Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1241/41  Low Battery Positive Voltage  C1242/42  Open in IG1 / IG2 Power Source Circuit  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU power source voltage drops, or there is insufficient voltage to operate the ABS main relay, the skid control ECU will store these DTCs.

These DTCs may also be stored if the auxiliary battery voltage drops below 9.5 V.

HINT:

DTC C1256/56 (Accumulator Low Pressure) may also be memorized if there is a drop in power source voltage.


DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1241/41 Low Battery Positive Voltage 101*1
102*1
551*2
552*2
553*2
·

INF Code: 101

·

Any of the following conditions when the BS terminal voltage is 9.3 V or less:

1.

Vehicle not decelerated (brake pedal is not depressed) for 3 seconds or more.

2.

While depressing the brake pedal, linear solenoid current does not satisfy 1.34 A.

3.

Vehicle decelerated (brake pedal is depressed) for 0.06 seconds.



·

INF Code: 102

·

Either of the following conditions when the ECU internal voltage is 6.3 V or less:

1.

When main relay ON is requested, voltage of the relay connection does not exceed 3.5 V for 0.22 seconds or more.

2.

Sensor supply voltage is 4.75 V or less, or 5.25 V or more for 0.06 seconds.

3.

Accumulator pressure sensor output voltage is 4.54 V or less, or 5.46 V or more for 0.06 seconds.



·

INF Code: 551

·

When driving at 3 km/h (1.9 mph) or more, IG1 terminal voltage is 9.5 V or less, or VM1 voltage is 8.6 V or less for 10 seconds or more.


·

INF Code: 552

·

When VM1 voltage is 8.6 V or less, sensor supply voltage is low for 60 seconds or more.


·

INF Code: 553

·

VM1 voltage is 16.6 V or more for 0.8 seconds.



·

Improperly connected connector, deformation or corrosion of terminals

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Skid control ECU (Brake booster with master cylinder assembly)


*1: Electronically controlled brake system DTC
*2: ABS DTC
C1242/42 Open in IG1 / IG2 Power Source Circuit 111
112
·

INF Code: 111

·

Voltage is not applied to the IG1 terminal (less than 3.5 V), and applied to the IG2 terminal (9.5 V or more) for 4 seconds or more.


·

INF Code: 112

·

Voltage is not applied to the IG2 terminal (less than 3.5 V), and applied to the IG1 terminal (9.5 V or more) for 4 seconds or more.



·

INF Code: 111

·

Open or short in IG1 circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Smart entry and start system (IG start circuit)

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Skid control ECU (Brake booster with master cylinder assembly)


·

INF Code: 112

·

Open or short in IG2 circuit

·

Improperly connected connector, deformation or corrosion of terminals

·

Smart entry and start system (IG start circuit)

·

Auxiliary battery

·

Hybrid control system (Charging circuit)

·

Skid control ECU (Brake booster with master cylinder assembly)



Electronically controlled brake system DTC

WIRING DIAGRAM

C279472E02
0.583,0.802 2,0.969 1.417,0.167 10 false from Auxiliary Battery 0.594,2 2.49,2.365 1.896,0.365 10 false from IG1 NO. 2 Relay 0.99,2.594 1.99,2.76 1,0.167 10 false from IG2 Relay 3.917,0.958 4.75,1.125 0.833,0.167 10 false ABS NO. 2 3.917,1.552 4.75,1.719 0.833,0.167 10 false ABS NO. 1 3.813,2.125 5.083,2.417 1.271,0.292 10 false ECU-IG1 NO. 1 3.844,2.75 5.063,3.01 1.219,0.26 10 false ECU-IG2 NO. 2 5.938,0.813 6.188,0.979 0.25,0.167 10 false BI 5.938,1.406 6.188,1.573 0.25,0.167 10 false BS 5.938,2 6.188,2.167 0.25,0.167 10 false IG1 5.938,2.594 6.188,2.76 0.25,0.167 10 false IG2 5.927,3.198 6.344,3.365 0.417,0.167 10 false GND 5.927,4.333 6.344,4.5 0.417,0.167 10 false GND3 5.927,3.76 6.344,3.927 0.417,0.167 10 false GND2 5.927,4.927 6.344,5.094 0.417,0.167 10 false GND4 5.927,5.51 6.344,5.677 0.417,0.167 10 false GND5 5.927,6.083 6.344,6.25 0.417,0.167 10 false GND6 5.063,6.875 5.479,7.042 0.417,0.167 10 false A28 5.063,7.042 7.156,7.375 2.094,0.333 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.635,0.708 5.885,0.875 0.25,0.167 10 false 14 5.635,1.302 5.885,1.469 0.25,0.167 10 false 15 5.635,1.896 5.885,2.063 0.25,0.167 10 false 16 5.635,2.5 5.885,2.667 0.25,0.167 10 false 12 5.635,3.094 5.885,3.26 0.25,0.167 10 false 28 5.635,3.656 5.885,3.823 0.25,0.167 10 false 27 5.635,4.219 5.885,4.385 0.25,0.167 10 false 26 5.635,4.823 5.885,4.99 0.25,0.167 10 false 25 5.635,5.406 5.885,5.573 0.25,0.167 10 false 24 5.635,5.99 5.885,6.156 0.25,0.167 10 false 23 4.469,0.708 4.635,0.875 0.167,0.167 10 false 2 3.99,0.708 4.156,0.875 0.167,0.167 10 false 1 4.469,1.896 4.635,2.063 0.167,0.167 10 false 2 4.469,2.5 4.635,2.667 0.167,0.167 10 false 2 3.99,1.896 4.156,2.063 0.167,0.167 10 false 1 3.99,2.5 4.156,2.667 0.167,0.167 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK SMART ENTRY AND START SYSTEM (for Start Function)
a.

Check if smart entry and start system (for start function) DTCs are output.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125

Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.CHECK HYBRID CONTROL SYSTEM

B

2.CHECK HYBRID CONTROL SYSTEM
a.

Check if hybrid control system DTCs are output.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 236

Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

3.CHECK DTC

B

3.CHECK DTC
a.

Check that no main relay DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Main relay malfunction DTC is not output. A
Main relay malfunction DTC is output. B



A

4.CHECK AUXILIARY BATTERY

B

4.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

CHARGE OR REPLACE AUXILIARY BATTERY

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C249762C40
0.208,0.802 0.625,1.073 0.417,0.271 1.344,1.875 1.083,2.719 false 2.635,1.844 2.865,2.719 false 2.708,0.844 2.458,1.667 false 2.083,0.802 2.26,1.667 false 0.198,0.188 0.406,0.344 0.208,0.156 10 false *a 0.313,0.854 0.906,1.229 0.594,0.375 10 false A28 0.979,2.75 1.563,3.188 0.583,0.438 10 false IG1 2.792,2.75 3.375,3.188 0.583,0.438 10 false BS 2.677,0.615 3.26,1.052 0.583,0.438 10 false BI 1.948,0.604 2.531,1.042 0.583,0.438 10 false IG2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-14 (BI) - Body ground Always 11 to 14 V
A28-15 (BS) - Body ground Always 11 to 14 V
A28-16 (IG1) - Body ground Power switch on (IG) 11 to 14 V
A28-12 (IG2) - Body ground Power switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C249762C41
0.208,0.802 0.625,1.073 0.417,0.271 2.052,0.479 2.156,1.792 false 2.667,2.031 2.896,2.906 false 2.823,0.927 2.458,1.792 false 2.677,0.458 2.375,1.781 false 2.281,0.844 2.26,1.792 false 1.75,0.865 2.031,1.781 false 0.198,0.188 0.406,0.344 0.208,0.156 10 false *a 0.302,0.854 0.719,1.219 0.417,0.365 10 false A28 1.875,0.292 2.458,0.729 0.583,0.438 10 false GND5 2.802,2.938 3.385,3.375 0.583,0.438 10 false GND 2.708,0.75 3.292,1.188 0.583,0.438 10 false GND2 2.583,0.25 3.167,0.688 0.583,0.438 10 false GND3 2.146,0.646 2.729,1.083 0.583,0.438 10 false GND4 1.531,0.667 2.115,1.104 0.583,0.438 10 false GND6
*a Front view of wire harness connector (to Skid Control ECU (Brake Booster with Master Cylinder Assembly))


Turn the power switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-28 (GND) - Body ground Always Below 1 Ω
A28-27 (GND2) - Body ground Always Below 1 Ω
A28-26 (GND3) - Body ground Always Below 1 Ω
A28-25 (GND4) - Body ground Always Below 1 Ω
A28-24 (GND5) - Body ground Always Below 1 Ω
A28-23 (GND6) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

7.RECONFIRM DTC
a.

Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1241/41 and C1242/42 are not output. A
DTCs C1241/41 and/or C1242/42 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY