Home › Drivetrain › P314 HYBRID TRANSMISSION / TRANSAXLE › SHIFT LEVER
RM2040EQ _52 Drivetrain _014701 P314 HYBRID TRANSMISSION / TRANSAXLE _0074952 SHIFT LEVER A

P314 HYBRID TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSTALLATION  


PROCEDURE

Hide 33525 1.INSTALL SHIFT LEVER SUPPORT

a.
C244185N02
3.156,0.719 3.292,0.896 0.135,0.177 10 true 1 0.802,1.667 0.927,1.854 0.125,0.188 10 true 2 1.74,0.031 1.875,0.219 0.135,0.188 10 false 3 1.219,0.385 1.375,0.552 0.156,0.167 10 true 4

Install the shift lever support with the 4 bolts in the sequence shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 33560C 2.INSTALL LOWER SHIFT LEVER ASSEMBLY

NOTICE:

Check that the shift lever position sensor and the shift lever are in neutral.


a.
C253634N01
1.625,0.156 1.76,0.323 0.135,0.167 10 false 1 1.063,1.625 1.198,1.813 0.135,0.188 10 true 2 1.125,0.771 1.26,0.938 0.135,0.167 10 false 3 2.719,0.625 2.896,0.802 0.177,0.177 10 true 4

Install the lower shift lever assembly with the 4 bolts in the sequence shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Connect the 3 clamps and connector.


c.
C194520C19
2.25,2.573 2.594,2.573 false 1.958,1.75 2.094,1.531 2.094,1.531 2.198,1.531 false 1.635,0.906 1.823,1.083 0.188,0.177 10 true *a 1.792,1.365 1.979,1.542 0.188,0.177 10 false *a 2.469,0.875 2.656,1.052 0.188,0.177 10 false *b 2.229,1.458 2.417,1.635 0.188,0.177 10 false *1 2.229,2.333 2.417,2.51 0.188,0.177 10 false *b 2.615,2.49 2.802,2.667 0.188,0.177 10 false *2
*1 Slider
*2 Lock Piece
*a Slide
*b Pull


Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.


d.
C241614C05
1.281,2.24 1.406,2.042 1.406,2.042 1.542,2.042 false 1.583,1.958 1.875,2.146 0.292,0.188 10 false *1
*1 Lock Piece


Install the end of the transmission control cable to the shift lever assembly.

NOTICE:
·

Check that the lock piece is pulled up.

·

Install the cable end all the way to the base of the pin.




e.

Push the lock piece into the adjuster case.

NOTICE:
·

Check that the shift lever position sensor and the shift lever are in neutral.

·

Securely push in the lock piece until the slider lock is engaged.




Hide 58861B 3.INSTALL NO. 1 CONSOLE BOX DUCT

a.

Install the No. 1 console box duct to the lower shift lever assembly with the clip.


Hide 58995A 4.INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET

a.

Install the No. 1 console box mounting bracket to the lower shift lever assembly with the screw.


Hide 58543B 5.INSTALL FLOOR CARPET BRACKET RH

Hide 58817A 7.INSTALL FRONT NO. 2 CONSOLE BOX INSERT

Hide 58804A 8.INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

Hide 55303B 10.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 55607 11.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55317A 12.INSTALL INSTRUMENT SIDE PANEL RH

Hide 62311B 13.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 62111A 14.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

Hide 67913 15.INSTALL FRONT DOOR SCUFF PLATE RH

Hide 16.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 53601 17.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55318C 18.INSTALL INSTRUMENT SIDE PANEL LH

Hide 62312B 19.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62112A 20.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 67914 21.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 22.INSTALL REAR CONSOLE BOX ASSEMBLY