Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on the "Communication Bus Check" screen of the intelligent tester

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Power source circuit of ECM

·

ECM main line or connector

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C252898E08
2.198,4.552 2.135,5.25 2.135,5.25 2,5.25 false 3.115,4.552 2.99,5.552 2.99,5.552 2.802,5.552 false 5.073,5.01 6.677,5.427 1.604,0.417 10 false Trouble Area 1.854,2.333 2.354,2.604 0.5,0.271 10 false DLC3 1.281,0.594 3.781,0.927 2.5,0.333 10 false : CAN Main Bus Line (CANH) 1.281,0.938 3.781,1.271 2.5,0.333 10 false : CAN Main Bus Line (CANL) 1.281,1.271 3.01,1.604 1.729,0.333 10 false : CAN Branch Line (CANH) 1.292,1.615 3.021,1.948 1.729,0.333 10 false : CAN Branch Line (CANL) 4.771,4.563 5.156,4.719 0.385,0.156 10 false ECM 0.125,5.146 2.083,5.333 1.958,0.188 10 false CAN Junction RH1 Connector 0.292,4.563 1.469,4.979 1.177,0.417 10 false Combination Meter Assembly 0.906,5.458 2.896,5.625 1.99,0.167 10 false CAN Junction LH1 Connector 5.25,3.115 5.583,3.281 0.333,0.167 10 false +B2 5.313,3.51 5.552,3.688 0.24,0.177 10 false +B 5.125,3.958 5.531,4.156 0.406,0.198 10 false IGSW 5.344,4.344 5.542,4.521 0.198,0.177 10 false E1 4.313,3.74 4.698,3.917 0.385,0.177 10 false CANL 4.313,3.104 4.719,3.281 0.406,0.177 10 false CANH 0.49,3.979 0.885,4.156 0.396,0.177 10 false 120 Ω 4.385,4 4.781,4.177 0.396,0.177 10 false 120 Ω 5.615,3.948 5.917,4.146 0.302,0.198 10 false A25 5.594,4.365 5.948,4.542 0.354,0.177 10 false E28 5.688,2.938 5.833,3.094 0.146,0.156 10 false 3 5.688,3.333 5.833,3.51 0.146,0.177 10 false 2 5.646,3.781 6.313,3.969 0.667,0.188 10 false 37 5.646,4.188 6.313,4.333 0.667,0.146 10 false 16 4.021,3.021 4.198,3.167 0.177,0.146 10 false 13 4.021,3.656 4.208,3.813 0.188,0.156 10 false 26 6.365,3.927 6.948,4.417 0.583,0.49 10 false ECU-IG2 NO. 3 fuse 5.625,2.625 6.906,2.875 1.281,0.25 10 false to EFI MAIN Relay 3.979,3.198 4.292,3.344 0.313,0.146 10 false A25 3.979,3.823 4.292,3.969 0.313,0.146 10 false A25 0.135,0.073 1.458,0.333 1.323,0.26 12 false V Bus: 5.594,3.521 5.896,3.719 0.302,0.198 10 false A25 5.594,3.115 5.896,3.313 0.302,0.198 10 false A25 0.052,4.563 0.365,4.719 0.313,0.156 10 false I18

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, turn the cruise control system on using the cruise control main switch (ON/OFF switch), wait at least 60 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the ECM connector.


c.
C239823C15
1.677,0.583 2.094,0.865 0.417,0.281 2.583,1.625 2.948,1.625 2.948,1.625 2.948,2.406 false 2.573,1.542 2.573,0.948 2.573,0.948 2.813,0.948 false 0.115,0.125 0.365,0.375 0.25,0.25 10 false *a 2.885,0.844 3.365,1.083 0.479,0.24 10 false CANH 2.76,2.438 3.25,2.688 0.49,0.25 10 false CANL 1.75,0.635 2.031,0.813 0.281,0.177 10 false A25
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-13 (CANH) - A25-26 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

2.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM MAIN LINE)

2.CHECK ECM POWER SOURCE CIRCUIT
a.

Check the ECM power source circuit.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>ECM Power Source Circuit

Result:
Result
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)