Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM J

2AR-FXE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the power switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually: When the power switch is turned on (IG), the MIL should be illuminated and should turn off after power switch on (READY). If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A337292E01
5.938,3.771 6.396,3.969 0.458,0.198 10 false A25 6.302,3.771 6.76,3.969 0.458,0.198 10 false ECM 5.813,0.75 6.271,0.948 0.458,0.198 10 false 30 6.052,0.75 6.51,0.948 0.458,0.198 10 false W 5.302,0.656 5.76,0.854 0.458,0.198 10 false 12 5.292,0.844 5.75,1.042 0.458,0.198 10 false I17 4.896,0.979 5.354,1.177 0.458,0.198 10 false CHK 4.354,0.99 4.813,1.188 0.458,0.198 10 false IG+ 4.052,0.844 4.51,1.042 0.458,0.198 10 false I18 4.052,0.667 4.51,0.865 0.458,0.198 10 false 13 4.198,1.365 5.365,1.823 1.167,0.458 10 false Combination Meter Assembly 3.302,1.01 4.469,1.469 1.167,0.458 10 false METER-IG2 2.896,0.844 3.354,1.042 0.458,0.198 10 false 1C 2.948,0.667 3.177,0.938 0.229,0.271 10 false 5 2.74,2 3.198,2.198 0.458,0.198 10 false 1C 2.854,1.823 3.083,2.094 0.229,0.271 10 false 8 1.646,1.49 1.948,1.75 0.302,0.26 10 false IG2 1.219,2.219 2.844,2.49 1.625,0.271 10 false No. 1 Integration Relay 0.99,2.01 1.448,2.208 0.458,0.198 10 false 1E 1.104,1.823 1.333,2.094 0.229,0.271 10 false 2 1.948,3.26 2.344,3.51 0.396,0.25 10 false IG2D 2.313,3.146 2.708,3.396 0.396,0.25 10 false 2 1.49,3.74 1.885,3.99 0.396,0.25 10 false A39 1.469,3.885 2.729,4.448 1.26,0.563 10 false Power Management Control ECU 0.188,2.01 0.646,2.208 0.458,0.198 10 false 1D 0.323,1.833 0.552,2.104 0.229,0.271 10 false 3 0.354,2.531 1.104,2.781 0.75,0.25 10 false IG2-MAIN 0.354,3.115 1.104,3.365 0.75,0.25 10 false MAIN 0.479,3.708 1.052,4.271 0.573,0.563 10 false Auxiliary Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.


Result:
Result Proceed to
MIL remains ON A
MIL does not illuminate B



A

2.CHECK WHETHER DTC OUTPUT RECURS

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check if any DTCs have been detected. Note down any DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC is not detected A
Any DTCs are detected B


HINT:

Check for detected DTCs output from other ECUs which relate to the MIL.



A

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.
A255690C50
0.583,0.969 0.99,1.25 0.406,0.281 0.177,0.135 0.521,0.396 0.344,0.26 10 false *a 0.667,1.031 1.073,1.313 0.406,0.281 10 false A25
*a Front view of wire harness connector
(to ECM)


Disconnect the A25 ECM connector.


b.

Turn the power switch on (IG).


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-12 (CHK) or A25-30 (W) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the power switch is turned on (IG).

OK:

MIL should be illuminated.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

e.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The GTS cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-12 (CHK) - A25-30 (W) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR