Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)
RM2040EQ _58 Vehicle Interior _014728 SEAT _0077333 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat does not Return to Memorized Position  


DESCRIPTION

When either the M1 or M2 switches is pressed, the outer mirror control ECU assembly RH sends a switch signal to the main body ECU (multiplex network body ECU) via CAN communication. Then, the main body ECU (multiplex network body ECU) sends a recall request signal to the position control ECU and switch assembly. The position control ECU and switch assembly operates each motor to achieve each memorized position value.

WIRING DIAGRAM

B293826
1.063,2.25 1.521,2.458 0.458,0.208 10 false CAN 1.063,0.625 1.448,0.854 0.385,0.229 10 false CAN 3.469,0.604 3.792,0.75 0.323,0.146 10 false CAN 3.49,2.365 3.813,2.51 0.323,0.146 10 false GND 3.375,2.802 3.948,3.146 0.573,0.344 10 false J13 4.406,0.458 4.729,0.74 0.323,0.281 10 false M1 4.698,0.344 4.927,0.49 0.229,0.146 10 false 2 4.698,1 4.927,1.146 0.229,0.146 10 false 3 4.698,1.656 4.927,1.802 0.229,0.146 10 false 1 4.698,2.25 5,2.531 0.302,0.281 10 false 13 3.302,2.229 3.479,2.375 0.177,0.146 10 false 7 5.365,0.344 5.531,0.49 0.167,0.146 10 false 4 5.365,1 5.531,1.146 0.167,0.146 10 false 3 5.365,1.656 5.531,1.802 0.167,0.146 10 false 2 5.365,2.25 5.531,2.396 0.167,0.146 10 false 1 5.542,0.344 5.917,0.49 0.375,0.146 10 false M1 5.542,1.01 5.99,1.313 0.448,0.302 10 false M2 5.542,1.656 6.135,1.917 0.594,0.26 10 false MRY 5.552,2.25 5.76,2.427 0.208,0.177 10 false E 4.396,1.115 4.74,1.344 0.344,0.229 10 false M2 4.354,1.781 4.708,2.031 0.354,0.25 10 false MM 4.167,2.375 4.698,2.563 0.531,0.188 10 false MSWE 0.25,1.198 1.823,1.635 1.573,0.438 10 false Position Control ECU and Switch Assembly 0.135,2.792 1.771,3.26 1.635,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 3.365,2.979 4.969,3.354 1.604,0.375 10 false Outer Mirror Control ECU Assembly RH 5.563,2.813 5.906,3.083 0.344,0.271 10 false J16 5.563,2.969 6.969,3.219 1.406,0.25 10 false Seat Memory Switch 0.719,3.458 2.469,3.635 1.75,0.177 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL SYSTEM
a.

Check that each function of the power seat operates normally by using the switches on the power seat switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the switches on the power seat switch.



Result:
Proceed to
OK
NG



OK

2.CHECK SEAT POSITION MEMORY FUNCTION

NG

2.CHECK SEAT POSITION MEMORY FUNCTION
a.

Store a seat position in memory and check that the buzzer sounds to indicate that a position has been stored.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

NOTICE:
·

The seat position will not be recorded if the SET switch and 2 of the memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.



OK:

Seat position memory function is normal.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION RESTORING FUNCTION

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

3.CHECK SEAT POSITION RESTORING FUNCTION
a.

Under each of the following conditions, check that the seat position restoring function operates by pressing the M1 switch or M2 switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK

·

Power switch is off.

·

The power switch is on (IG), and the shift lever is in P.*1

·

The power switch is turned off within 180 seconds after the driver door is closed and opened.*2

·

The power switch is turned off within 60 seconds after the driver door is opened and closed.*3


Result:
Result Proceed to
Seat position restoring function does not operate at all. A
Seat position restoring function does not operate when the condition is *1. B
·

Seat position restoring function does not operate when the condition is *2.

·

Seat position restoring function does not operate when the condition is *3.


C




A

4.READ VALUE USING INTELLIGENT TESTER (SEAT POSITION MEMORY)

B

9.READ VALUE USING INTELLIGENT TESTER (PARK (P) STATE)

C

10.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR COURTESY SWITCH)
4.READ VALUE USING INTELLIGENT TESTER (SEAT POSITION MEMORY)
a.

Store a seat position in memory for each of the M1 and M2 switches.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>OPERATION CHECK


b.

Connect the intelligent tester to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the intelligent tester on.


e.

Enter the following menus: Body / Driver Seat / Data List.


f.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Body Electrical > Driver Seat > Data List
Tester Display
Seat Memory No1
Seat Memory No2
50003 162 3,4
OK:

Mem appears on the intelligent tester screen.



Result:
Proceed to
OK
NG



OK

5.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

5.REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH
a.

Replace the outer mirror control ECU assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK SEAT POSITION RESTORING FUNCTION
6.CHECK SEAT POSITION RESTORING FUNCTION

b.

Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

NOTICE:
·

The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.

·

If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.



OK:

Seat position restoring function operates normally.



Result:
Proceed to
OK
NG



OK

END (OUTER MIRROR CONTROL ECU ASSEMBLY RH WAS DEFECTIVE)

NG

7.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
7.REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY
a.

Replace the position control ECU and switch assembly.

Click hereVehicle Interior>SEAT>POWER SEAT SWITCH(w/ Seat Position Memory System)>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CHECK SEAT POSITION RESTORING FUNCTION
8.CHECK SEAT POSITION RESTORING FUNCTION


c.

Check that the buzzer sounds for 0.1 seconds and the seat automatically moves to the memorized position.

NOTICE:
·

The seat will not return to the memorized position if 2 of the seat memory switches are pressed simultaneously.

·

If a restoring operation has failed, release all switches. The seat memory restoring function does not operate unless the switches are released.



OK:

Seat position restoring function operates normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU AND SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

9.READ VALUE USING INTELLIGENT TESTER (PARK (P) STATE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Driver Seat / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P sw(PMN) Park state signal ON or OFF ON: Shift lever in P
OFF: Shift lever in a position other than P
-
Body Electrical > Driver Seat > Data List
Tester Display
Shift P sw(PMN)
50003 162 193
OK:

On the intelligent tester screen, the item changes between ON and OFF according to the above.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

10.READ VALUE USING INTELLIGENT TESTER (DRIVER DOOR COURTESY SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy Front door courtesy light switch assembly signal ON or OFF ON: Driver door open
OFF: Driver door closed
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
50003 123 197
OK:

On the intelligent tester screen, the item changes between ON and OFF according to the above.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY

NG

GO TO LIGHTING SYSTEM (Front Door Courtesy Switch Circuit)