148 10 o1 3.468,6.522 3.661,6.67 0.193,0.148 10 o1 3.468,6.886 3.661,7.034 0.193,0.148 10 o1 5.236,4.577 5.453,4.731 0.217,0.154 10 Q1 5.244,5.118 5.461,5.272 0.217,0.154 10 Q1 5.288,4.951 5.413,5.105 0.125,0.154 10 1 5.298,4.406 5.424,4.56 0.125,0.154 10 2 4.879,4.568 5.173,4.723 0.293,0.154 10 CEI 4.882,5.124 5.176,5.278 0.293,0.154 10 CBI 5.235,6.339 5.472,6.48 0.237,0.141 10 G2 5.236,6.881 5.473,7.022 0.237,0.141 10 G2 5.308,6.714 5.431,6.854 0.123,0.141 10 2 5.3,6.164 5.423,6.304 0.123,0.141 10 1 4.75,6.334 5.157,6.474 0.407,0.141 10 ACPE 4.75,6.875 5.157,7.015 0.407,0.141 10 ACPB 4.927,7.658 5.159,7.807 0.232,0.149 10 PB 4.927,7.991 5.159,8.14 0.232,0.149 10 PE 5.203,7.541 5.326,7.682 0.123,0.141 10 2 5.203,7.885 5.326,8.026 0.123,0.141 10 1 3.384,8.287 3.617,8.436 0.232,0.149 10 G1 0.704,5.374 0.936,5.523 0.232,0.149 10 n2 0.692,7.076 0.924,7.225 0.232,0.149 10 o2 1.289,8.409 2.511,8.558 1.222,0.15 10 : High Voltage Line

SYSTEM DESCRIPTION

HINT:

If a decrease in insulation resistance cannot be confirmed using a megohmmeter, check the Short Wave Highest Val in the Data List.


Characteristics of Short Wave Highest Value


a.

The Data List item Short Wave Highest Val and insulation resistance have the relationship shown in the table below. Short Wave Highest Val decreases with a decrease in insulation resistance. However, in some cases, even though the insulation resistance of the vehicle is normal, Short Wave Highest Val may decrease. Therefore, check Short Wave Highest Val while considering the following.

·

Do not check until approximately 1 minute has passed after the power switch is turned on (IG) (*1).

·

Do not check when there is a difference between the system voltages (Power Resource VB, VL-Voltage before Boosting, and VH-Voltage after Boosting) (*2).

Short Wave Highest Value Trouble Area
Neither condition (*1) nor (*2) is met and Short Wave Highest Val is approximately 0 V Since the insulation resistance is close to 0 Ω, there is a strong possibility of interference with a metal object.
Neither condition (*1) nor (*2) is met and Short Wave Highest Val is between 0 and 5 V Since the insulation resistance is several hundred kilo ohms, there is a strong possibility of the presence of fluid such as coolant.




How to Determine Part with Insulation Malfunction


a.

Jiggle the high-voltage wire harness to check if the resistance to body ground changes with the position of the wire harness or force applied.


b.

Repeat rotating and stopping of the MG1, MG2 and compressor with motor assembly. Check that the Short Wave Highest Val does not decrease (for example if the motor stops with foreign matter forming a leak path) when the motor stops, or that the Short Wave Highest Val does not return to normal (for example if foreign matter moves away from the leak path) when the motor rotates.


c.

Increase the temperature of MG1and MG2. Check if the Short Wave Highest Val decreases with the temperature increase.


d.

Check that the transaxle fluid is not cloudy and the coolant level in the reserve tank has not dropped as the transaxle fluid will become cloudy when mixed with coolant, resulting in low insulation resistance.



CAUTION / NOTICE / HINT

CAUTION:
·

When performing P0AA6 troubleshooting, use either a tool wrapped with vinyl insulation tape or a insulated tool. (It is extremely dangerous when a high-voltage charge passes through a non-insulated tool causing a short.)

·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.


·

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.



NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

When measuring insulation resistance using a megohmmeter, set the megohmmeter to 500 V.


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Check if DTCs are output.

Result:
Result Proceed to
P0AA6 only is output. A
P0AA6 and P0A1D (power management control ECU malfunction) are output. B
P0AA6 and P0AA7 (malfunction in the battery smart unit) are output. C
P0AA6 and P0AFC (Hybrid Battery Pack Sensor Module) are output. D



e.

Turn the power switch off.



A

2.CHECK INFORMATION CODE

B

C

D

2.CHECK INFORMATION CODE
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / DTC.

Powertrain > Hybrid Control > Trouble Codes
50001 236

d.

Access the freeze frame data of DTC P0AA6 and read the INF code.

NOTICE:
·

Information codes 611, 612, 613 and 614 are not stored with 526 simultaneously. If a drop in insulation resistance is detected and DTC P0AA6-526 is output, turn the power switch on (READY) and wait for 1 minute with the shift lever in D and the air conditioning system on, then turn the power switch off and wait for 1 minute to determine on of the information code (611, 612, 613 or 614).

·

If only DTC P0AA6-526 is output, perform the diagnosis procedure for INF code 526 to inspect all the high voltage circuits.



Result:
Result Proceed to
526 (decrease in the insulation resistance of the high-voltage circuit) only is output. A
526 and 611 (decrease in the insulation resistance of the air conditioning system area) are output. Refer to the troubleshooting procedures for P0AA6-611 (Air conditioning system)
(Click here (Click here))
526 and 612 (decrease in the insulation resistance of the battery area) are output. B
526 and 613 (decrease in the insulation resistance of the transaxle area) are output. C
526 and 614 (decrease in the insulation resistance of the high-voltage DC area) are output. D



e.

Turn the power switch off.



A

3.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR)

B

8.CHECK HV BATTERY AREA

C

11.CHECK INVERTER WITH CONVERTER ASSEMBLY

D

13.CHECK HIGH VOLTAGE DIRECT CURRENT AREA
3.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258636

Remove the upper inverter cover (generator cable side) and upper inverter cover (motor cable side) from the inverter with converter assembly.

HINT:

Make sure that no foreign objects have entered or contaminated the inverter with converter assembly.



c.
A258637C06
2.021,0.531 2.333,0.375 false 1.042,0.417 0.76,0.5 false 2.365,0.271 2.604,0.458 0.24,0.188 10 true *1 0.563,0.438 0.75,0.635 0.188,0.198 10 true *2
*1 Generator Cable
*2 Motor Cable


Disconnect the motor cable and generator cable from the inverter with converter assembly.


d.
A258955C13
2.708,1 3.073,1.24 0.365,0.24 1.469,1.146 1.323,1.542 false 1.771,1.156 1.75,1.604 false 2.208,1.146 2.302,1.573 false 0.667,0.99 1.177,0.854 false 0.083,0.042 0.313,0.24 0.229,0.198 10 false *a 0.458,0.927 0.688,1.125 0.229,0.198 10 false *1 1.219,1.563 1.438,1.729 0.219,0.167 10 false W 1.688,1.615 1.906,1.813 0.219,0.198 10 false V 2.25,1.594 2.448,1.792 0.198,0.198 10 false U 2.792,1.031 3,1.198 0.208,0.167 10 false n1
*1 Shield Ground
*a Motor Cable
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
n1-3 (U) - Body ground and shield ground Power switch off 100 MΩ or higher
n1-2 (V) - Body ground and shield ground Power switch off 100 MΩ or higher
n1-1 (W) - Body ground and shield ground Power switch off 100 MΩ or higher


Result:
Proceed to
OK
NG




OK

4.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR)

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

4.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258955C14
0.088,0.041 0.319,0.243 0.231,0.201 10 *a 0.46,0.929 0.691,1.123 0.23,0.193 10 *1 1.217,1.565 1.433,1.731 0.216,0.166 10 W 1.692,1.617 1.916,1.817 0.223,0.2 10 V 2.248,1.594 2.446,1.792 0.198,0.198 10 U 1.472,1.147 1.32,1.54 false 1.774,1.153 1.755,1.603 false 2.213,1.144 2.299,1.577 false 0.669,0.99 1.181,0.856 false 2.71,1.003 3.075,1.246 0.365,0.244 2.792,1.034 3.004,1.197 0.212,0.163 10 o1
*1 Shield Ground
*a Generator Cable
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
o1-3 (U) - Body ground and shield ground Power switch off 100 MΩ or higher
o1-2 (V) - Body ground and shield ground Power switch off 100 MΩ or higher
o1-1 (W) - Body ground and shield ground Power switch off 100 MΩ or higher


Result:
Proceed to
OK
NG




OK

5.CHECK NO. 4 ENGINE WIRE

NG

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

5.CHECK NO. 4 ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259710

Remove the connector cover assembly from the inverter with converter assembly.

HINT:

Make sure that no foreign objects have entered or contaminated the inverter with converter assembly.



c.
A259717N02
0.698,1.49 1.188,1.781 0.49,0.292 0.854,1.531 1.083,1.74 0.229,0.208 10 true G2

Disconnect connector G2 of the No. 4 engine wire (air conditioning harness) from the inverter with converter assembly.

HINT:

Make sure that no foreign objects have entered or contaminated connector G2 of the No. 4 engine wire (air conditioning harness).



d.
A260188C48
0.698,1.302 1.042,1.552 0.344,0.25 1.135,1.917 1.583,1.51 false 2.271,1.906 1.885,1.51 false 2.073,0.938 2.427,0.76 false 2.479,0.698 2.792,0.854 0.313,0.156 10 false *1 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.781,1.354 1.021,1.531 0.24,0.177 10 false G2 0.708,1.875 1.104,2.042 0.396,0.167 10 false ACPE 2.354,1.865 2.75,2.031 0.396,0.167 10 false ACPB
*1 Shield Ground
*a No. 4 Engine Wire (Air Conditioning Harness)
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
G2-1 (ACPE) - Body ground and shield ground Power switch off 3 MΩ or higher
G2-2 (ACPB) - Body ground and shield ground Power switch off 3 MΩ or higher


Result:
Proceed to
OK
NG




OK

6.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

12.CHECK NO. 4 ENGINE WIRE
6.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259716E02
1.198,0.719 1.688,1.01 0.49,0.292 1.323,0.771 1.594,0.958 0.271,0.188 10 true Q1

Disconnect connector Q1 of the No. 4 floor wire from the inverter with converter assembly.

HINT:

Make sure that no foreign objects have entered or contaminated connector Q1 of the No. 4 floor wire.



c.
A259718C03
2.84,0.485 3.029,0.67 0.189,0.185 10 *1 1.865,0.57 2.811,0.57 false
*1 High Voltage Fuse


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
High voltage fuse terminal - Body ground Power switch off 1 MΩ or higher


HINT:

Perform this inspection with the motor cable, generator cable and No. 4 engine wire (air conditioning harness) disconnected from the inverter with converter assembly.


Result:
Proceed to
OK
NG




OK

7.CHECK NO. 4 FLOOR WIRE

NG

REPLACE INVERTER WITH CONVERTER ASSEMBLY

7.CHECK NO. 4 FLOOR WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259783C03
0.083,0.025 0.355,0.224 0.272,0.199 10 *a 0.503,1.077 0.99,1.369 0.487,0.292 0.628,1.134 0.831,1.315 0.203,0.182 10 Q1 0.643,1.713 0.951,1.894 0.308,0.181 10 CBI 2.272,1.713 2.58,1.894 0.308,0.181 10 CEI 2.519,0.869 2.753,1.048 0.233,0.179 10 *1 1.342,1.423 0.976,1.788 false 1.853,1.423 2.218,1.788 false 2.144,1.07 2.497,0.966 false
*1 Shield Ground
*a No. 4 Floor Wire
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q1-1 (CBI) - Body ground and shield ground Power switch off 10 MΩ or higher
Q1-2 (CEI) - Body ground and shield ground Power switch off 10 MΩ or higher


HINT:

Visually inspect the No. 4 floor wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.


Result:
Proceed to
OK
NG




OK

8.CHECK HV BATTERY AREA

NG

9.CHECK NO. 4 FLOOR WIRE
8.CHECK HV BATTERY AREA
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 2 hybrid vehicle battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV BATTERY>REMOVAL


c.
A259732N01
2.147,0.828 2.634,1.12 0.487,0.292 2.289,0.885 2.584,1.066 0.295,0.182 10 z7

Disconnect connector z7 from the battery smart unit.


d.
A259720N04
1.563,0.781 1.229,1.75 false 2.042,0.781 2.375,1.75 false 2.333,1.76 2.479,1.917 0.146,0.156 10 true 1 1.156,1.76 1.302,1.917 0.146,0.156 10 true 2

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Power switch off 10 MΩ or higher
2 - Body ground Power switch off 10 MΩ or higher


Result:
Proceed to
OK
NG




OK

NG

10.CHECK HV BATTERY
9.CHECK NO. 4 FLOOR WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the No. 4 hybrid battery shield panel.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>REMOVAL


c.
A259723N06
0.281,0.604 0.771,0.896 0.49,0.292 1.688,0.177 2.177,0.469 0.49,0.292 0.417,0.656 0.667,0.854 0.25,0.198 10 true Q3 1.854,0.229 2.052,0.406 0.198,0.177 10 true Q2

Disconnect connector Q2 and connector Q3 of the No. 4 floor wire from the hybrid battery junction block assembly.

HINT:

Make sure that no foreign objects have entered or contaminated connector Q2 and Q3 of the No. 4 floor wire.



d.
A259725C02
0.896,0.063 1.385,0.354 0.49,0.292 1.667,0.073 2.156,0.365 0.49,0.292 1.135,0.771 1.135,1.167 false 1.906,0.771 1.906,1.167 false 2.031,1.698 1.542,1.698 false 0.094,0.063 0.354,0.24 0.26,0.177 10 false *a 1,0.125 1.198,0.302 0.198,0.177 10 false Q2 1.771,0.125 1.969,0.302 0.198,0.177 10 false Q3 0.979,1.177 1.281,1.365 0.302,0.188 10 false CBI 1.76,1.177 2.063,1.365 0.302,0.188 10 false CEI 1.344,1.615 1.542,1.781 0.198,0.167 10 false *1
*1 Shield Ground
*a No. 4 Floor Wire
(Hybrid Battery Junction Bock Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q3-1 (CEI) - Body ground and shield ground Power switch off 10 MΩ or higher
Q2-1 (CBI) - Body ground and shield ground Power switch off 10 MΩ or higher


HINT:

Visually inspect the No. 4 floor wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.


Result:
Proceed to
OK
NG




OK

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG

10.CHECK HV BATTERY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the hybrid battery junction block assembly.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HV RELAY ASSEMBLY>COMPONENTS


c.
A259720N04
1.563,0.781 1.229,1.75 false 2.042,0.781 2.375,1.75 false 2.333,1.76 2.479,1.917 0.146,0.156 10 true 1 1.156,1.76 1.302,1.917 0.146,0.156 10 true 2

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Power switch off 10 MΩ or higher
2 - Body ground Power switch off 10 MΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

NG

11.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A258636

Remove the upper inverter cover (generator cable side) and upper inverter cover (motor cable side) from the inverter with converter assembly.

HINT:

Make sure that no foreign objects have entered or contaminated the inverter with converter assembly.



c.
A258637C07
2.052,0.573 2.365,0.417 false 1.052,0.438 0.76,0.563 false 2.365,0.281 2.604,0.469 0.24,0.188 10 false *1 0.531,0.51 0.74,0.698 0.208,0.188 10 true *2
*1 Generator Cable
*2 Motor Cable


Disconnect the motor cable and generator cable from the inverter with converter assembly.


d.
A259710

Remove the connector cover assembly from the inverter with converter assembly.

HINT:

Make sure that no foreign objects have entered or contaminated the inverter with converter assembly.



e.
A259718C04
2.84,0.485 3.029,0.67 0.189,0.185 10 *1 1.865,0.57 2.811,0.57 false
*1 High Voltage Fuse


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
High voltage fuse terminal - Body ground Power switch off 1 MΩ or higher


Result:
Result Proceed to
NG A
OK B




A

REPLACE INVERTER WITH CONVERTER ASSEMBLY

B

REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

12.CHECK NO. 4 ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259733C01
1.792,1.26 2.042,1.458 0.25,0.198 0.979,0.271 1.229,0.219 false 1.281,0.146 1.594,0.302 0.313,0.156 10 *1 1.823,1.292 2.135,1.49 0.313,0.198 10 G1
*1 Green Lock


Disconnect connector G1 of the No. 4 engine wire (air conditioning harness) from the compressor with motor assembly.


c.
A260188C48
0.698,1.302 1.042,1.552 0.344,0.25 1.135,1.917 1.583,1.51 false 2.271,1.906 1.885,1.51 false 2.073,0.938 2.427,0.76 false 2.479,0.698 2.792,0.854 0.313,0.156 10 false *1 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.781,1.354 1.021,1.531 0.24,0.177 10 false G2 0.708,1.875 1.104,2.042 0.396,0.167 10 false ACPE 2.354,1.865 2.75,2.031 0.396,0.167 10 false ACPB
*1 Shield Ground
*a No. 4 Engine Wire (Air Conditioning Harness)
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
G2-1 (ACPE) - Body ground and shield ground Power switch off 10 MΩ or higher
G2-2 (ACPB) - Body ground and shield ground Power switch off 10 MΩ or higher


Result:
Proceed to
OK
NG




OK

GO TO AIR CONDITIONING SYSTEM (P0AA6-611)

NG

REPLACE NO. 4 ENGINE WIRE

13.CHECK HIGH VOLTAGE DIRECT CURRENT AREA
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259710

Remove the connector cover assembly from the inverter with converter assembly.

HINT:

Make sure that no foreign objects have entered or contaminated the inverter with converter assembly.



c.
A259712N04
1.5,0.865 1.99,1.156 0.49,0.292 1.667,0.917 1.927,1.094 0.26,0.177 10 true Q1

Disconnect connector Q1 of the No. 4 floor wire from the inverter with converter assembly.

HINT:

Make sure that no foreign objects have entered or contaminated connector Q1 of the No. 4 floor wire.



d.
A259783C04
0.083,0.025 0.355,0.224 0.272,0.199 10 *a 0.503,1.077 0.99,1.369 0.487,0.292 0.628,1.134 0.831,1.315 0.203,0.182 10 Q1 0.643,1.713 0.951,1.894 0.308,0.181 10 CBI 2.272,1.713 2.58,1.894 0.308,0.181 10 CEI 2.519,0.869 2.753,1.048 0.233,0.179 10 *1 1.342,1.423 0.976,1.788 false 1.853,1.423 2.218,1.788 false 2.144,1.07 2.497,0.966 false
*1 Shield Ground
*a No. 4 Floor Wire
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q1-1 (CBI) - Body ground and shield ground Power switch off 10 MΩ or higher
Q1-2 (CEI) - Body ground and shield ground Power switch off 10 MΩ or higher


HINT:

Visually inspect the No. 4 floor wire for damage. If there is any damage, then this is the likely cause of low insulation resistance.


Result:
Proceed to
OK
NG




OK

14.CHECK NO. 4 ENGINE WIRE

NG

9.CHECK NO. 4 FLOOR WIRE
14.CHECK NO. 4 ENGINE WIRE
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.
A259717N02
0.698,1.49 1.188,1.781 0.49,0.292 0.854,1.531 1.083,1.74 0.229,0.208 10 true G2

Disconnect connector G2 of the No. 4 engine wire (air conditioning harness) from the inverter with converter assembly.


c.
A260188C48
0.698,1.302 1.042,1.552 0.344,0.25 1.135,1.917 1.583,1.51 false 2.271,1.906 1.885,1.51 false 2.073,0.938 2.427,0.76 false 2.479,0.698 2.792,0.854 0.313,0.156 10 false *1 0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 0.781,1.354 1.021,1.531 0.24,0.177 10 false G2 0.708,1.875 1.104,2.042 0.396,0.167 10 false ACPE 2.354,1.865 2.75,2.031 0.396,0.167 10 false ACPB
*1 Shield Ground
*a No. 4 Engine Wire (Air Conditioning Harness)
(Inverter with Converter Assembly Side)


Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
G2-1 (ACPE) - Body ground and shield ground Power switch off 3 MΩ or higher
G2-2 (ACPB) - Body ground and shield ground Power switch off 3 MΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE INVERTER WITH CONVERTER ASSEMBLY

NG

12.CHECK NO. 4 ENGINE WIRE