Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075054 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the power management control ECU receives a signal and changes the power source mode.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


WIRING DIAGRAM

B296599E02
4.865,6.938 5.115,7.094 0.25,0.156 10 false IG2 4.406,7.313 6.188,7.51 1.781,0.198 10 false No. 1 Integration Relay 2.625,1.063 3.125,1.333 0.5,0.271 10 false IG1D 2.625,6.635 2.969,6.781 0.344,0.146 10 false IG2D 4.656,4.927 5.354,5.073 0.698,0.146 10 false IG1 NO. 4 3.625,5.385 6.406,5.688 2.781,0.302 10 false Instrument Panel Junction Block Assembly 1.958,7.188 3.229,7.552 1.271,0.365 10 false Power Management Control ECU 4.656,3.74 5.354,3.885 0.698,0.146 10 false IG1 NO. 3 4.656,2.563 5.354,2.708 0.698,0.146 10 false IG1 NO. 2 4.656,1.375 5.354,1.521 0.698,0.146 10 false IG1 NO. 1 3.104,6.438 3.219,6.583 0.115,0.146 10 false 2 3.125,0.885 3.385,1.156 0.26,0.271 10 false 2 3.104,1.063 3.438,1.25 0.333,0.188 10 false I4 3.021,6.615 3.354,6.802 0.333,0.188 10 false A39 4.021,6.615 4.323,6.771 0.302,0.156 10 false 1C 5.865,6.615 6.146,6.771 0.281,0.156 10 false 1E 4.073,6.448 4.26,6.604 0.188,0.156 10 false 8 5.896,6.427 6.083,6.583 0.188,0.156 10 false 2 3.594,0.646 3.927,0.896 0.333,0.25 10 false 3F 3.583,1.063 4.031,1.521 0.448,0.458 10 false 3A 3.594,0.896 4,1.323 0.406,0.427 10 false 27 3.625,0.479 3.833,0.635 0.208,0.156 10 false 1 6.198,0.656 6.448,0.844 0.25,0.188 10 false 3D 6.24,0.469 6.448,0.615 0.208,0.146 10 false 1 6.208,1.833 6.458,2.021 0.25,0.188 10 false 3D 6.208,1.656 6.604,1.927 0.396,0.271 10 false 36 6.198,3.01 6.448,3.198 0.25,0.188 10 false 3C 6.208,2.823 6.625,3.313 0.417,0.49 10 false 33 6.198,4.615 6.479,4.802 0.281,0.188 10 false 3B 6.25,4.438 6.458,4.583 0.208,0.146 10 false 7 5.625,0.802 6.156,1 0.531,0.198 10 false WIPER 5.646,2.021 6.219,2.5 0.573,0.479 10 false ECU-IG1 NO. 1 5.646,3.198 6.24,3.698 0.594,0.5 10 false ECU-IG1 NO. 3 0.01,1.583 0.865,2.177 0.854,0.594 10 false from Auxiliary Battery 1.156,1.729 1.771,2.135 0.615,0.406 10 false AM2 2.219,1.594 2.875,1.948 0.656,0.354 10 false AM21 1.948,1.406 2.219,1.615 0.271,0.208 10 false 7 1.927,1.583 2.292,1.896 0.365,0.313 10 false I4 2.219,2 2.854,2.354 0.635,0.354 10 false AM22 1.938,1.792 2.177,2.104 0.24,0.313 10 false 1 1.927,1.979 2.198,2.167 0.271,0.188 10 false I3 2.219,3.99 2.75,4.385 0.531,0.396 10 false E01 1.938,3.792 2.052,3.938 0.115,0.146 10 false 5 1.927,3.979 2.198,4.167 0.271,0.188 10 false I3 2.219,4.375 2.656,4.521 0.438,0.146 10 false E02 1.938,4.188 2.052,4.333 0.115,0.146 10 false 5 1.938,4.375 2.208,4.563 0.271,0.188 10 false I4 2.219,4.844 2.813,5.115 0.594,0.271 10 false E1 1.938,4.656 2.052,4.802 0.115,0.146 10 false 6 1.927,4.844 2.198,5.031 0.271,0.188 10 false I3 2.219,5.24 2.656,5.385 0.438,0.146 10 false E12 1.938,5.063 2.052,5.208 0.115,0.146 10 false 4 1.927,5.24 2.198,5.427 0.271,0.188 10 false I4

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART).

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS).

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IG1 Relay Monitor (Inside)

·

IG2 Relay Monitor (Inside)

·

IG1 Relay Monitor (Outside)

·

IG2 Relay Monitor (Outside)

·

IG1 Circuit

·

IG2 Circuit


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Disconnect the A39 connector from the power management control ECU.


b.

Disconnect the 1C and 1E connectors from the No. 1 integration relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-2 (IG2D) - 1C-8 Always Below 1 Ω
1E-2 - Body ground Always Below 1 Ω
A39-2 (IG2D) or 1C-8 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
a.

Remove the No. 1 integration relay.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>INTEGRATION RELAY>REMOVAL


b.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
Result:
Proceed to
OK
NG


a.

Disconnect the I4 connector from the power management control ECU.


b.

Disconnect the 3A and 3B connectors from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I4-2 (IG1D) - 3A-27 Always Below 1 Ω
3B-7 - Body ground Always Below 1 Ω
I4-2 (IG1D) and 3A-27 - Body ground Always 10 kΩ or higher




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2 AND IG1 NO. 3 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2 AND IG1 NO. 3 RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly .

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

B281391C07
5.007,0.192 5.356,0.441 0.348,0.248 5.098,0.258 5.421,0.475 0.323,0.217 10 3B 5.05,1.421 5.398,1.669 0.348,0.248 5.14,1.486 5.463,1.703 0.323,0.217 10 3D 1.939,0.178 2.287,0.427 0.348,0.248 2.03,0.244 2.352,0.461 0.323,0.217 10 3A 1.925,1.397 2.273,1.645 0.348,0.248 2.016,1.463 2.338,1.68 0.323,0.217 10 3C 3.634,2.581 3.983,2.829 0.348,0.248 3.734,2.635 4.057,2.81 0.323,0.175 10 3F 0.157,0.076 0.403,0.293 0.246,0.217 10 *a
*a Component without harness connected(Instrument Panel Junction Block Assembly) - -


Standard Resistance:
Tester Connection Condition Specified Condition
·

3F-1 - 3D-1(IG1 No. 1 relay)

·

3F-1 - 3D-36(IG1 No. 2 relay)

·

3F-1 - 3D-36(IG1 No. 2 relay)


Auxiliary battery voltage not applied to terminals 3A-27 and 3B-7 10 kΩ or higher
Auxiliary battery voltage applied to terminals 3A-27 and 3B-7 Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK POWER MANAGEMENT CONTROL ECU
a.

Reconnect the A39 and I4 power management control ECU connectors.


b.
B229525C11
1.24,0.417 1.656,0.656 0.417,0.24 2.479,0.417 2.896,0.656 0.417,0.24 1.583,1.125 1.479,1.885 false 2.708,1.906 2.76,1.135 false 0.052,0.052 0.271,0.26 0.219,0.208 10 false *a 1.292,0.458 1.594,0.656 0.302,0.198 10 false A39 2.615,0.458 2.865,0.646 0.25,0.188 10 false I4 1.292,1.896 1.667,2.125 0.375,0.229 10 false IG2D 2.542,1.906 2.969,2.115 0.427,0.208 10 false IG1D
*a Component with harness connected(Power Management Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-2 (IG2D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher
I4-2 (IG1D) - Body ground Power switch on (ACC) → Power switch on (IG) 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG