Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER
RM2040EQ _53 Suspension _014706 REAR SUSPENSION _0074975 REAR SUSPENSION MEMBER A

REAR SUSPENSION  REAR SUSPENSION MEMBER  REMOVAL  


PROCEDURE

Hide 1.REMOVE REAR WHEELS

Hide 17420 2.REMOVE CENTER EXHAUST PIPE ASSEMBLY

Hide 58399B 3.REMOVE NO. 2 FLOOR UNDER COVER

Hide 58398H 4.REMOVE NO. 1 FLOOR UNDER COVER

Hide 48840A 5.SEPARATE REAR STABILIZER LINK ASSEMBLY LH

a.
C241264

Remove the nut and separate the rear stabilizer link assembly LH from the rear stabilizer bar.

If the ball joint turns together with the nut, use a hexagon wrench to hold the stud.


Hide 48830D 6.SEPARATE REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 7.REMOVE REAR STABILIZER BAR

Hide 17573A 8.REMOVE NO. 3 EXHAUST PIPE SUPPORT BRACKET

a.
C249432

Remove the 2 bolts and No. 3 exhaust pipe support bracket from the rear suspension member sub-assembly.


Hide 58219C 9.REMOVE REAR CENTER FLOOR END PLATE

a.
C251085

Remove the 2 bolts and rear center floor end plate from the rear suspension member sub-assembly.


Hide 48740F 10.SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 11.SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 12.SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 13.SEPARATE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51206A 14.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.
C249991
0.365,2.177 0.188,2.177 0.188,2.177 0.188,2.313 false 1.177,1.74 1.052,1.74 1.052,1.74 1.052,2.354 false 1.146,1.865 1.052,1.865 false 0.708,1.948 0.365,1.948 false 2.083,1.688 2.25,1.688 false 0.094,2.323 0.26,2.479 0.167,0.156 10 false *1 0.969,2.375 1.219,2.615 0.25,0.24 10 false *2 0.198,1.865 0.406,2.083 0.208,0.219 10 false *2 2.281,1.594 2.521,1.823 0.24,0.229 10 false *2
*1 Engine Lifter
*2 Attachment
V100155

Attachment Placement Location


Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

NOTICE:
·

Make sure to secure the rear suspension member sub-assembly to prevent it from dropping.

·

Use the attachments to keep the rear suspension member sub-assembly level.




b.

Remove the 2 bolts, 4 nuts, 2 rear suspension member lower stopper sub-assemblies and 2 rear suspension member lower stoppers.

C249990


c.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.



Hide 48740F 15.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 16.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 17.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 18.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51249 19.REMOVE REAR SUSPENSION MEMBER DAMPER

a.
C203221

Remove the 2 bolts and rear suspension member damper from the rear suspension member sub-assembly.


Hide 52272A 20.REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION LH

a.
C240553
1.49,0.76 1.896,0.76 1.896,0.76 1.896,0.969 false 1.521,0.969 2.104,0.969 false 1.688,1.24 2.135,1.24 false 2.146,0.896 2.521,1.115 0.375,0.219 10 false SST 2.167,1.167 2.552,1.375 0.385,0.208 10 false SST

Using SST and a press, remove the rear suspension member body mounting front cushion LH from the rear suspension member sub-assembly.

SST
09527-17011  
09950-60010  (09951-00320)
09950-70010  (09951-07100)


Hide 52271E 21.REMOVE REAR SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION RH

HINT:

Perform the same procedure as the LH side.


Hide 52275A 22.REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for LH Side)

a.
C240554
1.75,1.229 1.302,1.229 false 1.938,0.719 1.448,0.719 false 1.906,0.948 1.667,0.948 1.667,0.948 1.667,0.729 false 1.167,0.646 1.604,0.917 0.438,0.271 10 false SST 1.021,1.146 1.427,1.417 0.406,0.271 10 false SST

Using SST and a press, remove the rear suspension member body mounting rear cushion from the rear suspension member sub-assembly.

SST
09527-17011  
09950-60010  (09951-00320)
09950-70010  (09951-07100)


Hide 52275A 23.REMOVE REAR SUSPENSION MEMBER BODY MOUNTING REAR CUSHION (for RH Side)

HINT:

Perform the same procedure as the LH side.


Hide 24.REMOVE HOLE PLUG

a.
C248107

Remove the 2 hole plugs from the rear suspension member sub-assembly.