Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1345/66  Linear Solenoid Valve Offset Learning Undone  C1368/67  Linear Solenoid Valve Offset Malfunction  


DESCRIPTION

The skid control ECU stores and corrects the individual differences in the brake pedal stroke sensor assembly, actuator solenoids, and stroke simulator solenoid. Perform initialization and calibration of the linear solenoid valve if any of these parts is replaced.

The skid control ECU receives the shift position P signal from the power management control ECU through the CAN communication system.

The DTCs are cleared when the linear valve offset learning results are normal.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1345/66 Linear Solenoid Valve Offset Learning Undone - Linear valve offset learning undone. Perform linear valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal. Electronically controlled brake system DTC
C1368/67 Linear Solenoid Valve Offset Malfunction - Offset learned value out of specification.
·

Perform linear valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal.

·

Brake actuator (Brake booster with master cylinder assembly)


Electronically controlled brake system DTC

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


HINT:

When C1451/72 is output together with C1345/66 and/or C1368/67, inspect and repair the trouble areas indicated by C1451/72 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>C1451/72


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch off.


c.

Turn the power switch on (IG).


d.

Check the DTCs (electronically controlled brake system and hybrid control system) that are output.

for Electronically Controlled Brake System: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

for Hybrid Control System: Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Powertrain > Hybrid Control > Trouble Codes
50001 236
Result:
Result Proceed to
DTCs (except C1345/66, C1368/67 and hybrid control system DTCs) are not output. A
Hybrid control system DTC is output. B
DTCs (except C1345/66 and/or C1368/67) are output. C


HINT:

Before performing initialization and calibration of the linear solenoid valve, C1203/95 will be output.




A

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE

B

C

2.PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE
a.

Turn the power switch off.


b.

Perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION

Chassis > ABS/VSC/TRC > Utility
Tester Display
ECB Utility
50005 105 167

Result:
Proceed to
NEXT



NEXT

3.RECONFIRM DTC
3.RECONFIRM DTC
a.

Turn the power switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (IG).


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
DTCs C1345/66 and C1368/67 are not output. A
DTCs C1345/66 and/or C1368/67 are output. B



A

END

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY