Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075062 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Security Indicator Light Does not Blink  


DESCRIPTION

·

The certification ECU (smart key ECU assembly) blinks the security indicator light when the immobiliser is set (power switch off, or driver door is opened and closed with power switch on (IG)).

·

The certification ECU (smart key ECU assembly) receive the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is arming preparation state or alarm sounding state. Then, the certification ECU (smart key ECU assembly) blinks the security indicator light.


WIRING DIAGRAM

B278947E27
5.063,1.74 6.719,2.052 1.656,0.313 10 false Main Body ECU (Multiplex Network Body ECU) 2.813,1.781 4.469,2.094 1.656,0.313 10 false Certification ECU (Smart Key ECU Assembly) 2.813,1.635 3.115,1.792 0.302,0.156 10 false I86 0.51,1.594 2.49,1.906 1.979,0.313 10 false Security Indicator Light (Heater Control Switch Board) 0.552,2.458 2.26,2.604 1.708,0.146 10 false : CAN Communication Line 0.51,1.448 0.813,1.604 0.302,0.156 10 false I56 1.031,0.875 1.406,1.031 0.375,0.156 10 false GND 0.844,0.792 0.979,0.948 0.135,0.156 10 false 6 3.042,0.792 3.177,0.948 0.135,0.156 10 false 8 2.042,0.802 2.177,0.958 0.135,0.156 10 false 1 3.198,0.875 3.573,1.031 0.375,0.156 10 false IND 3.688,0.875 4.021,1.031 0.333,0.156 10 false CAN 5.479,0.875 5.813,1.031 0.333,0.156 10 false CAN 1.802,0.875 2.052,1.031 0.25,0.156 10 false LP

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

·

The engine immobiliser system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the engine immobiliser system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the intelligent tester.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Immobiliser Indicator Security indicator light OFF/ON -
Body Electrical > Entry&Start > Active Test
Tester Display
Immobiliser Indicator
50004 125 28
OK:

The security indicator light operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK SECURITY INDICATOR LIGHT OPERATION

NG

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
2.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

When the immobiliser is set, check that the security indicator light blinks.*1

OK:

The security indicator light blinks normally.



b.

When the theft deterrent system is in the arming preparation state, check that the security indicator light on.*2

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION

OK:

The security indicator light is on normally.



Result:
Result Proceed to
*1 is NG (*2 is OK) A
*2 is NG (*1 is OK) B



A

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I56 security indicator light (heater control switch board) connector.


b.

Disconnect the I86 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I86-8 (IND) - I56-1 (LP) Always Below 1 Ω
I86-8 (IND) - Body ground Always 10 kΩ or higher
I56-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Reconnect the I86 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and check the pulse according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I56-1 (LP) - I56-6 (GND) Power switch off → power switch on (IG) Pulse generation → Below 2 V



Result:
Proceed to
OK
NG



OK

REPLACE SECURITY INDICATOR LIGHT (HEATER CONTROL SWITCH BOARD)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)