WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK
Release the parking brake.
Before releasing the parking brake, move the shift lever to P for safety.
When the parking brake is applied or the brake fluid level is low, the brake warning light / red (malfunction) comes on.
When the power switch is turned on (IG), check that the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction) and slip indicator lights come on until the power switch is turned on (READY).
If the skid control ECU stores any DTCs, the ABS warning, brake warning / red (malfunction), brake warning / yellow (minor malfunction) and slip indicator lights will come on.
If any of the indicators remains on or does not come on, proceed to troubleshooting for the light circuits listed below.
SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using the Intelligent Tester)
Before performing the master cylinder pressure sensor check, perform linear valve offset learning.
If the power switch is turned from on (IG) to on (ACC) or off during Test Mode (signal check), DTCs recorded during the sensor check will be cleared.
During Test Mode (signal check), the skid control ECU records all DTCs detected in the sensor check. By performing Test Mode (signal check), the codes are cleared as the normal condition for each item is confirmed. The remaining codes are the codes where an abnormality was found.
Procedure to enter Test Mode
Turn the power switch off.
Check that the steering wheel is centered.
Check that the parking brake is released.
Check that the shift lever is in P.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Switch the skid control ECU to Test Mode using the intelligent tester. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.
| Tester Display |
|---|
| Signal Check |
Check that the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.
If the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights do not blink, inspect the ABS warning, brake warning / yellow (minor malfunction) and slip indicator light circuits.
Check the ABS sensors.
Check that the ABS warning light is blinking in the Test Mode pattern before performing the following ABS sensor checks.
Acceleration Sensor Check
Keep the vehicle stationary on a level surface for 2 second or more.
The acceleration sensor check can be performed by following the master cylinder pressure sensor check procedure below.
Master Cylinder Pressure Sensor Check
Before performing the master cylinder pressure sensor check, perform linear valve offset learning.
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force greater than 98 N (10 kgf, 22.0 lbf) for 1 second.
Check that the ABS warning light stays on for 3 seconds.
Confirm that the ABS warning light comes on.
While the ABS warning light stays on, continue to depress the brake pedal with a force of 98 N (10 kgf, 22.0 lbf) or more.
The ABS warning light comes on for 3 seconds every time the preceding brake pedal operation is performed.
Speed Sensor Check
Before performing the speed sensor check, complete the acceleration sensor and master cylinder pressure sensor checks.
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
The sensor check may not complete if wheelspin occurs.
The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.
Stop the vehicle.
The speed sensor check may not complete if the speed sensor check is started while turning the steering wheel or spinning the wheels.
After the ABS warning light goes off, if vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
If the sensor check has not completed, the ABS warning light will blink while the vehicle is being driven and the ABS will not operate.
End of Sensor Check
When the sensor checks have completed, the ABS warning light goes off while driving, and blinks in the Test Mode pattern while the vehicle is stopped.
When the acceleration sensor, speed sensor and master cylinder pressure sensor checks complete, the sensor check is complete.
If the sensor checks have not completed, the ABS warning light will keep blinking while the vehicle is being driven, and the ABS will not operate.
Reading Sensor Check DTCs
Read the DTC(s) by following the intelligent tester screen.
If only DTCs other than Test Mode sensor check DTCs are displayed, repair the malfunction and clear the DTCs.
If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunction, clear the DTCs, and perform the Test Mode inspection again.
See "Sensor Check DTCs".
Turn the power switch off and disconnect the intelligent tester.
Sensor Check DTCs
| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| C1271 | Low Output Signal of Front Speed Sensor RH | ·
Front speed sensor RH ·
Sensor installation ·
Front speed sensor rotor RH (Front drive outboard joint shaft assembly RH) |
| C1272 | Low Output Signal of Front Speed Sensor LH | ·
Front speed sensor LH ·
Sensor installation ·
Front speed sensor rotor LH (Front drive outboard joint shaft assembly LH) |
| C1273 | Low Output Signal of Rear Speed Sensor RH | ·
Rear speed sensor RH ·
Sensor installation ·
Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) |
| C1274 | Low Output Signal of Rear Speed Sensor LH | ·
Rear speed sensor LH ·
Sensor installation ·
Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) |
| C1275 | Abnormal Change in Output Signal of Front Speed Sensor RH | ·
Front speed sensor RH ·
Front speed sensor rotor RH (Front drive outboard joint shaft assembly RH) |
| C1276 | Abnormal Change in Output Signal of Front Speed Sensor LH | ·
Front speed sensor LH ·
Front speed sensor rotor LH (Front drive outboard joint shaft assembly LH) |
| C1277 | Abnormal Change in Output Signal of Rear Speed Sensor RH | ·
Rear speed sensor RH ·
Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) |
| C1278 | Abnormal Change in Output Signal of Rear Speed Sensor LH | ·
Rear speed sensor LH ·
Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) |
| C1279 | Acceleration Sensor Output Voltage Malfunction | ·
Sensor installation ·
Yaw rate and acceleration sensor (Airbag sensor assembly) |
| C1281 | Master Cylinder Pressure Sensor Output Malfunction | ·
Stop light switch assembly ·
Regulator pressure sensor (Brake booster with master cylinder assembly) |
| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| C1346 | Stroke Sensor Zero Point Learning Malfunction | ·
Brake pedal stroke sensor assembly ·
Brake pedal stroke sensor assembly circuit |
The codes in this table are output only in Test Mode (signal check).
SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When not Using the Intelligent Tester)
Before performing the master cylinder pressure sensor check, perform linear valve offset learning.
If the power switch is turned from on (IG) to on (ACC) or off during Test Mode (signal check), DTCs recorded during the sensor check will be cleared.
During Test Mode (signal check), the skid control ECU records all DTCs detected in the sensor check. By performing Test Mode (signal check), the codes are cleared as the normal condition for each item is confirmed. The remaining codes are the codes where an abnormality was found.
Procedure to enter Test Mode
Turn the power switch off.
Check that the steering wheel is centered.
Check that the parking brake is released.
Check that the shift lever is in P.
| *a | Front view of DLC3 |
Using SST, connect terminals TS and CG of the DLC3.
Turn the power switch on (IG).
Check that the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.
If the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights do not blink, inspect the TS and CG terminal circuit and ABS warning, brake warning / yellow (minor malfunction) and slip indicator light circuits.
Check the ABS sensors.
Check that the ABS warning light is blinking in the Test Mode pattern before performing the following ABS sensor checks.
Acceleration Sensor Check
Keep the vehicle stationary on a level surface for 2 second or more.
The acceleration sensor check can be performed by following the master cylinder pressure sensor check procedure below.
Master Cylinder Pressure Sensor Check
Before performing the master cylinder pressure sensor check, perform linear valve offset learning.
Leave the vehicle in a stationary condition and release the brake pedal for 1 second or more, and quickly and continuously depress the brake pedal with a force greater than 98 N (10 kgf, 22.0 lbf) for 1 second.
Check that the ABS warning light stays on for 3 seconds.
Confirm that the ABS warning light comes on.
While the ABS warning light stays on, continue to depress the brake pedal with a force of 98 N (10 kgf, 22.0 lbf) or more.
The ABS warning light comes on for 3 seconds every time the preceding brake pedal operation is performed.
Speed Sensor Check
Before performing the speed sensor check, complete the acceleration sensor and master cylinder pressure sensor checks.
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.
The sensor check may not complete if wheelspin occurs.
The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.
Stop the vehicle.
The speed sensor check may not complete if the speed sensor check is started while turning the steering wheel or spinning the wheels.
After the ABS warning light goes off, if vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
If the sensor check has not completed, the ABS warning light will blink while the vehicle is being driven and the ABS will not operate.
End of Sensor Check
When the sensor checks have completed, the ABS warning light goes off while driving, and blinks in the Test Mode pattern while the vehicle is stopped.
When the acceleration sensor, speed sensor and master cylinder pressure sensor checks complete, the sensor check is complete.
If the sensor checks have not completed, the ABS warning light will keep blinking while the vehicle is being driven, and the ABS will not operate.
Reading Sensor Check DTCs
| *a | Front view of DLC3 |
Using SST, connect terminals TC and CG of the DLC3.
Count the number of blinks of the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights.
How to read DTCs:
Diagnostic trouble codes are represented by the number of blinks of a warning light. For example, code 21 would be shown by 2 blinks, a pause of 1.5 seconds, and then 1 blink.
If one code is detected:
The light repeats the same code after a pause of 4 seconds.
If multiple codes are detected:
The light outputs one code after another with a 2.5-second pause between each code. When all codes have been output, there is a 4-second pause and then the light begins to output the codes again.
If only DTCs other than Test Mode sensor check DTCs are displayed, repair the malfunctions and clear the DTCs.
If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunctions, clear the DTCs, and perform the Test Mode inspection again.
If more than 1 malfunction is detected at the same time, the lowest numbered code will be displayed first.
See "Sensor Check DTCs".
After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3 and turn the power switch off.
If the power switch is not turned off and back on (IG) after SST is removed from the DLC3, the previous Test Mode will continue.
If the power switch is turned back on (IG) with terminals TS and CG connected, the previous Test Mode will continue.
Sensor Check DTCs
| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| 71 | Low Output Signal of Front Speed Sensor RH | ·
Front speed sensor RH ·
Sensor installation ·
Front speed sensor rotor RH (Front drive outboard joint shaft assembly RH) |
| 72 | Low Output Signal of Front Speed Sensor LH | ·
Front speed sensor LH ·
Sensor installation ·
Front speed sensor rotor LH (Front drive outboard joint shaft assembly LH) |
| 73 | Low Output Signal of Rear Speed Sensor RH | ·
Rear speed sensor RH ·
Sensor installation ·
Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) |
| 74 | Low Output Signal of Rear Speed Sensor LH | ·
Rear speed sensor LH ·
Sensor installation ·
Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) |
| 75 | Abnormal Change in Output Signal of Front Speed Sensor RH | ·
Front speed sensor RH ·
Front speed sensor rotor RH (Front drive outboard joint shaft assembly RH) |
| 76 | Abnormal Change in Output Signal of Front Speed Sensor LH | ·
Front speed sensor LH ·
Front speed sensor rotor LH (Front drive outboard joint shaft assembly LH) |
| 77 | Abnormal Change in Output Signal of Rear Speed Sensor RH | ·
Rear speed sensor RH ·
Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH) |
| 78 | Abnormal Change in Output Signal of Rear Speed Sensor LH | ·
Rear speed sensor LH ·
Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH) |
| 79 | Acceleration Sensor Output Voltage Malfunction | ·
Sensor installation ·
Yaw rate and acceleration sensor (Airbag sensor assembly) |
| 81 | Master Cylinder Pressure Sensor Output Malfunction | ·
Stop light switch assembly ·
Regulator pressure sensor (Brake booster with master cylinder assembly) |
| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| 71 | Stroke Sensor Zero Point Learning Malfunction | ·
Brake pedal stroke sensor assembly ·
Brake pedal stroke sensor assembly circuit |
The codes in this table are output only in Test Mode (signal check).