Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › 2012.02–2015.04
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the brake warning light / red (malfunction) remains on:

·

The skid control ECU (brake booster with master cylinder assembly) connector is disconnected from the brake booster with master cylinder assembly.

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

EBD operation has been disabled.


WIRING DIAGRAM

C249763E09
0.646,0.531 1.094,0.677 0.448,0.146 10 false CANH 0.656,1.083 1.208,1.292 0.552,0.208 10 false CANL 4.479,2.729 5.115,2.958 0.635,0.229 10 false CANH 4.49,2.052 5.104,2.302 0.615,0.25 10 false CANL 6.219,2.75 6.833,2.979 0.615,0.229 10 false CA1H 6.219,2.052 6.75,2.313 0.531,0.26 10 false CA1L 1.188,0.552 1.583,0.729 0.396,0.177 10 false I13 1.198,0.333 1.417,0.563 0.219,0.229 10 false 14 1.188,1.094 1.667,1.385 0.479,0.292 10 false I13 1.198,0.865 1.5,1.125 0.302,0.26 10 false 13 4.969,1.958 5.333,2.229 0.365,0.271 10 false 15 4.969,2.635 5.25,2.875 0.281,0.24 10 false 16 6.219,3.833 6.583,4.042 0.365,0.208 10 false IG1 6.219,4.479 6.75,4.729 0.531,0.25 10 false LBL 5.938,4.375 6.25,4.552 0.313,0.177 10 false 36 2.292,3.323 2.75,3.573 0.458,0.25 10 false I18 2.552,3.313 4.667,3.563 2.115,0.25 10 false Combination Meter Assembly 1.99,3.813 3.583,4.021 1.594,0.208 10 false from IG1 NO. 2 Relay 4.365,3.99 5.5,4.219 1.135,0.229 10 false ECU-IG1 NO. 1 4.958,8.156 7,8.729 2.042,0.573 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 0.521,5.677 1,5.885 0.479,0.208 10 false PKB 0.448,5.896 0.75,6.125 0.302,0.229 10 false 12 0.073,8.167 1.74,8.646 1.667,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 1.198,7.146 1.5,7.375 0.302,0.229 10 false 3D 1.219,6.927 1.594,7.125 0.375,0.198 10 false 20 3.135,5.219 3.333,5.552 0.198,0.333 10 false 2 1.969,7.031 2.083,7.25 0.115,0.219 10 false 1 1.74,5.219 2,5.458 0.26,0.24 10 false 1 1.26,5.885 1.667,6.073 0.406,0.188 10 false A31 1.563,5.885 3.667,6.49 2.104,0.604 10 false Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Assembly) 1.552,7.5 1.896,7.688 0.344,0.188 10 false A42 1.833,7.49 3.167,7.917 1.333,0.427 10 false Parking Brake Switch Assembly 6.219,5.323 6.75,5.573 0.531,0.25 10 false GND 6.219,5.76 6.75,6.042 0.531,0.281 10 false GND2 6.219,6.208 6.833,6.469 0.615,0.26 10 false GND3 6.219,6.656 6.833,6.875 0.615,0.219 10 false GND4 6.219,7.094 6.635,7.24 0.417,0.146 10 false GND5 6.219,7.563 6.802,7.875 0.583,0.313 10 false GND6 4.656,8.167 5.083,8.406 0.427,0.24 10 false A28 1.927,5.219 2.167,5.469 0.24,0.25 10 false + 2.927,5.219 3.083,5.417 0.156,0.198 10 false E 5.938,5.208 6.25,5.458 0.313,0.25 10 false 28 5.938,5.656 6.25,5.885 0.313,0.229 10 false 27 5.938,6.094 6.333,6.302 0.396,0.208 10 false 26 5.938,6.552 6.333,6.802 0.396,0.25 10 false 25 5.938,6.99 6.25,7.208 0.313,0.219 10 false 24 5.938,7.458 6.25,7.656 0.313,0.198 10 false 23 5.938,3.729 6.333,3.958 0.396,0.229 10 false 16 5.938,2.646 6.417,2.969 0.479,0.323 10 false 37 5.938,1.958 6.25,2.229 0.313,0.271 10 false 38 2.146,7.031 2.417,7.219 0.271,0.188 10 false +

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK DTC
a.

Check if ABS, VSC and/or electronically controlled brake system DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.CHECK CAN COMMUNICATION SYSTEM

B

2.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

3.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

3.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

4.CHECK AUXILIARY BATTERY

NG

CONNECT CONNECTOR TO SKID CONTROL ECU CORRECTLY

4.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

5.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C249762C53
0.208,0.802 0.625,1.073 0.417,0.271 1.344,1.865 0.688,2.896 false 0.198,0.188 0.823,0.583 0.625,0.396 10 false *a 0.302,0.854 0.99,1.167 0.688,0.313 10 false A28 0.594,2.948 1.198,3.427 0.604,0.479 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C249762C54
0.208,0.802 0.625,1.073 0.417,0.271 2.063,1.792 1.521,0.979 false 2.156,1.792 1.729,0.719 false 2.646,2.042 3.031,2.813 false 2.188,0.979 2.26,1.792 false 2.5,0.708 2.365,1.792 false 2.469,1.792 2.75,0.969 false 0.198,0.188 0.635,0.531 0.438,0.344 10 false *a 0.302,0.854 1.021,1.198 0.719,0.344 10 false A28 1.25,0.792 1.75,1.042 0.5,0.25 10 false GND6 1.531,0.531 1.948,0.781 0.417,0.25 10 false GND5 1.979,0.771 2.479,1.01 0.5,0.24 10 false GND4 2.354,0.521 2.771,0.76 0.417,0.24 10 false GND3 2.906,2.844 3.26,3 0.354,0.156 10 false GND 2.615,0.771 3.198,1.01 0.583,0.24 10 false GND2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-28 (GND) - Body ground Always Below 1 Ω
A28-27 (GND2) - Body ground Always Below 1 Ω
A28-26 (GND3) - Body ground Always Below 1 Ω
A28-25 (GND4) - Body ground Always Below 1 Ω
A28-24 (GND5) - Body ground Always Below 1 Ω
A28-23 (GND6) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

7.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH ASSEMBLY)
a.

Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch assembly ON or OFF ON: Parking brake applied
OFF: Parking brake released
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Parking Brake SW
50003 105 38

e.

Using the intelligent tester, check if the switch condition on the intelligent tester changes according to parking brake operation.

OK:

The intelligent tester displays ON or OFF according to parking brake operation.



Result:
Proceed to
OK
NG



OK

8.INSPECT COMBINATION METER ASSEMBLY

NG

9.INSPECT PARKING BRAKE SWITCH ASSEMBLY
8.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the power switch off.


b.

Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST


c.

Check the combination meter assembly.

OK:

The brake warning light / red (malfunction) turns on or off in accordance with intelligent tester operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

9.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.
C211519C06
1.656,1.927 0.844,2.802 false 0.375,0.292 0.542,0.458 0.167,0.167 10 *a 0.75,2.802 0.875,2.969 0.125,0.167 10 +
*a Component without harness connected
(Parking Brake Switch Assembly)


Turn the power switch off.


b.

Disconnect the A42 parking brake switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (+) - Body ground Parking brake switch assembly ON
(Switch pin free)
Below 1 Ω
1 (+) - Body ground Parking brake switch assembly OFF
(Switch pin pushed in)
10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - PARKING BRAKE SWITCH ASSEMBLY)

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - PARKING BRAKE SWITCH ASSEMBLY)
a.

Disconnect the 3D main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-20 (PKB) - A42-1 (+) Always Below 1 Ω
3D-20 (PKB) - Body ground Always 10 kΩ or higher


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR