Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075054 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the power management control ECU to the ACC relay.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2274 ACC Monitor Malfunction Malfunction in the ACC relay circuit in the power management control ECU or in the external circuit (1-trip detection logic*).
·

AM2 fuse

·

ACC relay (Instrument panel junction block assembly)

·

Power management control ECU

·

Wire harness or connector


DTC Output Confirmation Operation

Wait 10 seconds after turning the power switch on (ACC) or on (IG), and then wait another 10 seconds after turning the power switch off.


HINT:

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.



*: Only detected while a malfunction is present.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the power switch is off.

·

If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the power switch is on (ACC).


HINT:

The power switch can be turned on (IG) and the hybrid control system can be started.


-

WIRING DIAGRAM

B296600E01
3.292,1.021 3.385,1.177 0.094,0.156 10 false 1 2.76,1.219 3.188,1.375 0.427,0.156 10 false ACCD 4.833,1.521 5.563,1.677 0.729,0.156 10 false ACC NO. 1 4.833,2.74 5.563,2.896 0.729,0.156 10 false ACC NO. 2 2.063,2.99 3.333,3.354 1.271,0.365 10 false Power Management Control ECU 3.823,2.958 6.677,3.417 2.854,0.458 10 false Instrument Panel Junction Block Assembly 3.292,1.198 3.635,1.365 0.344,0.167 10 false I4 3.771,1.198 4.135,1.49 0.365,0.292 10 false 3B 3.802,1.031 4.042,1.198 0.24,0.167 10 false 23 3.823,0.625 3.958,0.792 0.135,0.167 10 false 1 5.698,0.948 6.51,1.156 0.813,0.208 10 false ECU-ACC 5.833,2.167 6.594,2.542 0.76,0.375 10 false P/OUTLET RR 6.406,0.625 6.646,0.792 0.24,0.167 10 false 37 6.385,0.792 6.604,0.958 0.219,0.167 10 false 3B 6.396,1.792 6.635,1.958 0.24,0.167 10 false 10 6.438,2.313 6.677,2.479 0.24,0.167 10 false 7 6.385,1.969 6.604,2.135 0.219,0.167 10 false 3B 6.396,2.479 6.615,2.646 0.219,0.167 10 false 3B 3.781,0.781 4.021,0.948 0.24,0.167 10 false 3F 2.281,1.365 2.719,1.51 0.438,0.146 10 false E01 2,1.167 2.115,1.313 0.115,0.146 10 false 5 1.99,1.344 2.26,1.531 0.271,0.188 10 false I3 2.281,1.76 2.719,1.906 0.438,0.146 10 false E02 2.01,1.552 2.125,1.698 0.115,0.146 10 false 5 1.99,1.74 2.26,1.927 0.271,0.188 10 false I4 2.281,2.229 2.719,2.375 0.438,0.146 10 false E1 2,2.031 2.115,2.177 0.115,0.146 10 false 6 1.979,2.219 2.25,2.406 0.271,0.188 10 false I3 2.281,2.615 2.719,2.76 0.438,0.146 10 false E12 2,2.427 2.115,2.573 0.115,0.146 10 false 4 1.99,2.615 2.26,2.802 0.271,0.188 10 false I4 0.031,0.563 0.896,0.875 0.865,0.313 10 false from Auxiliary Battery 1.198,0.698 1.531,0.885 0.333,0.188 10 false AM2 2.281,0.563 2.719,0.708 0.438,0.146 10 false AM21 1.99,0.375 2.104,0.521 0.115,0.146 10 false 7 1.979,0.563 2.188,0.75 0.208,0.188 10 false I4 2.281,0.969 2.719,1.115 0.438,0.146 10 false AM22 1.99,0.76 2.104,0.906 0.115,0.146 10 false 1 1.979,0.948 2.25,1.135 0.271,0.188 10 false I3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2274
Power Source Control
·

ACC Relay Monitor


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

2.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

2.CHECK HARNESS AND CONNECTOR (GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the I4 connector from the power management control ECU.


b.

Disconnect the 3B connector from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
I4-1 (ACCD) - 3B-23 Always Below 1 Ω
3B-7 - Body ground Always Below 1 Ω
I4-1 (ACCD) or 3B-23 - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL

B298807C01
1.992,0.051 2.309,0.311 0.317,0.26 2.062,0.116 2.505,0.385 0.443,0.27 10 3B 4.958,0.131 5.275,0.391 0.317,0.26 5.028,0.196 5.471,0.465 0.443,0.27 10 3F 0.082,0.0 0.368,0.208 0.286,0.208 10 *a
*a Component without harness connected(Instrument Panel Junction Block Assembly) - -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
·

3F-1 - 3B-37


·

3F-1 - 3B-10


Auxiliary battery voltage not applied to terminals 3B-23 and 3B-7 10 kΩ or higher
Auxiliary battery voltage applied to terminals 3B-23 and 3B-7 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT POWER MANAGEMENT CONTROL ECU

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.INSPECT POWER MANAGEMENT CONTROL ECU
a.
B229525C09
2.479,0.417 2.896,0.656 0.417,0.24 2.719,1.885 2.833,1.115 false 0.052,0.052 0.323,0.26 0.271,0.208 10 false *a 2.615,0.458 2.885,0.635 0.271,0.177 10 false I4 2.531,1.896 3.01,2.104 0.479,0.208 10 false ACCD
*a Component with harness connected(Power Management Control ECU)


Reconnect the I4 power management control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I4-1 (ACCD) - Body ground Power switch off → Power switch on (ACC) 1 V or less → 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG