Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT
RM2040EQ _58 Vehicle Interior _014730 HEATING / AIR CONDITIONING _0075126 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


PROCEDURE

Hide 1.INSTALL AIR CONDITIONING UNIT ASSEMBLY

a.

Install the air conditioning unit assembly to the instrument panel reinforcement assembly with the 3 bolts.

E250070E02
1.156,0.927 1.031,1.281 false 4.656,0.885 4.833,1.24 false 5.385,0.854 5.74,1.177 0.354,0.323 10 false (1) 4.792,1.24 5.094,1.51 0.302,0.271 10 true (3) 0.948,1.281 1.25,1.583 0.302,0.302 10 false (2)

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration to install the air conditioning unit assembly.



Hide 2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT

NOTICE:
·

Be sure to support the air conditioning unit assembly when installing it because failure to do so may cause the bracket of the air conditioning unit assembly to break.

·

When installing the air conditioning unit, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.

Engage the 3 guides and temporarily install the instrument panel reinforcement assembly with air conditioning unit as shown in the illustration.

E250071


b.

Install the instrument panel reinforcement assembly with the 3 bolts <A> and 2 new bolts <B> in the order shown in the illustration.

E250072C01
3.083,1.271 2.844,1.354 false 3.365,1.135 3.552,0.938 false 3.49,1.49 3.604,1.396 false 6.573,2.427 6.281,3.323 6.281,3.323 6.51,2.917 false 6.281,3.323 6.594,2.604 false 2.677,1.281 2.99,1.542 0.313,0.26 10 false *1 3.583,0.802 3.938,1.063 0.354,0.26 10 false *2 3.604,1.271 3.979,1.521 0.375,0.25 10 false *3 1.917,0.333 2.333,0.667 0.417,0.333 10 false *a 2.833,0.333 3.167,0.583 0.333,0.25 10 false *b 3.833,0.333 4.167,0.583 0.333,0.25 10 false *c 4.833,0.333 5.25,0.583 0.417,0.25 10 false *d 6.906,2.26 7.156,2.552 0.25,0.292 10 false (1) 6.917,2.458 7.156,2.708 0.24,0.25 10 false (2) 6.854,2.771 7.156,3.063 0.302,0.292 10 false (3) 0.042,3.406 0.427,3.688 0.385,0.281 10 false (4) 0.094,3.625 0.479,3.885 0.385,0.26 10 false (5) 6.125,3.344 6.594,3.635 0.469,0.292 10 false <A> 0.198,3.24 0.698,3.542 0.5,0.302 10 false <B> 0.313,3.771 0.823,4.063 0.51,0.292 10 false <B> 5.51,3.927 5.844,4.125 0.333,0.198 10 true <C>
*1 Movable Collar *2 Body
*3 Instrument Panel Reinforcement - -
*a Step 1 *b Step 2
*c Step 3 *d Step 4


Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)

NOTICE:

Tighten the bolts in the order shown in the illustration to install the reinforcement assembly.



c.

Install the instrument panel reinforcement assembly with air conditioning unit with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


d.

Install the bolt.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


e.

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


f.

Connect the connector holder with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


g.

Install the 3 bolts and connect the 3 earth wires.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.

Connect the connector.


i.

Pass the cooler drain hose through the vehicle securely.

NOTICE:

Connect the cooler drain hose firmly to prevent water leaks.



j.

Engage each clamp.


k.

Engage the claw to connect the airbag connector as shown in the illustration.

E227176


l.
E227174C09
2.073,2.677 2.458,2.948 false 2.51,2.896 2.813,3.177 0.302,0.281 10 false *1
*1 Retainer


Engage the 2 claws to lock the retainer as shown in the illustration.


m.
E230617C03
0.177,0.156 0.646,0.438 0.469,0.281 10 false *1
*1 Airbag Sensor Assembly


Engage each clamp.


n.

Connect each connector.


o.

Connect the connector to the airbag sensor assembly as shown in the illustration.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.



p.
E230620

Engage the 3 clamps to close the 3 clamps as shown in the illustration.


q.

Connect the connector.


r.

Install the bolt.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


s.

for 10 Speakers:

i.

Engage the 3 clamps.



Hide 3.INSTALL FRONT LOWER PANEL PACKING

a.
E247264

Install the 2 front lower panel packings.


Hide 55458A 4.INSTALL INSTRUMENT PANEL SAFETY PAD CAP

a.

Install the 5 new instrument panel safety pad caps.

E277020C01
0.708,0.177 1.083,0.417 0.375,0.24 12 false *A 4.042,0.177 4.417,0.417 0.375,0.24 12 false *B
*A for Driver Side *B for Passenger Side



Hide 55306B 5.INSTALL INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.

Install the screw.


b.

Install the 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Install the instrument panel to cowl brace sub-assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.

Connect the earth wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Engage each clamp.


f.

Connect the connector.


Hide 55307E 6.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

Install the screw.


b.

Install the 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


c.

Install the No. 2 instrument panel brace sub-assembly with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.

Connect the earth wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Engage each clamp.


f.

Connect the connector.


Hide 88625Q 7.INSTALL ROOM TEMPERATURE SENSOR (COOLER THERMISTOR)

a.

Connect the connector and cooler thermistor hose to install the room temperature sensor (cooler thermistor).


Hide 58861B 8.INSTALL NO. 1 CONSOLE BOX DUCT

a.

Install the No. 1 console box duct with the clip.


Hide 87212F 9.INSTALL REAR NO. 2 AIR DUCT

a.

Engage the 2 claws to install the rear No. 2 air duct.


Hide 58544A 10.INSTALL FLOOR CARPET BRACKET LH

a.

Engage the 2 guides.


b.

Install the floor carpet bracket LH with the 2 clips.


c.
E230502

Engage the guide to install the floor carpet to the original position as shown in the illustration.


Hide 87212 11.INSTALL REAR NO. 1 AIR DUCT

a.

Engage the 2 claws to install the rear No. 1 air duct.


Hide 58543B 12.INSTALL FLOOR CARPET BRACKET RH

a.

Engage the 2 guides.


b.

Install the floor carpet bracket RH with the 2 clips.


c.
E230496

Engage the guide to install the floor carpet to the original position as shown in the illustration.


Hide 58569D 13.INSTALL FRONT FLOOR CAUTION PLATE COVER

a.
E234874

Engage the guide and claw to install the front floor caution plate cover.


Hide 77306 14.CONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

a.
E230494

Engage the guide to connect the fuel lid lock open lever sub-assembly as shown in the illustration.


b.

Install the screw.


Hide 58521B 15.INSTALL FLOOR CARPET HOOK

a.

Engage the 6 claws to install the 6 floor carpet hooks.


b.

Engage the 6 guides.


Hide 85940 16.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY (w/ Rain Sensor)

Hide 88650N 17.INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

Hide 82730 18.INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

Hide 89681A 19.INSTALL POWER MANAGEMENT CONTROL ECU

Hide 21.INSTALL STEERING POST ASSEMBLY

Hide 22.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

Hide 23.INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers)

Hide 86183D 24.INSTALL AUDIO AMPLIFIER COVER (for 10 Speakers)

Hide 26.INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)

Hide 27.INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)

HINT:

Use the same procedure as for the RH side.


Hide 88710E 28.CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

a.

Remove the vinyl tape from the pipe.


b.

Sufficiently apply compressor oil to a new O-ring and fitting surface of the air conditioner tube and accessory assembly.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the air conditioner tube and accessory assembly.


d.

Connect the air conditioner tube and accessory assembly.


Hide 88704 29.CONNECT SUCTION HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the pipe.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.

Compressor oil:

ND-OIL 11 or equivalent



c.

Install the O-ring to the suction hose sub-assembly.


d.
E230489

Rotate the hook connector in the direction indicated by the arrow in the illustration.


e.

Insert the pipe joint into the cooler expansion valve securely and tighten the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87245 30.CONNECT HEATER INLET WATER HOSE

a.

Using pliers, grip the claws of the clip and slide the clip to connect the inlet water hose.


Hide 87246 31.CONNECT HEATER OUTLET WATER HOSE

a.

Using pliers, grip the claws of the clip and slide the clip to connect the heater outlet water hose.


Hide 55702A 32.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 33.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 34.INSPECT FOR COOLANT LEAK (for Engine)

Hide 35.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR (for Engine)

Hide 36. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT