Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _035749 PRE-CRASH SAFETY _0166048 PRE-CRASH SAFETY SYSTEM Y

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the pre-crash safety system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT AUXILIARY BATTERY VOLTAGE
2.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the power switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.


Result:
Proceed to
OK
NG



OK

3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*

NG

CHARGE OR REPLACE AUXILIARY BATTERY

3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*


c.

Connect the GTS to the DLC3.


d.

Turn the power switch on (IG).


e.

Turn the GTS on.


f.

Turn the cruise control switch (ON/OFF button) on.


g.

Enter the following menus: Powertrain / Radar Cruise / Utility / Beam Axis Misalignment Reading.


h.

Check the amount of misalignment and make a note.

Powertrain > Radar Cruise > Utility
Tester Display
Beam Axis Misalignment Reading
50005 197 4260

Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B




A

5.CHECK FOR DTCS (PRE-CRASH 2)*

B

5.CHECK FOR DTCS (PRE-CRASH 2)*
a.

Clear the DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Clear DTCs
50002 220

b.

Check for DTCs.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Crash 2 > Trouble Codes
50001 220
Result:
Result Proceed to
DTCs are not output (symptoms can be confirmed or reproduced) A
DTCs are not output (symptoms cannot be confirmed or reproduced) B
DTCs are output C




A

6.PROBLEM SYMPTOMS TABLE

B

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

C

6.PROBLEM SYMPTOMS TABLE
HINT:

Refer to Problem Symptoms Table.

Click hereVehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>PROBLEM SYMPTOMS TABLE


Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B



A

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

ADJUST, REPAIR OR REPLACE IN ACCORDANCE WITH PROBLEM SYMPTOMS TABLE

7.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

8.ADJUST, REPAIR OR REPLACE
8.ADJUST, REPAIR OR REPLACE
NOTICE:

If the millimeter wave radar sensor assembly is replaced, the beam axis of the sensor needs to be adjusted.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


HINT:

Perform proper procedures according to corresponding faults listed in the problem symptoms table or the corresponding DTCs listed in the diagnostic trouble code chart.


Result:
Proceed to
NEXT



NEXT

9.CONFIRMATION TEST
9.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END