Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0129  Lost Communication with Brake System Control Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0129 Lost Communication with Brake System Control Module No communication from the brake booster with master cylinder assembly (skid control ECU) continues.
·

Brake booster with master cylinder assembly (skid control ECU) branch line or connector

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU) ground circuit

·

Brake booster with master cylinder assembly (skid control ECU)


As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs.

HINT:

This diagnosis procedure is for when DTC U0129 is output only by the power management control ECU (intelligent tester display: Hybrid Control).


WIRING DIAGRAM

C244195E17
1.135,5.01 3.052,5.219 1.917,0.208 10 false : CAN Main Bus Line (CANH) 2.677,0.771 4.688,0.979 2.01,0.208 10 false CAN No. 1 Junction Connector 0.479,2.844 1.719,3.208 1.24,0.365 10 false Power Management Control ECU 0.667,2.271 1.115,2.479 0.448,0.208 10 false 120 Ω 6.188,2.271 6.635,2.479 0.448,0.208 10 false 120 Ω 6.188,2.833 6.635,3.042 0.448,0.208 10 false ECM 5.292,3.875 6.156,4.083 0.865,0.208 10 false Trouble Area 3.302,3.073 3.51,3.281 0.208,0.208 10 false 35 3.208,3.271 3.625,3.438 0.417,0.167 10 false CA2H 2.677,4.083 4.854,4.469 2.177,0.385 10 false Brake Booster with Master Cylinder Assembly (Skid Control ECU) 1.927,3.729 2.979,3.896 1.052,0.167 10 false ECU-IG1 NO. 1 3.021,3.573 3.438,3.74 0.417,0.167 10 false IG1 2.375,4.083 2.698,4.271 0.323,0.188 10 false A28 5.896,2.833 6.177,3 0.281,0.167 10 false A25 2.354,0.771 2.635,0.938 0.281,0.167 10 false A72 0.281,2.844 0.563,3.01 0.281,0.167 10 false I4 3.792,3.271 4.208,3.438 0.417,0.167 10 false CA2L 4.073,3.573 4.427,3.74 0.354,0.167 10 false GND 3.927,3.073 4.135,3.281 0.208,0.208 10 false 34 4.438,3.469 4.646,3.677 0.208,0.208 10 false 28 2.792,3.469 3,3.677 0.208,0.208 10 false 16 1.135,5.417 3.052,5.625 1.917,0.208 10 false : CAN Main Bus Line (CANL) 4.271,5.01 6.188,5.219 1.917,0.208 10 false : CAN Branch Line (CANH) 4.271,5.417 6.188,5.625 1.917,0.208 10 false : CAN Branch Line (CANL) 0.052,0.073 1.365,0.49 1.313,0.417 12 false Sub Bus 15:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 60 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
OK:

DTC C1241 is not output.



Result:
Result
OK
NG



OK

2.RECONFIRM DTC OUTPUT

NG

2.RECONFIRM DTC OUTPUT
a.

Check if Hybrid Control of the power management control ECU outputs only DTC U0129.

Powertrain > Hybrid Control > Trouble Codes
50001 236
HINT:

If the power management control ECU outputs DTC U0100 and DTC U0129, check the branch circuit of sub bus 15.



Result:
Result Proceed to
The power management control ECU outputs only DTC U0129.
(Intelligent tester display: Hybrid Control)
A
The power management control ECU outputs DTC U0100 and U0129.
(Intelligent tester display: Hybrid Control)
B



A

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

3.CHECK FOR OPEN IN CAN BUS LINES (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.


c.
C209401C78
1.531,0.771 1.948,1.042 0.417,0.271 1.115,2.698 1.656,2.146 false 1.99,2.688 1.76,2.146 false 0.198,0.156 0.385,0.313 0.188,0.156 10 false *a 1.604,0.813 1.896,0.969 0.292,0.156 10 false A28 0.771,2.708 1.135,2.885 0.365,0.177 10 false CA2L 1.896,2.698 2.281,2.875 0.385,0.177 10 false CA2H
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-35 (CA2H) - A28-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)