Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0100  Lost Communication with ECM / PCM "A"  U0129  Lost Communication with Brake System Control Module  U0293  Lost Communication with HV ECU  


DESCRIPTION

·

The power management control ECU communicates with the ECM and brake booster with master cylinder assembly (skid control ECU). When the power management control ECU does not receive data from the ECM or brake booster with master cylinder assembly (skid control ECU), the power management control ECU stores DTC U0100 or U0129.

·

The ECM communicates with the power management control ECU. When the ECM does not receive data from the power management control ECU, the ECM stores DTC U0293.

·

The brake booster with master cylinder assembly (skid control ECU) communicates with the power management control ECU. When the brake booster with master cylinder assembly (skid control ECU) does not receive data from the power management control ECU, the brake booster with master cylinder assembly (skid control ECU) stores DTC U0293.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0100 Lost Communication with ECM / PCM "A" The power management control ECU does not receive data from the ECM.
·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of power management control ECU

·

Power management control ECU

·

Power source circuit of ECM

·

ECM

·

Open or short in CAN No. 1 junction connector


As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs.
U0129 Lost Communication with Brake System Control Module The power management control ECU does not receive data from the brake booster with master cylinder assembly (skid control ECU).
·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of power management control ECU

·

Power management control ECU

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU)

·

Open or short in CAN No. 1 junction connector


As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs.
U0293 Lost Communication with HV ECU
·

The ECM does not receive data from the power management control ECU.

·

The brake booster with master cylinder assembly (skid control ECU) does not receive data from the power management control ECU.


·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of ECM

·

ECM

·

Power source circuit of power management control ECU

·

Power management control ECU

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU)

·

Open or short in CAN No. 1 junction connector


As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs.

HINT:

This diagnosis procedure is for when DTC U0100, U0129 and U0293 are output at the same time.


WIRING DIAGRAM

C244197E08
0.809,0.936 0.958,1.092 0.15,0.156 10 I4 0.99,0.936 2.3,1.271 1.31,0.335 10 Power Management Control ECU 1.369,3.871 2.679,4.206 1.31,0.335 10 CAN No. 1 Junction Connector 2.064,6.771 2.451,7.106 0.387,0.335 10 ECM 1.739,6.771 2.025,7.106 0.286,0.335 10 A25 5.262,4.535 6.989,5.046 1.727,0.511 10 Brake Booster with Master Cylinder Assembly (Skid Control ECU) 4.924,4.535 5.212,4.897 0.288,0.362 10 A28 3.316,0.77 3.83,0.961 0.514,0.191 10 120 Ω 3.344,7.039 3.859,7.23 0.514,0.191 10 120 Ω 2.675,1.354 3.097,1.534 0.423,0.18 10 CA3N 3.984,1.354 4.406,1.534 0.423,0.18 10 CA3P 5.87,3.47 6.293,3.65 0.423,0.18 10 CA2H 5.87,4.11 6.293,4.29 0.423,0.18 10 CA2L 2.682,6.427 3.105,6.606 0.423,0.18 10 CANN 3.968,6.427 4.391,6.606 0.423,0.18 10 CANP 2.917,1.641 3.144,1.875 0.226,0.234 10 30 1.059,3.871 1.328,4.105 0.269,0.234 10 A72 3.971,1.641 4.197,1.875 0.226,0.234 10 31 2.917,6.161 3.144,6.395 0.226,0.234 10 25 3.971,6.161 4.197,6.395 0.226,0.234 10 12 2.959,2.982 3.186,3.216 0.226,0.234 10 9 4.013,2.982 4.239,3.216 0.226,0.234 10 3 2.889,2.255 3.116,2.489 0.226,0.234 10 W 4.041,2.255 4.267,2.489 0.226,0.234 10 B 5.194,3.394 5.42,3.628 0.226,0.234 10 B 5.171,4.181 5.397,4.415 0.226,0.234 10 W 2.889,5.671 3.116,5.905 0.226,0.234 10 W 4.041,5.671 4.267,5.905 0.226,0.234 10 B 4.282,3.466 4.509,3.7 0.226,0.234 10 1 4.282,4.11 4.509,4.344 0.226,0.234 10 7 5.655,3.466 5.882,3.7 0.226,0.234 10 35 5.655,4.11 5.882,4.344 0.226,0.234 10 34 2.959,4.968 3.186,5.202 0.226,0.234 10 8 4.013,4.968 4.239,5.202 0.226,0.234 10 2 0.98,7.994 2.883,8.174 1.903,0.18 10 : CAN Main Bus Line (CANH) 0.98,8.401 2.883,8.581 1.903,0.18 10 : CAN Main Bus Line (CANL) 3.935,7.998 5.838,8.178 1.903,0.18 10 : CAN Branch Line (CANH) 3.935,8.405 5.838,8.585 1.903,0.18 10 : CAN Branch Line (CANL) 0.091,0.104 1.775,0.607 1.684,0.503 12 Sub Bus 15:

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 5 seconds.

·

After the repair, perform Communication Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Check if Hybrid Control of the power management control ECU outputs only DTC U0129.

Powertrain > Hybrid Control > Trouble Codes
50001 236
HINT:

If the power management control ECU outputs only DTC U0129, troubleshoot DTC U0129 and check the branch circuit of sub bus 15.



Result:
Result Proceed to
The power management control ECU outputs DTC U0129 and other DTCs.
(Intelligent tester display: Hybrid Control)
A
The power management control ECU outputs only DTC U0129.
(Intelligent tester display: Hybrid Control)
B



A

2.CHECK SUB BUS 15

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK SUB BUS 15
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A261175C12
2.458,0.417 2.917,0.667 0.458,0.25 1.865,1 2.427,1.698 false 2.75,0.979 2.635,1.698 false 2.417,1.906 2.146,2.375 false 2.469,1.906 2.802,2.375 false 0.083,0.083 0.396,0.344 0.313,0.26 10 false *a 2.667,2.396 3.146,2.604 0.479,0.208 10 false CA3N 2.635,0.813 3.042,1.042 0.406,0.229 10 false E12 1.948,2.396 2.427,2.604 0.479,0.208 10 false CA3P 1.677,0.813 2.083,1.042 0.406,0.229 10 false AM21 2.646,0.448 3.052,0.677 0.406,0.229 10 false I4
*a Component with harness connected
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I4-31 (CA3P) - I4-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in a main bus line
I4-31 (CA3P) - I4-4 (E12) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I4-30 (CA3N) - I4-4 (E12) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I4-31 (CA3P) - I4-7 (AM21) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I4-30 (CA3N) - I4-7 (AM21) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

When the values are as specified, clear and recheck for DTCs. When no DTCs are output, check for malfunctions such as damage or improper connection of the relevant connectors.

·

If DTCs are output although the bus circuit is normal and DTCs were cleared, replace the power management control ECU.




Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus line) B
NG (Short circuit between bus lines) C
·

NG (Ground short)

·

NG (+B short)


D



A

B

3.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (POWER MANAGEMENT CONTROL ECU)

C

6.CHECK FOR SHORT IN SUB BUS 15 LINES (POWER MANAGEMENT CONTROL ECU)

D

10.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 1 J/C)
3.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the power management control ECU connector.


b.
A204446C39
2.417,3 2.917,3.25 0.5,0.25 1.75,2.917 2.427,2.573 false 1.75,3.167 2.469,2.573 false 2.604,3.031 3.042,3.333 0.438,0.302 10 false I4 1.333,2.813 1.823,3.083 0.49,0.271 10 false CA3P 1.333,3.073 1.833,3.333 0.5,0.26 10 false CA3N 0.156,0.052 0.479,0.333 0.323,0.281 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I4-31 (CA3P) - I4-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

4.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN NO. 1 J/C)
4.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN NO. 1 J/C)
a.

Reconnect the power management control ECU connector.


b.

Disconnect the CAN No. 1 junction connector.


c.
C234634C43
0.281,1.604 0.833,1.875 0.552,0.271 1.604,1.729 1.604,0.771 1.604,0.771 1.948,0.771 false 1.604,2.104 1.604,2.75 1.604,2.75 1.969,2.75 false 0.927,0.948 1.438,0.948 1.438,0.948 1.438,1.729 false 0.917,2.594 1.427,2.594 1.427,2.594 1.427,2.104 false 0.115,0.104 0.375,0.323 0.26,0.219 10 false *a 0.406,1.646 0.698,1.854 0.292,0.208 10 false A72 2,0.688 2.667,1.01 0.667,0.323 10 false CANH*c 2.031,2.667 2.698,2.99 0.667,0.323 10 false CANL*c 0.354,0.885 1.021,1.208 0.667,0.323 10 false CANH*b 0.385,2.51 1.052,2.833 0.667,0.323 10 false CANL*b
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to ECM
*c to Power Management Control ECU


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A72-2 (CANH) - A72-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
A72-3 (CANH) - A72-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU



Result:
Result Proceed to
OK A
NG (Open circuit in power management control ECU CAN main bus line) B
NG (Open circuit in ECM CAN main bus line) C



A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - CAN NO. 1 J/C)

C

5.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (ECM - CAN NO. 1 J/C)
5.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (ECM - CAN NO. 1 J/C)
a.

Reconnect the CAN No. 1 junction connector.


b.

Disconnect the ECM connector.


c.
C239823C16
1.677,0.583 2.167,0.833 0.49,0.25 2.5,1.625 2.865,1.625 2.865,1.625 2.865,2.333 false 2.49,1.542 2.49,0.875 2.49,0.875 2.771,0.875 false 0.083,0.083 0.479,0.406 0.396,0.323 10 false *a 2.865,0.792 3.333,1.083 0.469,0.292 10 false CANP 2.729,2.365 3.25,2.667 0.521,0.302 10 false CANN 1.781,0.615 2.323,0.875 0.542,0.26 10 false A25
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-12 (CANP) - A25-25 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - CAN NO. 1 J/C)

6.CHECK FOR SHORT IN SUB BUS 15 LINES (POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the power management control ECU connector.


b.
A204446C39
2.417,3 2.917,3.25 0.5,0.25 1.75,2.917 2.427,2.573 false 1.75,3.167 2.469,2.573 false 2.604,3.031 3.042,3.333 0.438,0.302 10 false I4 1.333,2.813 1.823,3.083 0.49,0.271 10 false CA3P 1.333,3.073 1.833,3.333 0.5,0.26 10 false CA3N 0.156,0.052 0.479,0.333 0.323,0.281 10 false *a
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I4-31 (CA3P) - I4-30 (CA3N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

7.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 1 J/C)
7.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 1 J/C)
a.

Reconnect the power management control ECU connector.


b.

Disconnect the CAN No. 1 junction connector.


c.
C234634C44
0.281,1.573 0.833,1.844 0.552,0.271 1.604,1.729 1.604,0.76 1.604,0.76 1.948,0.76 false 1.604,2.104 1.604,2.76 1.604,2.76 1.969,2.76 false 1,0.563 1.427,0.563 1.427,0.563 1.427,1.719 false 1.052,2.969 1.427,2.969 1.427,2.969 1.427,2.104 false 0.875,0.927 1.25,0.927 1.25,0.927 1.25,1.708 false 0.854,2.583 1.24,2.583 1.24,2.583 1.24,2.104 false 0.115,0.042 0.375,0.26 0.26,0.219 10 false *a 0.417,1.625 0.708,1.833 0.292,0.208 10 false A72 2.01,0.677 2.677,1 0.667,0.323 10 false CANH*c 2,2.677 2.667,3 0.667,0.323 10 false CANL*c 0.396,0.49 1.063,0.677 0.667,0.188 10 false CANH*b 0.5,2.896 1.167,3.073 0.667,0.177 10 false CANL*b 0.281,0.865 0.948,1.052 0.667,0.188 10 false CANH*d 0.323,2.5 0.99,2.677 0.667,0.177 10 false CANL*d
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to ECM
*c to Power Management Control ECU
*d to Brake Booster with Master Cylinder Assembly (Skid Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A72-1 (CANH) - A72-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (skid control ECU)
A72-2 (CANH) - A72-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
A72-3 (CANH) - A72-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU



Result:
Result Proceed to
OK A
NG (Short circuit between bus lines in power management control ECU CAN main bus line) B
NG (Short circuit between bus lines in ECM CAN main bus line) C
NG (Short circuit between bus lines in brake booster with master cylinder assembly (skid control ECU) CAN branch line) D



A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - CAN NO. 1 J/C)

C

8.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN NO. 1 J/C)

D

9.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER - CAN NO. 1 J/C)
8.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN NO. 1 J/C)
a.

Reconnect the CAN No. 1 junction connector.


b.

Disconnect the ECM connector.


c.
C239823C16
1.677,0.583 2.167,0.833 0.49,0.25 2.5,1.625 2.865,1.625 2.865,1.625 2.865,2.333 false 2.49,1.542 2.49,0.875 2.49,0.875 2.771,0.875 false 0.083,0.083 0.479,0.406 0.396,0.323 10 false *a 2.865,0.792 3.333,1.083 0.469,0.292 10 false CANP 2.729,2.365 3.25,2.667 0.521,0.302 10 false CANN 1.781,0.615 2.323,0.875 0.542,0.26 10 false A25
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-12 (CANP) - A25-25 (CANN) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - CAN NO. 1 J/C)

9.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER - CAN NO. 1 J/C)
a.

Reconnect the CAN No. 1 junction connector.


b.

Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.


c.
C209401C78
1.531,0.771 1.948,1.042 0.417,0.271 1.115,2.698 1.656,2.146 false 1.99,2.688 1.76,2.146 false 0.198,0.156 0.385,0.313 0.188,0.156 10 false *a 1.604,0.813 1.896,0.969 0.292,0.156 10 false A28 0.771,2.708 1.135,2.885 0.365,0.177 10 false CA2L 1.896,2.698 2.281,2.875 0.385,0.177 10 false CA2H
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-35 (CA2H) - A28-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)

10.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 1 J/C)
a.

Disconnect the CAN No. 1 junction connector.


b.
C261310C01
0.333,1.458 0.74,1.677 0.406,0.219 0.292,3.917 0.698,4.135 0.406,0.219 1.25,1.458 1.25,0.646 1.25,0.646 0.938,0.646 false 1.427,1.458 1.427,0.375 1.427,0.375 1.115,0.375 false 1.594,1.458 1.594,0.375 1.594,0.375 1.938,0.375 false 1.25,1.823 1.25,2.396 1.25,2.396 0.958,2.396 false 1.417,1.823 1.417,2.677 1.417,2.677 1.104,2.677 false 1.594,1.823 1.594,2.677 1.594,2.677 1.906,2.677 false 1.625,3.542 1.5,3.083 1.5,3.083 1.323,3.083 false 2.406,4.021 2.813,4.021 false 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 0.563,0.292 1.219,0.448 0.656,0.156 10 false CANH*b 2,0.302 2.604,0.469 0.604,0.167 10 false CANH*c 0.385,0.552 1,0.719 0.615,0.167 10 false CANH*d 0.396,2.323 1.01,2.49 0.615,0.167 10 false CANL*d 0.542,2.594 1.198,2.75 0.656,0.156 10 false CANL*b 1.969,2.594 2.573,2.76 0.604,0.167 10 false CANL*c 0.406,1.479 0.719,1.635 0.313,0.156 10 false A72 0.406,3.938 0.719,4.094 0.313,0.156 10 false I39 1.052,3 1.365,3.177 0.313,0.177 10 false CG 2.875,3.948 3.271,4.135 0.396,0.188 10 false BAT
*a Front view of wire harness connector
(to CAN No. 1 Junction Connector)
*b to ECM
*c to Power Management Control ECU
*d to Brake Booster with Master Cylinder Assembly (Skid Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A72-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Brake booster with master cylinder assembly (skid control ECU)
A72-7 (CANL) - I39-4 (CG)
A72-2 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher ECM
A72-8 (CANL) - I39-4 (CG)
A72-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Power management control ECU
A72-9 (CANL) - I39-4 (CG)
A72-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Brake booster with master cylinder assembly (skid control ECU)
A72-7 (CANL) - I39-16 (BAT)
A72-2 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher ECM
A72-8 (CANL) - I39-16 (BAT)
A72-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Power management control ECU
A72-9 (CANL) - I39-16 (BAT)


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 15 inspection.




Result:
Result Proceed to
OK A
·

NG (Ground short in power management control ECU CAN main bus line)

·

NG (+B short in power management control ECU CAN main bus line)


B
·

NG (Ground short in ECM CAN main bus line)

·

NG (+B short in ECM CAN main bus line)


C
·

NG (Ground short in brake booster with master cylinder assembly (skid control ECU) CAN branch line)

·

NG (+B short in brake booster with master cylinder assembly (skid control ECU) CAN branch line)


D



A

REPLACE CAN NO. 1 JUNCTION CONNECTOR

B

11.CHECK FOR SHORT IN SUB BUS 15 LINES (POWER MANAGEMENT CONTROL ECU - CAN NO. 1 J/C)

C

12.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN NO. 1 J/C)

D

13.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER - CAN NO. 1 J/C)
11.CHECK FOR SHORT IN SUB BUS 15 LINES (POWER MANAGEMENT CONTROL ECU - CAN NO. 1 J/C)
a.

Disconnect the power management control ECU connector.


b.
A204446C40
2.417,3 2.917,3.25 0.5,0.25 2.427,2.354 2.083,2.083 false 2.625,2.365 2.99,2.094 false 1.75,2.917 2.427,2.573 false 1.75,3.167 2.469,2.573 false 2.594,3.031 3.031,3.333 0.438,0.302 10 false I4 1.333,2.813 1.823,3.083 0.49,0.271 10 false CA3P 1.333,3.073 1.833,3.333 0.5,0.26 10 false CA3N 0.156,0.052 0.479,0.333 0.323,0.281 10 false *a 1.667,2 2.167,2.25 0.5,0.25 10 false AM21 3.052,2 3.396,2.25 0.344,0.25 10 false E12
*a Rear view of wire harness connector
(to Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I4-31 (CA3P) - I4-4 (E12) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
I4-30 (CA3N) - I4-4 (E12)
I4-31 (CA3P) - I4-7 (AM21) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
I4-30 (CA3N) - I4-7 (AM21)


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 15 inspection.




Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - CAN NO. 1 J/C)

12.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN NO. 1 J/C)
a.

Disconnect the ECM connector.


b.
C261311C02
1.5,0.083 2,0.333 0.5,0.25 0.667,2.667 1.167,2.917 0.5,0.25 1.271,1.104 1.271,0.417 1.271,0.417 1.021,0.417 false 2.375,1.094 2.375,0.417 2.375,0.417 2.625,0.417 false 3,1.427 3,1.177 3,1.177 2.385,1.177 false 1.531,3.51 1.531,2.844 1.531,2.844 1.781,2.844 false 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.615,0.125 2.229,0.323 0.615,0.198 10 false A25 0.583,0.333 1.198,0.531 0.615,0.198 10 false BATT 2.698,0.323 3.313,0.521 0.615,0.198 10 false CANP 2.813,1.448 3.333,1.729 0.521,0.281 10 false CANN 0.792,2.708 1.406,2.906 0.615,0.198 10 false E28 1.854,2.75 2.167,2.948 0.313,0.198 10 false E1
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-12 (CANP) - E28-16 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A25-25 (CANN) - E28-16 (E1)
A25-12 (CANP) - A25-1 (BATT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A25-25 (CANN) - A25-1 (BATT)


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 15 inspection.




Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - CAN NO. 1 J/C)

13.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER - CAN NO. 1 J/C)
a.

Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.


b.
C259445C01
1.521,0.813 1.938,1.021 0.417,0.208 2.667,1.729 2.823,0.969 false 2.833,2.802 2.656,2.042 false 2.115,2.875 1.76,2.146 false 1.354,2.844 1.646,2.146 false 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 2.781,0.771 3.094,0.969 0.313,0.198 10 false BS 2.792,2.844 3.104,3.042 0.313,0.198 10 false GND 2.063,2.896 2.583,3.115 0.521,0.219 10 false CA2H 1.083,2.896 1.604,3.115 0.521,0.219 10 false CA2L 1.594,0.833 2.115,1.052 0.521,0.219 10 false A28
*a Front view of wire harness connector
(to Brake Booster with Master Cylinder Assembly (Skid Control ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-35 (CA2H) - A28-28 (GND) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A28-34 (CA2L) - A28-28 (GND)
A28-35 (CA2H) - A28-15 (BS) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A28-34 (CA2L) - A28-15 (BS)


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 15 inspection.

·

Find the necessary inspection from the Purpose column that matches the result in the Result column from the Check Sub Bus 15 inspection.




Result:
Result
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)