| U0100
|
Lost Communication with ECM / PCM "A"
|
The power management control ECU does not receive data from the ECM.
|
·
Open or short in sub bus 15 main line or connector
·
Open or short in sub bus 15 branch line or connector
·
Power source circuit of power management control ECU
·
Power management control ECU
·
Power source circuit of ECM
·
Open or short in CAN No. 1 junction connector
|
As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs.
|
|
| U0129
|
Lost Communication with Brake System Control Module
|
The power management control ECU does not receive data from the brake booster with master cylinder assembly (skid control ECU).
|
·
Open or short in sub bus 15 main line or connector
·
Open or short in sub bus 15 branch line or connector
·
Power source circuit of power management control ECU
·
Power management control ECU
·
Power source circuit of brake booster with master cylinder assembly (skid control ECU)
·
Brake booster with master cylinder assembly (skid control ECU)
·
Open or short in CAN No. 1 junction connector
|
As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs.
|
|
| U0129
|
Lost Communication with Brake System Control Module
|
No communication from the brake booster with master cylinder assembly (skid control ECU) continues.
|
·
Brake booster with master cylinder assembly (skid control ECU) branch line or connector
·
Power source circuit of brake booster with master cylinder assembly (skid control ECU)
·
Brake booster with master cylinder assembly (skid control ECU) ground circuit
·
Brake booster with master cylinder assembly (skid control ECU)
|
As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs.
|
|
| U0199
|
Lost Communication with "Door Control Module A"
|
No communication from the outer mirror control ECU assembly continues.
|
·
Outer mirror control ECU assembly (for driver side) branch line or connector
·
Power source circuit of outer mirror control ECU assembly (for driver side)
·
Outer mirror control ECU assembly (for driver side) ground circuit
·
Outer mirror control ECU assembly (for driver side)
|
The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.
|
|
| U0200
|
Lost Communication with "Door Control Module B"
|
No communication from the outer mirror control ECU assembly continues.
|
·
Outer mirror control ECU assembly (for front passenger side) branch line or connector
·
Power source circuit of outer mirror control ECU assembly (for front passenger side)
·
Outer mirror control ECU assembly (for front passenger side) ground circuit
·
Outer mirror control ECU assembly (for front passenger side)
|
The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.
|
|
| U0208
|
Lost Communication with "Seat Control Module A"
|
No communication from the position control ECU and switch assembly continues.
|
·
Position control ECU and switch assembly (for driver side) branch line or connector
·
Power source circuit of position control ECU and switch assembly (for driver side)
·
Position control ECU and switch assembly (for driver side) ground circuit
·
Position control ECU and switch assembly (for driver side)
|
The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.
|
|
| U0232
|
Lost Communication with Blind Spot Monitor Slave Module
|
No communication from the blind spot monitor sensor LH continues.
|
·
Blind spot monitor sensor LH branch line or connector
·
Power source circuit of blind spot monitor sensor LH
·
Blind spot monitor sensor LH ground circuit
·
Blind spot monitor sensor LH
|
The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11.
|
|
| U0233
|
Lost Communication with Blind Spot Monitor Master Module
|
No communication from the blind spot monitor sensor RH continues.
|
·
Blind spot monitor sensor RH branch line or connector
·
Power source circuit of blind spot monitor sensor RH
·
Blind spot monitor sensor RH ground circuit
·
Blind spot monitor sensor RH
|
The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11.
|
|
| U0293
|
Lost Communication with HV ECU
|
·
The ECM does not receive data from the power management control ECU.
·
The brake booster with master cylinder assembly (skid control ECU) does not receive data from the power management control ECU.
|
·
Open or short in sub bus 15 main line or connector
·
Open or short in sub bus 15 branch line or connector
·
Power source circuit of ECM
·
Power source circuit of power management control ECU
·
Power management control ECU
·
Power source circuit of brake booster with master cylinder assembly (skid control ECU)
·
Brake booster with master cylinder assembly (skid control ECU)
·
Open or short in CAN No. 1 junction connector
|
As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs.
|
|
| U1002
|
Lost Communication with Gateway Module
|
The power management control ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 11.
|
·
Open or short in sub bus 11 main line or connector
·
Open or short in sub bus 11 branch line or connector
·
Power management control ECU
·
Blind spot monitor sensor LH
·
Blind spot monitor sensor RH
·
Open or short in CAN No. 2 junction connector
·
Open or short in CAN No. 3 junction connector
·
Open or short in CAN No. 4 junction connector
|
The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11.
|
|
| U1002
|
Lost Communication with Gateway Module (Main Body ECU)
|
Main body ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 1.
|
·
Open or short in sub bus 1 main line or connector
·
Open or short in sub bus 1 branch line or connector
·
Main body ECU (Multiplex network body ECU)
·
Outer mirror control ECU assembly (for Driver side)
·
Outer mirror control ECU assembly (for Front passenger side)
·
Position control ECU and switch assembly (for Driver side)
·
Open or short in CAN junction LH2 connector
·
Open or short in CAN junction RH2 connector
|
The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1.
|
|