Home › Vehicle Exterior › MIRROR (EXT) › POWER MIRROR CONTROL SYSTEM(w/ Memory)
RM2040EQ _59 Vehicle Exterior _014736 MIRROR (EXT) _0075158 POWER MIRROR CONTROL SYSTEM(w/ Memory) J

MIRROR (EXT)  POWER MIRROR CONTROL SYSTEM(w/ Memory)  Power Mirror Surface Position is not Memorized  


SYSTEM DESCRIPTION

If either the M1 or M2 seat memory switch is pressed, the outer mirror control ECU assembly (driver door) detects the switch operation and sends the seat memory switch signal to the main body ECU (multiplex network body ECU) via CAN communication. On receiving the seat memory switch signal, the main body ECU (multiplex network body ECU) sends the memory request signal to each outer mirror control ECU assembly via CAN communication. When receiving this signal, each outer mirror control ECU assembly stores the mirror surface position based on information from the mirror position sensor, which is built into the mirror sub-assembly.

HINT:

Each mirror sub-assembly has a built-in mirror vertical position sensor and mirror horizontal position sensor.


NOTICE:
·

The mirror surface position will not be memorized if the power switch is not on (IG).

·

The mirror surface position will not be stored if the seat memory SET switch and 2 of the seat memory switches are pressed simultaneously.

·

If the operation fails, the mirror surface position will not be memorized until the seat memory SET switch is turned off.

·

The mirror surface position will not be memorized when the mirror is operated manually.



WIRING DIAGRAM

B313725E11
0.167,6.063 1.365,6.542 1.198,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 0.854,5.219 1.448,5.458 0.594,0.24 10 false CANN 0.625,7.229 2.51,7.49 1.885,0.26 10 false : CAN Communication Line 3.417,6.708 3.958,6.906 0.542,0.198 10 false CANN 3.083,4.906 4.646,5.354 1.563,0.448 10 false Outer Mirror Control ECU Assembly (Driver Door) 5.469,2.198 7.042,2.5 1.573,0.302 10 false Mirror Sub-assembly RH 2.854,7.208 5.073,7.625 2.219,0.417 10 false Outer Mirror Control ECU Assembly (Front Passenger Door) 3.417,3.094 4.125,3.479 0.708,0.385 10 false CANN 0.865,2.615 1.427,2.896 0.563,0.281 10 false CANP 3.427,5.99 3.969,6.25 0.542,0.26 10 false CANP 3.417,1.521 4.052,1.813 0.635,0.292 10 false CANP 4.531,4.302 4.906,4.531 0.375,0.229 10 false J13 4.531,3.875 4.896,4.146 0.365,0.271 10 false J13 4.531,3.438 4.885,3.667 0.354,0.229 10 false J13 4.521,3.01 4.906,3.292 0.385,0.281 10 false J13 3.052,6.708 3.438,6.938 0.385,0.229 10 false K12 3.052,5.969 3.469,6.198 0.417,0.229 10 false K12 4.083,5.792 4.563,6.052 0.479,0.26 10 false LVC 4.073,6.906 4.75,7.167 0.677,0.26 10 false LE1 3.969,6.177 4.531,6.448 0.563,0.271 10 false VSSR 3.979,6.542 4.458,6.771 0.479,0.229 10 false HSSR 4.052,0.333 4.552,0.604 0.5,0.271 10 false RVC 4.083,1.906 4.479,2.135 0.396,0.229 10 false RE1 3.969,0.865 4.479,1.125 0.51,0.26 10 false VSSR 3.969,1.385 4.542,1.635 0.573,0.25 10 false HSSR 4.156,3.01 4.479,3.25 0.323,0.24 10 false M1 4.115,3.875 4.49,4.115 0.375,0.24 10 false MM 3.917,4.302 4.583,4.573 0.667,0.271 10 false MSWE 4.156,3.448 4.51,3.667 0.354,0.219 10 false M2 5.74,3.01 6.135,3.24 0.396,0.229 10 false M1 5.74,3.854 6.198,4.073 0.458,0.219 10 false MRY 5.74,4.292 5.927,4.49 0.188,0.198 10 false E 5.74,3.438 6.083,3.688 0.344,0.25 10 false M2 5.563,2.896 5.823,3.156 0.26,0.26 10 false 4 5.563,3.75 5.771,4 0.208,0.25 10 false 2 5.563,4.188 5.771,4.396 0.208,0.208 10 false 1 5.563,3.333 5.781,3.563 0.219,0.229 10 false 3 4.604,0.104 4.844,0.344 0.24,0.24 10 false 5 4.531,1.885 4.969,2.177 0.438,0.292 10 false z17 4.531,0.313 4.969,0.573 0.438,0.26 10 false z17 4.521,0.833 4.927,1.135 0.406,0.302 10 false z17 4.521,1.354 4.906,1.594 0.385,0.24 10 false z17 4.563,1.667 4.917,2.01 0.354,0.344 10 false 14 3.135,5.76 3.406,6 0.271,0.24 10 false 9 3.125,1.313 3.219,1.448 0.094,0.135 10 false 9 1.354,5.063 1.667,5.302 0.313,0.24 10 false 10 0.167,5.885 0.417,6.021 0.25,0.135 10 false I12 5.604,4.979 6.948,5.323 1.344,0.344 10 false Seat Memory Switch 5.604,4.823 6.104,5.146 0.5,0.323 10 false J16 3.135,6.51 3.375,6.729 0.24,0.219 10 false 8 1.354,2.448 1.625,2.698 0.271,0.25 10 false 9 3.125,2.885 3.219,3.021 0.094,0.135 10 false 8 4.563,4.094 4.885,4.333 0.323,0.24 10 false 13 4.604,0.625 4.802,0.854 0.198,0.229 10 false 6 4.563,1.146 4.854,1.396 0.292,0.25 10 false 13 4.604,2.802 4.802,3.031 0.198,0.229 10 false 2 4.604,3.667 4.844,3.927 0.24,0.26 10 false 1 4.604,3.24 4.802,3.438 0.198,0.198 10 false 3 4.594,5.573 4.823,5.813 0.229,0.24 10 false 5 4.552,6.698 4.875,6.927 0.323,0.229 10 false 14 4.594,5.958 4.813,6.188 0.219,0.229 10 false 6 4.552,6.323 4.854,6.51 0.302,0.188 10 false 13 3.063,3.083 3.469,3.323 0.406,0.24 10 false J13 3.073,1.51 3.458,1.823 0.385,0.313 10 false J13 4.51,6.875 4.958,7.083 0.448,0.208 10 false z16 4.51,5.771 4.969,6.01 0.458,0.24 10 false z16 4.521,6.135 4.99,6.417 0.469,0.281 10 false z16 4.521,6.51 4.938,6.74 0.417,0.229 10 false z16 5.469,7.208 7.01,7.5 1.542,0.292 10 false Mirror Sub-assembly LH

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

OK:

CAN communication DTC is not output.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)

NG

GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART)

2.READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Mirror R / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Mirror R > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 signal ON or OFF ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off
-
Seat Memory Switch2 Seat memory switch M2 signal ON or OFF ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off
-
Seat Memory Switch3 Seat memory switch M3 signal* ON or OFF ON: Seat memory switch M3 on
OFF: Seat memory switch M3 off
Not applicable
Seat Memory Set SW Seat memory switch SET signal ON or OFF ON: Seat memory switch SET on
OFF: Seat memory switch SET off
-
Body Electrical > Mirror R > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Switch3
Seat Memory Set SW
50003 224 1,2,3,4

*: Although the item is displayed on the intelligent tester, it is not applicable to this vehicle.


OK:

The intelligent tester display changes between ON and OFF according to the switch operations.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT MEMORY SWITCH FUNCTION

NG

9.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - OUTER MIRROR CONTROL ECU ASSEMBLY)
3.CHECK SEAT MEMORY SWITCH FUNCTION
a.

When any seat memory switch (M1 or M2 switch) is pressed, check that the driver seat moves to the memorized position.

OK:

The driver seat moves to the memorized position.



Result:
Proceed to
OK
NG



OK

4.CHECK MEMORY AND REACTIVATION FUNCTION

NG

GO TO POWER SEAT CONTROL SYSTEM (Power Seat does not Return to Memorized Position)

4.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C03
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Left Fully


Turn the power switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

Result:
Result Proceed to
Memory and reactivation functions on both mirrors are not normal A
Memory and reactivation functions on RH side mirror are not normal B
Memory and reactivation functions on LH side mirror are not normal C




A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

5.REPLACE MIRROR SUB-ASSEMBLY RH

C

7.REPLACE MIRROR SUB-ASSEMBLY LH
5.REPLACE MIRROR SUB-ASSEMBLY RH
a.

Replace the mirror sub-assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK MEMORY AND REACTIVATION FUNCTION
6.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C04
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Left Fully


Turn the power switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

OK:

Memory and reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (MIRROR SUB-ASSEMBLY RH WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

7.REPLACE MIRROR SUB-ASSEMBLY LH
a.

Replace the mirror sub-assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK MEMORY AND REACTIVATION FUNCTION
8.CHECK MEMORY AND REACTIVATION FUNCTION
a.
B293945C05
0.155,0.062 0.311,0.232 0.156,0.17 10 *a
*a Turn to Left Fully


Turn the power switch on (IG).


b.

Using the outer mirror switch assembly, turn the mirror surface to the fully left position.


c.

Press the M1 switch while the SET switch is being pressed.


d.

Check that the buzzer sounds for 0.5 seconds and the mirror surface position is memorized.


e.

Using the outer mirror switch assembly, turn the mirror surface to the fully right position.


f.

Press the M1 switch.


g.

Check that the buzzer sounds for 0.1 seconds and the outer mirror automatically moves to the recorded fully left position.

OK:

Memory and reactivation function is normal.



Result:
Proceed to
OK
NG



OK

END (MIRROR SUB-ASSEMBLY LH WAS DEFECTIVE)

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (FRONT PASSENGER DOOR)

9.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - OUTER MIRROR CONTROL ECU ASSEMBLY)
a.

Disconnect the J13 connector from the outer mirror control ECU assembly.


b.

Disconnect the J16 connector from the seat memory switch.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J16-2 (MRY) - J13-1 (MM) Always Below 1 Ω
J16-4 (M1) - J13-2 (M1) Always Below 1 Ω
J16-3 (M2) - J13-3 (M2) Always Below 1 Ω
J16-1 (E) - J13-13 (MSWE) Always Below 1 Ω
J16-2 (MRY) - Body ground Always 10 kΩ or higher
J16-4 (M1) - Body ground Always 10 kΩ or higher
J16-3 (M2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT SEAT MEMORY SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT SEAT MEMORY SWITCH
a.
B293836C06
1.817,2.647 1.817,3.082 1.817,3.082 2.286,3.082 false 1.637,2.647 1.637,3.086 1.637,3.086 1.167,3.086 false 0.677,2.502 0.898,2.655 0.221,0.153 10 M1 0.9,3.0 1.121,3.153 0.221,0.153 10 M2 2.344,3.0 2.68,3.153 0.337,0.153 10 MRY 2.533,2.502 2.654,2.655 0.122,0.153 10 E 2.493,2.588 2.054,2.588 false 1.393,2.588 0.954,2.588 false 0.505,1.728 0.663,1.881 0.159,0.153 10 *a
*1 M1 Switch
*2 M2 Switch
*3 SET Switch
*a Component without harness connected
(Seat Memory Switch)


Remove the seat memory switch.

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J16-4 (M1) - J16-1 (E) M1 Switch off → on 10 kΩ or higher → Below 1 Ω
J16-3 (M2) - J16-1 (E) M2 Switch off → on 10 kΩ or higher → Below 1 Ω
J16-2 (MRY) - J16-1 (E) SET Switch off → on 10 kΩ or higher → Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (DRIVER DOOR)

NG

REPLACE SEAT MEMORY SWITCH