Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014700 CRUISE CONTROL _0166042 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A41  Brake Request Value Mismatch between ENG / EHV and Driving Support ECU  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) receives brake control request signals from the power management control ECU and driving support ECU assembly.

When the request signals received from the power management control ECU and driving support ECU assembly are not consistent, the skid control ECU (brake booster with master cylinder assembly) determines that a malfunction has occurred and sends a malfunction signal to the driving support ECU assembly.

If the driving support ECU assembly receives a malfunction signal, DTC C1A41 is output. Although the brake booster with master cylinder assembly sends a malfunction signal to the driving support ECU assembly, the electronically controlled brake system does not output a relevant malfunction detection DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A41 Brake Request Value Mismatch between ENG / EHV and Driving Support ECU While the power switch is on (IG), the brake booster with master cylinder assembly detects a significant difference in the brake request signal from the power management control ECU and driving support ECU assembly for 0.992 seconds or more while the vehicle is being driven at a speed of 36 km/h (22 mph) or more.
·

Electronically controlled brake system

·

Hybrid control system

·

Power management control ECU

·

Skid control ECU (Brake booster with master cylinder assembly)

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.


PROCEDURE

1.CHECK FOR DTCS (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


e.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output A
Electronically controlled brake system DTCs are output B



A

2.CHECK FOR DTCS (HYBRID CONTROL SYSTEM)

B

2.CHECK FOR DTCS (HYBRID CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check for DTCs.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Hybrid Control > Trouble Codes
50001 236

Result:
Result Proceed to
Hybrid control system DTCs are not output A
Hybrid control system DTCs are output B



A

3.CHECK FOR DTCS (DTC C1A41)

B

3.CHECK FOR DTCS (DTC C1A41)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 197

e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.



f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A41 is not output A
DTC C1A41 is output B



A

B

4.REPLACE DRIVING SUPPORT ECU ASSEMBLY
4.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCS (DTC C1A41)
5.CHECK FOR DTCS (DTC C1A41)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 197

e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.



f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A41 is not output A
DTC C1A41 is output B



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

6.REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
6.REPLACE SKID CONTROL ECU (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY)
a.

Replace the skid control ECU (brake booster with master cylinder assembly) with a new one.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTCS (DTC C1A41)
7.CHECK FOR DTCS (DTC C1A41)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Clear DTCs
50002 197

e.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed for which dynamic radar cruise control system operation is possible.


ii.

Turn the cruise control system on using the cruise control main switch (ON-OFF button).


iii.

Push the cruise control main switch to -/SET to begin control of vehicle speed using the cruise control system.



f.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

Powertrain > Radar Cruise > Trouble Codes
50001 197

Result:
Result Proceed to
DTC C1A41 is not output A
DTC C1A41 is output B



A

END (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY WAS DEFECTIVE)

B