Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM
RM2040EQ _58 Vehicle Interior _014730 HEATING / AIR CONDITIONING _0075108 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1475/75  A/C Inverter Cooling / Heating System Malfunction  


DESCRIPTION

The temperature sensor of the compressor with motor assembly detects its inverter temperature.

If the temperature exceeds the maximum, the operation of the compressor with motor assembly will be stopped, and this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1475/75 A/C Inverter Cooling / Heating System Malfunction Temperature of the inverter is outside the specified range (temperature is too high), or there is an open or short to ground in the temperature sensor circuit.
·

Cooling fan system

·

Refrigerant volume

·

Compressor with motor assembly

·

CAN communication system


Memorized

CAUTION / NOTICE / HINT

CAUTION:
·

Wear electrically insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Be sure to carry the removed service plug grip because other workers may install it by mistake.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the intelligent tester to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


e.

Check the operation by referring to the table below.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the Electric Cooling Fan Electric cooling fan OFF or ON -
Powertrain > Engine and ECT > Active Test
Tester Display
Control the Electric Cooling Fan
50004 234 16
OK:

Electric cooling fan operates smoothly.



Result:
Proceed to
OK
NG



OK

3.CHECK REFRIGERANT PRESSURE

NG

3.CHECK REFRIGERANT PRESSURE
a.

b.

Turn the power switch on (READY).


c.
E050573

Read the manifold gauge pressure when the following conditions are established.

i.

Prepare the vehicle according to the chart below.

Item Condition
Vehicle Doors All fully open
Temperature Setting MAX COLD
Blower Speed HI
A/C switch ON
R/F Switch RECIRCULATION
(30 to 35°C (86 to 95°F))

Standard Pressure:
Low pressure side:

0.15 to 0.25 MPa (1.5 to 2.5 kgf/cm2, 21.3 to 35.6 psi)

High pressure side:

1.37 to 1.57 MPa (14 to 16 kgf/cm2, 199 to 228 psi)




Result:
Proceed to
OK
NG



OK

4.READ OUTPUT DTC (DTC B1475/75)

NG

4.READ OUTPUT DTC (DTC B1475/75)
a.

Clear the DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Clear DTCs
50002 121

b.

Power switch on (READY).


c.

Prepare the vehicle according to the table below.

Item Condition
Blower Speed HI
A/C switch ON
Temperature Setting MAX. COLD


d.

Check for DTCs.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR

Body Electrical > Air Conditioner > Trouble Codes
50001 121

Result:
Result Proceed to
DTC B1475/75 is not output (normal) A
DTC B1475/75 is output B


NOTICE:

If the engine keeps idling when ambient temperature is high, the compressor may automatically stop to protect the inverter circuit, and DTC B1475/75 may be stored.



A

SYSTEM IS OK

B

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY