Home › Engine / Hybrid System › 2AR-FXE ENGINE MECHANICAL › ENGINE UNIT
RM2040EQ _51 Engine / Hybrid System _014693 2AR-FXE ENGINE MECHANICAL _0074906 ENGINE UNIT A

2AR-FXE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE ENGINE COVER JOINT

a.
A259127

Remove the 3 engine cover joints.


Hide 89615 3.REMOVE KNOCK CONTROL SENSOR

Hide 89422 4.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 83530 5.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 11101J 6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 11102A 7.REMOVE CAMSHAFT POSITION SENSOR

Hide 12108 8.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.


Hide 12108A 9.REMOVE OIL FILLER CAP GASKET

a.

Remove the oil filler cap gasket from the oil filler cap sub-assembly.


Hide 11301K 10.REMOVE CRANKSHAFT POSITION SENSOR

Hide 12204 11.REMOVE VENTILATION VALVE SUB-ASSEMBLY

Hide 12205 12.REMOVE VENTILATION CASE SUB-ASSEMBLY

a.
A210185

Remove the 8 bolts and 2 nuts.


b.
A210186

Remove the ventilation case by prying between the ventilation case and cylinder block with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and ventilation case.


HINT:

Tape the screwdriver tip before use.



Hide 12215 13.REMOVE SEPARATOR CASE

a.
A210188

Remove the 2 bolts, separator case and gasket.


Hide 13471 14.REMOVE CRANKSHAFT PULLEY

a.
A293510
1.323,0.99 0.583,0.865 0.583,0.865 1.219,0.635 true 0.552,0.271 0.865,0.427 0.313,0.156 10 false *a 2.417,1.677 2.729,1.833 0.313,0.156 10 false *b 0.26,0.781 0.719,0.979 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, hold the crankshaft pulley and loosen the pulley bolt. Further loosen the bolt until 2 or 3 threads are screwed into the crankshaft.

SST
09213-54015  
09330-00021  

HINT:

SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650(2 pcs)



b.
A195874
2.25,0.208 2.542,0.677 false 1.813,0.875 1.469,1.083 false 1.313,1.094 1.729,1.344 0.417,0.25 10 false SST 2.063,0.115 2.281,0.302 0.219,0.188 10 false *1 0.333,1.979 0.615,2.188 0.281,0.208 10 false *a 1.219,3.177 1.49,3.354 0.271,0.177 10 false *b
*1 Pulley Bolt
*a Hold
*b Turn


Using SST and the pulley bolt, remove the crankshaft pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05011)

HINT:

Apply a lubricant to the threads and end of SST.



Hide 11201 15.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A259132

Remove the 16 bolts, 3 seal washers, cylinder head cover sub-assembly and cylinder head cover gasket.


b.
A259133

Remove the 2 gaskets from the camshaft bearing caps.


Hide 16.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A260357

Using an E6 "TORX" socket wrench, remove the 3 stud bolts from the cylinder head cover sub-assembly.


Hide 11193 17.REMOVE SPARK PLUG TUBE GASKET

a.
A259134
1.277,0.0 1.448,0.177 0.171,0.177 10 *1 1.018,0.971 1.165,0.086 1.165,0.086 1.271,0.086 false
*1 Tape


Using a screwdriver, pry out the 4 spark plug tube gaskets.

NOTICE:

Be careful not to damage the cylinder head cover.


HINT:

Tape the screwdriver tip before use.



Hide 12315A 18.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11302 19.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 20.REMOVE OIL PUMP RELIEF VALVE PLUG

a.
A196859

Using a 14 mm hexagon wrench, remove the oil pump relief valve plug and gasket.


Hide 11324 21.REMOVE TIMING CHAIN COVER PLATE

a.
A196860

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 11301C 22.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 23.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13540 25.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 26.REMOVE CHAIN TENSIONER SLIPPER

Hide 13506 27.REMOVE CHAIN SUB-ASSEMBLY

a.

Remove the chain sub-assembly.


Hide 13561 28.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13521 29.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A196881

Remove the crankshaft timing sprocket from the crankshaft.


Hide 13050 30.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13523 31.REMOVE CAMSHAFT TIMING SPROCKET

Hide 11103 32.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 15678A 34.REMOVE OIL CONTROL VALVE FILTER

a.
A196915

Remove the oil control valve filter from the No. 1 camshaft bearing cap.


Hide 11811 36.REMOVE NO. 1 CAMSHAFT BEARING

a.
A196916

Remove the No. 1 camshaft bearing from the No. 1 camshaft bearing cap.


Hide 11821 37.REMOVE NO. 2 CAMSHAFT BEARING

a.
A196917

Remove the No. 2 camshaft bearing from the camshaft housing sub-assembly.


Hide 38.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A241922

Using an E8 "TORX" socket wrench, remove the stud bolt from the camshaft housing sub-assembly.


Hide 11151A 39.REMOVE CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


a.
A241923

Remove the 10 camshaft bearing cap setting ring pins from the camshaft housing sub-assembly.


Hide 11114A 40.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.


a.
A241924

Remove the 2 straight pins from the camshaft housing sub-assembly.


Hide 13801 41.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 42.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 44.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11445 46.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A196938

Remove the cylinder block water jacket spacer from the cylinder block.

NOTICE:

Be sure to remove the water jacket spacer. If it is not removed, it may fall and become damaged when the cylinder block is inverted.



Hide 12101A 48.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket from the oil pan sub-assembly.


Hide 12101 49.REMOVE OIL PAN SUB-ASSEMBLY

a.
A210204
0.76,1.198 1.771,1.417 1.771,1.417 1.49,1.833 false 1.823,1.375 2.063,1.521 0.24,0.146 10 false *1
*1 Nut


Remove the 11 bolts and 2 nuts.


b.
A118769

Insert the blade of an oil pan seal cutter between the oil pan and stiffening crankcase, cut off the applied sealer and remove the oil pan.

NOTICE:
·

Be careful not to damage the stiffening crankcase contact surface of the oil pan.

·

Be careful not to damage the stiffening crankcase flange.




Hide 15104 50.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A196919

Remove the 3 bolts, oil strainer sub-assembly and gasket.


Hide 12121 51.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A196920

Remove the 5 bolts and No. 1 oil pan baffle plate.


Hide 13411 52.INSPECT CRANKSHAFT BACKLASH

a.
A196931

Using a dial indicator, measure the backlash of the crankshaft and balance shaft as shown in the illustration.

Standard backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


Maximum backlash:

0.20 mm (0.00787 in.)


If the backlash is more than the maximum, replace the engine balancer assembly.


Hide 13620B 53.REMOVE ENGINE BALANCER ASSEMBLY

a.
A196921

Remove the 7 bolts and engine balancer assembly.

NOTICE:

Do not disassemble the engine balancer.



Hide 54.INSPECT NO. 1 BALANCE SHAFT THRUST CLEARANCE

Hide 55.INSPECT NO. 2 BALANCE SHAFT THRUST CLEARANCE

Hide 11420 56.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A196933

Remove the 7 bolts.


b.
A196934
0.031,0 0.281,0.26 0.25,0.26 10 false *a 0.031,2.135 0.375,2.438 0.344,0.302 10 false *b
*a LH Side
*b RH Side


Using a screwdriver, remove the stiffening crankcase by prying between the stiffening crankcase and cylinder block at the places shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and stiffening crankcase.


HINT:

Tape the screwdriver tip before use.



Hide 57.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A241935

Using an E5 and E8 "TORX" socket wrench, remove the 3 stud bolts from the stiffening crankcase assembly.


Hide 58.REMOVE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


a.
A241936

Remove the 2 ring pins from the stiffening crankcase assembly.


Hide 11401L 59.REMOVE REAR ENGINE OIL SEAL

a.
A196937

Remove the rear engine oil seal from the cylinder block.