Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function)
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075054 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (ACC)  


DESCRIPTION

If the power switch is pressed with the electrical key transmitter sub-assembly in the cabin, the power management control ECU receives a signal and changes the power source mode.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


WIRING DIAGRAM

B296600E01
3.292,1.021 3.385,1.177 0.094,0.156 10 false 1 2.76,1.219 3.188,1.375 0.427,0.156 10 false ACCD 4.833,1.521 5.563,1.677 0.729,0.156 10 false ACC NO. 1 4.833,2.74 5.563,2.896 0.729,0.156 10 false ACC NO. 2 2.063,2.99 3.333,3.354 1.271,0.365 10 false Power Management Control ECU 3.823,2.958 6.677,3.417 2.854,0.458 10 false Instrument Panel Junction Block Assembly 3.292,1.198 3.635,1.365 0.344,0.167 10 false I4 3.771,1.198 4.135,1.49 0.365,0.292 10 false 3B 3.802,1.031 4.042,1.198 0.24,0.167 10 false 23 3.823,0.625 3.958,0.792 0.135,0.167 10 false 1 5.698,0.948 6.51,1.156 0.813,0.208 10 false ECU-ACC 5.833,2.167 6.594,2.542 0.76,0.375 10 false P/OUTLET RR 6.406,0.625 6.646,0.792 0.24,0.167 10 false 37 6.385,0.792 6.604,0.958 0.219,0.167 10 false 3B 6.396,1.792 6.635,1.958 0.24,0.167 10 false 10 6.438,2.313 6.677,2.479 0.24,0.167 10 false 7 6.385,1.969 6.604,2.135 0.219,0.167 10 false 3B 6.396,2.479 6.615,2.646 0.219,0.167 10 false 3B 3.781,0.781 4.021,0.948 0.24,0.167 10 false 3F 2.281,1.365 2.719,1.51 0.438,0.146 10 false E01 2,1.167 2.115,1.313 0.115,0.146 10 false 5 1.99,1.344 2.26,1.531 0.271,0.188 10 false I3 2.281,1.76 2.719,1.906 0.438,0.146 10 false E02 2.01,1.552 2.125,1.698 0.115,0.146 10 false 5 1.99,1.74 2.26,1.927 0.271,0.188 10 false I4 2.281,2.229 2.719,2.375 0.438,0.146 10 false E1 2,2.031 2.115,2.177 0.115,0.146 10 false 6 1.979,2.219 2.25,2.406 0.271,0.188 10 false I3 2.281,2.615 2.719,2.76 0.438,0.146 10 false E12 2,2.427 2.115,2.573 0.115,0.146 10 false 4 1.99,2.615 2.26,2.802 0.271,0.188 10 false I4 0.031,0.563 0.896,0.875 0.865,0.313 10 false from Auxiliary Battery 1.198,0.698 1.531,0.885 0.333,0.188 10 false AM2 2.281,0.563 2.719,0.708 0.438,0.146 10 false AM21 1.99,0.375 2.104,0.521 0.115,0.146 10 false 7 1.979,0.563 2.188,0.75 0.208,0.188 10 false I4 2.281,0.969 2.719,1.115 0.438,0.146 10 false AM22 1.99,0.76 2.104,0.906 0.115,0.146 10 false 1 1.979,0.948 2.25,1.135 0.271,0.188 10 false I3

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DIAGNOSTIC TROUBLE CODE CHART).

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS).

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (ACC) but does change to on (IG)
Power Source Control
·

Power Supply Condition

·

ACC Relay Monitor


-


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

OK

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

OK

3.INSPECT POWER MANAGEMENT CONTROL ECU

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

3.INSPECT POWER MANAGEMENT CONTROL ECU

OK

CHECK RELAY CONTACT SIDE CIRCUIT

NG