Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U1002  Lost Communication with Gateway Module (Power Management1)  


DESCRIPTION

·

The power management control ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to sub bus 11.

·

When the power management control ECU receives a response signal from the ECUs connected to sub bus 11, the power management control ECU recognizes and memorizes that the ECU is connected to sub bus 11. Based on this memorized data, the power management control ECU monitors for malfunctions in the ECUs connected to sub bus 11 when communicating with those ECUs. If the power management control ECU cannot receive response signals from the ECUs that have been memorized as those connected to sub bus 11, the power management control ECU determines that a malfunction exists.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
U1002 Lost Communication with Gateway Module The power management control ECU cannot receive signals from all ECUs that have been memorized as those connected to sub bus 11.
·

Open or short in sub bus 11 main lines or connector

·

Short in sub bus 11 branch lines or connector

·

Power management control ECU

·

Lane departure warning camera

(w/ Lane Departure Alert System)

·

Driving support ECU assembly

(w/ Pre-crash Safety System)

·

Blind spot monitor sensor RH

(w/ Blind Spot Monitor System)

·

Rear television camera assembly

(w/ Parking Assist Monitor System without Parallel Parking Assist Function)

·

Open or short in CAN No. 2 junction connector

·

Open or short in CAN No. 3 junction connector

·

Open or short in CAN No. 4 junction connector

·

Open or short in CAN No. 5 junction connector

·

Open or short in CAN No. 6 junction connector


The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11.

HINT:

This diagnostic procedure is for when DTC U1002 is output by the power management control ECU (GTS display: PM1 Gateway).


WIRING DIAGRAM

C325242E01
0.083,0.052 2.104,0.292 2.021,0.24 12 false Sub Bus 11: 1.125,0.323 1.396,0.594 0.271,0.271 10 false I3 1.323,0.323 2.573,0.781 1.25,0.458 10 false Power Management Control ECU 3.365,0.167 3.802,0.448 0.438,0.281 10 false 120 Ω 3.385,7.688 3.823,7.969 0.438,0.281 10 false 120 Ω 0.948,8.031 2.833,8.292 1.885,0.26 10 false : CAN Main Bus Line (CANH) 0.948,8.438 2.833,8.698 1.885,0.26 10 false : CAN Main Bus Line (CANL) 3.594,8.01 5.479,8.271 1.885,0.26 10 false : CAN Branch Line (CANH) 3.594,8.417 5.479,8.677 1.885,0.26 10 false : CAN Branch Line (CANL) 2.719,7.271 3.156,7.552 0.438,0.281 10 false CANL 4.042,7.281 4.479,7.563 0.438,0.281 10 false CANH 4.583,7.51 5.021,7.792 0.438,0.281 10 false T16 4.917,7.51 6.802,7.771 1.885,0.26 10 false CAN No. 4 Junction Connector 3.042,7.042 3.333,7.292 0.292,0.25 10 false 2 4.052,7.042 4.344,7.292 0.292,0.25 10 false 3 4.063,6.792 4.354,7.042 0.292,0.25 10 false L 2.979,6.781 3.271,7.031 0.292,0.25 10 false B 2.979,6.5 3.271,6.75 0.292,0.25 10 false 12 4.01,6.49 4.302,6.74 0.292,0.25 10 false 1 0.375,6.615 2.844,6.885 2.469,0.271 10 false Rear Television Camera Assembly*4 0.917,4.885 2.802,5.146 1.885,0.26 10 false CAN No. 2 Junction Connector 4.438,6.25 4.875,6.531 0.438,0.281 10 false T15 0.104,6.615 0.396,6.865 0.292,0.25 10 false T22 1.021,6.333 1.458,6.615 0.438,0.281 10 false CANL 1,5.823 1.438,6.104 0.438,0.281 10 false CANH 1.49,5.833 1.781,6.083 0.292,0.25 10 false 4 1.479,6.344 1.771,6.594 0.292,0.25 10 false 1 2.052,6.417 2.344,6.667 0.292,0.25 10 false P 2.042,5.74 2.333,5.99 0.292,0.25 10 false V 2.667,6.344 2.958,6.594 0.292,0.25 10 false 13 2.708,5.823 3,6.073 0.292,0.25 10 false 2 2.969,5.708 3.26,5.958 0.292,0.25 10 false 14 4.021,5.719 4.313,5.969 0.292,0.25 10 false 3 2.99,5.385 3.281,5.635 0.292,0.25 10 false B 4.063,5.396 4.354,5.646 0.292,0.25 10 false G 4.01,5.177 4.302,5.427 0.292,0.25 10 false 8 2.979,5.188 3.271,5.438 0.292,0.25 10 false 19 4.313,4.563 4.604,4.813 0.292,0.25 10 false 9 4.313,5.052 4.604,5.302 0.292,0.25 10 false 20 5.073,5.135 5.365,5.385 0.292,0.25 10 false B 5.052,4.49 5.344,4.74 0.292,0.25 10 false R 5.427,5.333 5.813,5.563 0.385,0.229 10 false O47 5.74,5.323 6.885,5.74 1.146,0.417 10 false Blind Spot Monitor Sensor RH*3 5.552,5.052 5.844,5.302 0.292,0.25 10 false 7 5.563,4.552 5.854,4.802 0.292,0.25 10 false 2 5.771,4.552 6.208,4.833 0.438,0.281 10 false CA1P 5.76,5.063 6.198,5.344 0.438,0.281 10 false CA1N 4.74,6.24 6.625,6.5 1.885,0.26 10 false CAN No. 3 Junction Connector 0.604,4.885 1.042,5.167 0.438,0.281 10 false O30 2.969,4.458 3.26,4.708 0.292,0.25 10 false 22 4,4.458 4.292,4.708 0.292,0.25 10 false 11 4.073,4.281 4.365,4.531 0.292,0.25 10 false V 4.073,3.792 4.365,4.042 0.292,0.25 10 false V 2.969,4.292 3.26,4.542 0.292,0.25 10 false B 2.885,3.792 3.177,4.042 0.292,0.25 10 false LG 4.167,3.521 4.458,3.771 0.292,0.25 10 false 1 4.177,2.729 4.469,2.979 0.292,0.25 10 false 1 2.656,2.771 2.948,3.021 0.292,0.25 10 false 1 2.875,3.531 3.167,3.781 0.292,0.25 10 false 2 2.656,3.521 2.948,3.771 0.292,0.25 10 false 2 2.896,2.719 3.188,2.969 0.292,0.25 10 false 2 3.052,3.521 3.344,3.771 0.292,0.25 10 false I178 3.813,3.51 4.104,3.76 0.292,0.25 10 false I178 3.813,2.729 4.104,2.979 0.292,0.25 10 false I180 3.063,2.729 3.354,2.979 0.292,0.25 10 false I180 2.563,3.292 2.854,3.542 0.292,0.25 10 false I179 2.563,2.979 2.854,3.229 0.292,0.25 10 false I179 2,3.49 2.292,3.74 0.292,0.25 10 false LG 2.052,2.813 2.344,3.063 0.292,0.25 10 false L 1.469,2.875 1.76,3.125 0.292,0.25 10 false 39 1.479,3.406 1.771,3.656 0.292,0.25 10 false 17 1.021,2.875 1.458,3.156 0.438,0.281 10 false CA2H 1.01,3.396 1.448,3.677 0.438,0.281 10 false CA2L 0.094,3.667 0.438,3.885 0.344,0.219 10 false I176 0.417,3.667 2.604,4.083 2.188,0.417 10 false Driving Support ECU Assembly*2 4.375,3.25 6.26,3.51 1.885,0.26 10 false CAN No. 6 Junction Connector 0.552,7.385 1.802,7.708 1.25,0.323 10 false x: Suspected Area 4.344,1.979 4.635,2.229 0.292,0.25 10 false S16 4.635,1.979 6.521,2.24 1.885,0.26 10 false CAN No. 5 Junction Connector 4.083,2.375 4.375,2.625 0.292,0.25 10 false R 2.906,2.417 3.198,2.667 0.292,0.25 10 false LG 4.01,2.188 4.302,2.438 0.292,0.25 10 false 2 3.031,2.188 3.323,2.438 0.292,0.25 10 false 8 2.74,1.51 3.031,1.76 0.292,0.25 10 false 1 2.729,2.031 3.021,2.281 0.292,0.25 10 false 7 4.021,1.365 4.313,1.615 0.292,0.25 10 false 3 3.052,1.375 3.344,1.625 0.292,0.25 10 false 9 2.042,1.448 2.333,1.698 0.292,0.25 10 false V 2,2.135 2.292,2.385 0.292,0.25 10 false LG 1.031,1.521 1.469,1.802 0.438,0.281 10 false CA1P 1.01,2.042 1.448,2.323 0.438,0.281 10 false CA1N 1.5,1.51 1.792,1.76 0.292,0.25 10 false 6 1.49,2.031 1.781,2.281 0.292,0.25 10 false 12 0.063,2.302 0.354,2.552 0.292,0.25 10 false S15 0.354,2.302 2.542,2.719 2.188,0.417 10 false Lane Departure Warning Camera*1 2.896,1.073 3.188,1.323 0.292,0.25 10 false LG 4.052,1.073 4.344,1.323 0.292,0.25 10 false B 2.969,0.833 3.26,1.083 0.292,0.25 10 false 34 4.01,0.833 4.302,1.083 0.292,0.25 10 false 35 4.042,0.604 4.479,0.885 0.438,0.281 10 false CA2H 2.75,0.615 3.188,0.896 0.438,0.281 10 false CA2L 4.615,0.094 7.01,0.375 2.396,0.281 10 false *1: w/ Lane Departure Alert System 4.625,0.417 7.021,0.698 2.396,0.281 10 false *2: w/ Pre-crash Safety System 4.625,0.74 7.021,1.021 2.396,0.281 10 false *3: w/ Blind Spot Monitor System 4.625,1.104 7.063,1.604 2.438,0.5 10 false *4: w/ Parking Assist Monitor System without Parallel Parking Assist Function

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), wait at least 52 seconds and then drive the vehicle at a speed of 36 km/h (22 mph) or more for at least 11.84 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK SUB BUS 11
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
A261175C45
1.813,0.583 2.313,0.875 0.5,0.292 1.604,1.083 1.698,1.083 1.698,1.083 1.823,1.688 true 2.552,1.083 2.448,1.083 2.448,1.083 2.229,1.688 true 1.531,2.917 1.625,2.917 1.625,2.917 1.813,1.906 true 2.167,2.906 2.083,2.906 2.083,2.906 1.865,1.906 true 0.063,0.021 0.271,0.24 0.208,0.219 10 false *a 2.573,1 2.99,1.156 0.417,0.156 10 false AM22 1.375,1 1.573,1.156 0.198,0.156 10 false E1 1.99,0.635 2.167,0.802 0.177,0.167 10 false I3 1.104,2.823 1.521,2.979 0.417,0.156 10 false CA2H 2.219,2.813 2.635,2.969 0.417,0.156 10 false CA2L
*a Component with harness connector
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I3-35 (CA2H) - I3-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω Below 54 Ω: Short circuit between bus lines
70 Ω or higher: Open circuit in main bus lines
I3-35 (CA2H) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I3-34 (CA2L) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I3-35 (CA2H) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I3-34 (CA2L) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result Proceed to
OK A
NG (Open circuit in CAN main bus lines) B
NG (Short circuit between bus lines) C
·

NG (Ground short)

·

NG (+B short)


D



A

2.CHECK FOR DTC OUTPUT

B

3.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (POWER MANAGEMENT CONTROL ECU)

C

9.CHECK FOR SHORT IN SUB BUS 11 LINES (POWER MANAGEMENT CONTROL ECU)

D

16.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 6 JUNCTION CONNECTOR)
2.CHECK FOR DTC OUTPUT
a.

Reconnect the cable to the negative (-) auxiliary battery terminal.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG).


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > PM1 Gateway > Clear DTCs
50002 217

f.

Turn the power switch off.


g.

Turn the power switch on (IG).


h.

Check for DTCs.

Body Electrical > PM1 Gateway > Trouble Codes
50001 217

Result:
Result Proceed to
DTC U1002 is output from the power management control ECU (GTS display: PM1 Gateway) A
DTC U1002 is not output from the power management control ECU (GTS display: PM1 Gateway) B



A

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

3.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (POWER MANAGEMENT CONTROL ECU)
a.
C285701C26
1.365,0.104 1.771,0.344 0.406,0.24 1.948,1.979 2.083,1.979 2.083,1.979 2.208,1.49 true 2.354,1.479 2.583,1.969 2.583,1.969 2.75,1.969 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.521,0.135 1.979,0.333 0.458,0.198 10 false I3 2.823,1.885 3.427,2.094 0.604,0.208 10 false CA2H 1.573,1.896 2.188,2.104 0.615,0.208 10 false CA2L
*a Front view of wire harness connector
(to Power Management Control ECU)


Disconnect the I3 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-35 (CA2H) - I3-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

4.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 6 JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 6 JUNCTION CONNECTOR)
a.

Reconnect the I3 power management control ECU connector.


b.
C325243C01
0.448,1.667 0.896,1.896 0.448,0.229 2.292,1.635 2.74,1.865 0.448,0.229 0.813,2.208 1.104,2.208 true 2.531,2.208 2.76,2.208 true 0.781,2.365 0.979,2.563 0.979,2.563 1.115,2.563 true 2.5,2.375 2.667,2.583 2.667,2.583 2.802,2.583 true 2.385,2.427 2.583,2.906 2.583,2.906 2.719,2.906 true 0.656,2.427 0.875,2.823 0.875,2.823 1.01,2.823 true 0.375,2.083 0.51,2.083 0.51,2.083 0.563,2.302 true 2.083,2.094 2.219,2.094 2.219,2.094 2.271,2.313 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.542,1.688 0.854,1.885 0.313,0.198 10 false I178 2.365,1.667 2.677,1.865 0.313,0.198 10 false I180 0.208,2.01 0.521,2.208 0.313,0.198 10 false V 1.094,2.75 1.406,2.948 0.313,0.198 10 false LG 2.802,2.833 3.115,3.031 0.313,0.198 10 false LG 1.927,2.021 2.24,2.219 0.313,0.198 10 false R 1.177,2.125 1.802,2.323 0.625,0.198 10 false CANH*b 1.188,2.479 1.813,2.677 0.625,0.198 10 false CANL*b 2.833,2.135 3.375,2.385 0.542,0.25 10 false CANH*c 2.865,2.5 3.365,2.75 0.5,0.25 10 false CANL*c
*a Rear view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 2 Junction Connector
*c to CAN No. 5 Junction Connector


Disconnect the I178 and I180 CAN No. 6 junction connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
I178-1 (CANH) - I178-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 2 junction connector
I180-1 (CANH) - I180-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 5 junction connector



NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



Result:
Result Proceed to
OK A
NG (CAN No. 5 junction connector main bus lines) B
NG (CAN No. 2 junction connector main bus lines) C



A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

5.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 5 JUNCTION CONNECTOR)

C

6.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 2 JUNCTION CONNECTOR)
5.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 5 JUNCTION CONNECTOR)
a.

Reconnect the I178 and I180 CAN No. 6 junction connectors.


b.
C285287C56
1.5,0.427 1.906,0.698 0.406,0.271 1.427,2.042 0.969,1.448 0.969,1.448 0.854,1.448 true 0.927,2.708 1.031,2.708 1.031,2.708 1.427,2.354 true 1.625,2.031 2.25,0.979 2.25,0.979 2.385,0.979 true 2.052,2.76 1.875,2.76 1.875,2.76 1.635,2.354 true 1.594,0.49 2.052,0.688 0.458,0.198 10 false S16 0.323,1.365 0.979,1.615 0.656,0.25 10 false CANH*b 0.396,2.625 0.969,2.844 0.573,0.219 10 false CANL*b 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 2.448,0.896 3.115,1.188 0.667,0.292 10 false CANH*c 2.115,2.667 2.802,2.958 0.688,0.292 10 false CANL*c
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to CAN No. 6 Junction Connector
*c to Power Management Control ECU


Disconnect the S16 CAN No. 5 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
S16-2 (CANH) - S16-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 6 junction connector
S16-3 (CANH) - S16-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU



Result:
Result Proceed to
OK A
NG (CAN No. 6 junction connector main bus lines) B
NG (Power management control ECU main bus lines) C



A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - CAN NO. 5 JUNCTION CONNECTOR)

6.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 2 JUNCTION CONNECTOR)
a.

Reconnect the I178 and I180 CAN No. 6 junction connectors.


b.
C287058C72
1.479,0.396 1.958,0.719 0.479,0.323 1.813,2.688 1.99,2.688 1.99,2.688 1.99,2.052 true 2.573,2.677 2.417,2.677 2.417,2.677 2.417,2.042 true 1.979,1.719 1.979,0.865 1.979,0.865 1.698,0.865 true 2.406,1.729 2.406,0.844 2.406,0.844 2.594,0.844 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 1.615,0.469 2.042,0.677 0.427,0.208 10 false O30 1.135,0.802 2.052,1 0.917,0.198 10 false CANH*b 2.677,0.771 3.26,1.021 0.583,0.25 10 false CANH*c 1.26,2.615 2.177,2.813 0.917,0.198 10 false CANL*b 2.646,2.594 3.219,2.885 0.573,0.292 10 false CANL*c
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 3 Junction Connector
*c to CAN No. 6 Junction Connector


Disconnect the O30 CAN No. 2 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
O30-8 (CANH) - O30-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 3 junction connector
O30-11 (CANH) - O30-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 6 junction connector



Result:
Result Proceed to
OK A
NG (CAN No. 6 junction connector main bus lines) B
NG (CAN No. 3 junction connector main bus lines) C



A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

7.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 3 JUNCTION CONNECTOR)
7.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 3 JUNCTION CONNECTOR)
a.

Reconnect the O30 CAN No. 2 junction connector.


b.
C287058C73
1.479,0.396 1.958,0.719 0.479,0.323 0.813,2.688 0.99,2.688 0.99,2.688 0.99,2.052 true 1.427,2.677 1.271,2.677 1.271,2.677 1.271,2.042 true 0.99,1.719 0.99,0.865 0.99,0.865 0.76,0.865 true 1.271,1.729 1.271,0.844 1.271,0.844 1.458,0.844 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 1.604,0.469 2.031,0.677 0.427,0.208 10 false T15 0.198,0.802 1.115,1 0.917,0.198 10 false CANH*b 1.51,0.771 2.094,1.021 0.583,0.25 10 false CANH*c 0.271,2.615 1.188,2.813 0.917,0.198 10 false CANL*b 1.51,2.604 2.083,2.896 0.573,0.292 10 false CANL*c
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector
*c to CAN No. 2 Junction Connector


Disconnect the T15 CAN No. 3 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
T15-1 (CANH) - T15-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 4 junction connector
T15-3 (CANH) - T15-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 2 junction connector



Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main bus lines) B
NG (CAN No. 4 junction connector main bus lines) C



A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

8.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 4 JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN SUB BUS 11 MAIN LINES (CAN NO. 4 JUNCTION CONNECTOR)
a.

Reconnect the T15 CAN No. 3 junction connector.


b.
C183982C42
1.781,2.063 2.198,2.302 0.417,0.24 0.948,0.792 0.646,0.792 0.646,0.792 0.646,2.177 true 1.24,1.135 0.938,1.135 0.938,1.135 0.938,2.188 true 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 1,0.698 1.573,0.854 0.573,0.156 10 false CANH*b 1.292,1.042 1.854,1.198 0.563,0.156 10 false CANL*b 1.865,2.094 2.135,2.26 0.271,0.167 10 false T16
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to CAN No. 3 Junction Connector


Disconnect the T16 CAN No. 4 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T16-3 (CANH) - T16-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 3 JUNCTION CONNECTOR - CAN NO. 4 JUNCTION CONNECTOR)

9.CHECK FOR SHORT IN SUB BUS 11 LINES (POWER MANAGEMENT CONTROL ECU)
a.
C285701C26
1.365,0.104 1.771,0.344 0.406,0.24 1.948,1.979 2.083,1.979 2.083,1.979 2.208,1.49 true 2.354,1.479 2.583,1.969 2.583,1.969 2.75,1.969 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.521,0.135 1.979,0.333 0.458,0.198 10 false I3 2.823,1.885 3.427,2.094 0.604,0.208 10 false CA2H 1.573,1.896 2.188,2.104 0.615,0.208 10 false CA2L
*a Rear view of wire harness connector
(to Power Management Control ECU)


Disconnect the I3 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-35 (CA2H) - I3-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

10.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 6 JUNCTION CONNECTOR)
10.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 6 JUNCTION CONNECTOR)
a.

Reconnect the I3 power management control ECU connector.


b.

Disconnect the I178, I179 and I180 CAN No. 6 junction connectors.

C325244C01
2.188,1.25 2.594,1.49 0.406,0.24 3.635,1.313 4.042,1.552 0.406,0.24 4.75,1.302 5.156,1.542 0.406,0.24 2.406,1.781 2.635,1.781 true 3.802,1.802 4.031,1.802 true 4.958,1.802 5.188,1.802 true 1.938,1.646 2.063,1.646 2.063,1.646 2.188,1.875 true 3.354,1.521 3.479,1.521 3.479,1.521 3.604,1.875 true 4.448,1.552 4.573,1.552 4.573,1.552 4.76,1.875 true 4.958,1.938 5.094,2.167 5.094,2.167 5.208,2.167 true 3.792,1.938 3.927,2.167 3.927,2.167 4.042,2.167 true 2.396,1.927 2.531,2.156 2.531,2.156 2.646,2.156 true 2.292,1.958 2.49,2.438 2.49,2.438 2.604,2.438 true 3.677,1.979 3.875,2.458 3.875,2.458 3.99,2.458 true 4.833,1.979 5.031,2.458 5.031,2.458 5.146,2.458 true 0.115,0.083 0.427,0.281 0.313,0.198 10 false *a 2.26,1.292 2.573,1.49 0.313,0.198 10 false I178 3.708,1.354 4.021,1.552 0.313,0.198 10 false I179 4.833,1.354 5.146,1.552 0.313,0.198 10 false I180 1.771,1.583 1.958,1.813 0.188,0.229 10 false V 3.229,1.448 3.417,1.677 0.188,0.229 10 false L 4.292,1.458 4.479,1.688 0.188,0.229 10 false R 2.688,1.708 3.292,1.979 0.604,0.271 10 false CANH*b 4.073,1.719 4.677,1.99 0.604,0.271 10 false CANH*c 5.271,1.719 5.875,1.99 0.604,0.271 10 false CANH*d 2.729,2.073 3.333,2.344 0.604,0.271 10 false CANL*b 4.104,2.073 4.708,2.344 0.604,0.271 10 false CANL*c 5.292,2.083 5.896,2.354 0.604,0.271 10 false CANL*d 2.677,2.365 3.281,2.635 0.604,0.271 10 false LG 4.073,2.385 4.677,2.656 0.604,0.271 10 false LG 5.25,2.396 5.854,2.667 0.604,0.271 10 false LG
*a Rear view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 2 Junction Connector
*c to Driving Support ECU Assembly
(w/ Pre-crash Safety System)
*d to CAN No. 5 Junction Connector



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
I178-1 (CANH) - I178-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 2 junction connector
I179-1 (CANH) - I179-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Driving support ECU assembly*
I180-1 (CANH) - I180-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 5 junction connector


*: w/ Pre-crash Safety System



NOTICE:
·

Before disconnecting the connector, make a note of where it is connected.

·

Reconnect the connector to its original position.



Result:
Result Proceed to
OK A
NG (CAN No. 5 junction connector main bus lines) B
NG (CAN No. 2 junction connector main bus lines) C
NG (Driving support ECU assembly branch lines) D



A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

11.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 5 JUNCTION CONNECTOR)

C

12.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 2 JUNCTION CONNECTOR)

D

15.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
11.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 5 JUNCTION CONNECTOR)
a.

Reconnect the I178, I179 and I180 CAN No. 6 junction connectors.


b.
C285287C57
1.5,0.427 1.906,0.698 0.406,0.271 1.24,2.042 0.969,1.448 0.969,1.448 0.854,1.448 true 0.927,2.708 1.031,2.708 1.031,2.708 1.229,2.354 true 1.625,2.031 2.25,0.979 2.25,0.979 2.385,0.979 true 2.052,2.76 1.875,2.76 1.875,2.76 1.635,2.354 true 1.438,2.031 1.083,1.052 1.083,1.052 0.969,1.052 true 1.104,2.958 1.208,2.958 1.208,2.958 1.427,2.344 true 1.594,0.49 2.052,0.688 0.458,0.198 10 false S16 0.323,1.365 0.979,1.615 0.656,0.25 10 false CANH*b 0.396,2.625 0.969,2.844 0.573,0.219 10 false CANL*b 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 2.448,0.896 3.115,1.188 0.667,0.292 10 false CANH*d 2.115,2.667 2.802,2.958 0.688,0.292 10 false CANL*d 0.573,2.896 1.26,3.188 0.688,0.292 10 false CANL*c 0.417,0.979 1.083,1.271 0.667,0.292 10 false CANH*c
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Lane Departure Warning Camera
(w/ Lane Departure Alert System)
*c to CAN No. 6 Junction Connector
*d to Power Management Control ECU


Disconnect the S16 CAN No. 5 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
S16-1 (CANH) - S16-7 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Lane departure warning camera*
S16-2 (CANH) - S16-8 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 6 junction connector
S16-3 (CANH) - S16-9 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Power management control ECU


*: w/ Lane Departure Alert System



Result:
Result Proceed to
OK A
NG (CAN No. 6 junction connector main bus lines) B
NG (Power management control ECU main bus lines) C
NG (Lane departure warning camera branch lines) D



A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - CAN NO. 5 JUNCTION CONNECTOR)

D

15.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
12.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 2 JUNCTION CONNECTOR)
a.

Reconnect the I178, I179 and I180 CAN No. 6 junction connectors.


b.
C287058C74
1.479,0.396 1.958,0.719 0.479,0.323 1.813,2.688 1.99,2.688 1.99,2.688 1.99,2.052 true 2.573,2.677 2.417,2.677 2.417,2.677 2.417,2.042 true 1.979,1.719 1.979,0.865 1.979,0.865 1.698,0.865 true 2.406,1.729 2.406,0.844 2.406,0.844 2.594,0.844 true 2.125,1.729 2.125,0.563 2.125,0.563 2.313,0.563 true 2.281,2.948 2.125,2.948 2.125,2.948 2.125,2.031 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 1.583,0.469 2.01,0.677 0.427,0.208 10 false O30 1.135,0.802 2.052,1 0.917,0.198 10 false CANH*b 2.677,0.771 3.26,1.021 0.583,0.25 10 false CANH*d 1.26,2.615 2.177,2.813 0.917,0.198 10 false CANL*b 2.646,2.594 3.219,2.885 0.573,0.292 10 false CANL*d 2.406,0.49 2.99,0.74 0.583,0.25 10 false CANH*c 2.375,2.875 2.948,3.167 0.573,0.292 10 false CANL*c
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 3 Junction Connector
*c to Blind Spot Monitor Sensor RH
(w/ Blind Spot Monitor System)
*d to CAN No. 6 Junction Connector


Disconnect the O30 CAN No. 2 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
O30-8 (CANH) - O30-19 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 3 junction connector
O30-9 (CANH) - O30-20 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Blind spot monitor sensor RH*
O30-11 (CANH) - O30-22 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 6 junction connector


*: w/ Blind Spot Monitor System



Result:
Result Proceed to
OK A
NG (CAN No. 6 junction connector main bus lines) B
NG (CAN No. 3 junction connector main bus lines) C
NG (Blind spot monitor sensor RH branch lines) D



A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

13.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 3 JUNCTION CONNECTOR)

D

15.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
13.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 3 JUNCTION CONNECTOR)
a.

Reconnect the O30 CAN No. 2 junction connector.


b.
C287058C75
1.479,0.396 1.958,0.719 0.479,0.323 0.813,2.688 0.99,2.688 0.99,2.688 0.99,2.052 true 1.427,2.677 1.271,2.677 1.271,2.677 1.271,2.042 true 0.99,1.719 0.99,0.865 0.99,0.865 0.708,0.865 true 1.271,1.729 1.271,0.844 1.271,0.844 1.458,0.844 true 1.125,1.729 1.125,0.563 1.125,0.563 0.917,0.563 true 0.958,2.948 1.135,2.948 1.135,2.948 1.135,2.031 true 0.063,0.042 0.375,0.24 0.313,0.198 10 false *a 1.583,0.469 2.01,0.677 0.427,0.208 10 false T15 0.167,0.802 1.083,1 0.917,0.198 10 false CANH*b 1.521,0.771 2.104,1.021 0.583,0.25 10 false CANH*d 0.292,2.615 1.208,2.813 0.917,0.198 10 false CANL*b 1.49,2.594 2.063,2.885 0.573,0.292 10 false CANL*d 0.365,0.479 0.948,0.729 0.583,0.25 10 false CANH*c 0.427,2.875 1,3.167 0.573,0.292 10 false CANL*c
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector
*c to Rear Television Camera Assembly
(w/ Parking Assist Monitor System without Parallel Parking Assist Function)
*d to CAN No. 2 Junction Connector


Disconnect the T15 CAN No. 3 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
T15-1 (CANH) - T15-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 4 junction connector
T15-2 (CANH) - T15-13 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Rear television camera assembly*
T15-3 (CANH) - T15-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN No. 2 junction connector


*: w/ Parking Assist Monitor System without Parallel Parking Assist Function



Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main bus lines) B
NG (CAN No. 4 junction connector main bus lines) C
NG (Rear television camera assembly branch lines) D



A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

14.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 4 JUNCTION CONNECTOR)

D

15.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
14.CHECK FOR SHORT IN SUB BUS 11 LINES (CAN NO. 4 JUNCTION CONNECTOR)
a.

Reconnect the T15 CAN No. 3 junction connector.


b.
C183982C42
1.781,2.063 2.198,2.302 0.417,0.24 0.948,0.792 0.646,0.792 0.646,0.792 0.646,2.177 true 1.24,1.135 0.938,1.135 0.938,1.135 0.938,2.188 true 0.177,0.115 0.333,0.292 0.156,0.177 10 false *a 1,0.698 1.573,0.854 0.573,0.156 10 false CANH*b 1.292,1.042 1.854,1.198 0.563,0.156 10 false CANL*b 1.865,2.094 2.135,2.26 0.271,0.167 10 false T16
*a Rear view of wire harness connector
(to CAN No. 4 Junction Connector)
*b to CAN No. 3 Junction Connector


Disconnect the T16 CAN No. 4 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
T16-3 (CANH) - T16-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (CAN NO. 3 JUNCTION CONNECTOR - CAN NO. 4 JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN SUB BUS 11 LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short-circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
A261175C46
1.813,0.583 2.313,0.875 0.5,0.292 1.531,2.917 1.625,2.917 1.625,2.917 1.813,1.906 true 2.167,2.906 2.083,2.906 2.083,2.906 1.865,1.906 true 0.063,0.021 0.271,0.24 0.208,0.219 10 false *a 1.99,0.635 2.167,0.802 0.177,0.167 10 false I3 1.104,2.823 1.521,2.979 0.417,0.156 10 false CA2H 2.219,2.813 2.635,2.969 0.417,0.156 10 false CA2L
*a Component with harness connected
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I3-35 (CA2H) - I3-34 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω


HINT:

If the resistance changes to normal when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR

16.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 6 JUNCTION CONNECTOR)
a.

Disconnect the I178, I179 and I180 CAN No. 6 junction connectors.

C325245C01
5.479,0.25 5.792,0.458 0.313,0.208 3.313,1.24 3.698,1.438 0.385,0.198 2.344,1.24 2.698,1.458 0.354,0.219 0.885,1.229 1.26,1.438 0.375,0.208 5.198,0.521 5.396,0.521 5.396,0.521 5.615,1.063 true 6.135,2.146 6.333,2.146 6.333,2.146 6.333,1.615 true 2.458,1.708 2.635,1.708 true 1.073,1.698 1.25,1.698 true 3.51,1.719 3.688,1.719 true 1.073,1.844 1.167,2.094 1.167,2.094 1.281,2.094 true 2.438,1.854 2.531,2.104 2.531,2.104 2.646,2.104 true 3.5,1.865 3.594,2.115 3.594,2.115 3.708,2.115 true 0.979,1.875 1.115,2.365 1.115,2.365 1.229,2.365 true 2.333,1.885 2.469,2.375 2.469,2.375 2.583,2.375 true 3.396,1.896 3.531,2.385 3.531,2.385 3.646,2.385 true 3.063,1.479 3.208,1.479 3.208,1.479 3.323,1.792 true 2,1.469 2.146,1.469 2.146,1.469 2.26,1.781 true 0.635,1.458 0.781,1.458 0.781,1.458 0.896,1.771 true 0.875,0.198 1.188,0.396 0.313,0.198 10 false *a 4.208,0.365 4.521,0.563 0.313,0.198 10 false *1 4.938,0.438 5.24,0.677 0.302,0.24 10 false CG 5.552,0.271 5.854,0.51 0.302,0.24 10 false I39 5.771,2.073 6.073,2.313 0.302,0.24 10 false BAT 0.938,1.25 1.24,1.49 0.302,0.24 10 false I178 2.385,1.271 2.688,1.51 0.302,0.24 10 false I179 3.375,1.26 3.677,1.5 0.302,0.24 10 false I180 1.313,1.615 1.885,1.885 0.573,0.271 10 false CANH*b 2.677,1.625 3.25,1.896 0.573,0.271 10 false CANH*c 3.75,1.635 4.323,1.906 0.573,0.271 10 false CANH*d 1.344,2.01 1.917,2.281 0.573,0.271 10 false CANL*b 2.708,2.021 3.281,2.292 0.573,0.271 10 false CANL*c 3.792,2.031 4.365,2.302 0.573,0.271 10 false CANL*d 0.479,1.375 0.781,1.615 0.302,0.24 10 false V 1.854,1.396 2.156,1.635 0.302,0.24 10 false L 1.313,2.281 1.615,2.521 0.302,0.24 10 false LG 2.656,2.302 2.958,2.542 0.302,0.24 10 false LG 3.729,2.313 4.031,2.552 0.302,0.24 10 false LG 2.906,1.406 3.208,1.646 0.302,0.24 10 false R
*1 DLC3 - -
*a Rear view of wire harness connector
(to CAN No. 6 Junction Connector)
*b to CAN No. 2 Junction Connector
*c to Driving Support ECU Assembly
(w/ Pre-crash Safety System)
*d to CAN No. 5 Junction Connector



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
I178-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 2 junction connector
I178-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I179-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Driving support ECU assembly*
I179-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I180-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 5 junction connector
I180-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I178-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 2 junction connector
I178-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
I179-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Driving support ECU assembly*
I179-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
I180-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 5 junction connector
I180-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


*: w/ Pre-crash Safety System


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




Result:
Result Proceed to
OK A
NG (CAN No. 5 junction connector main bus line) B
NG (CAN No. 2 junction connector main bus line) C
NG (Driving support ECU assembly branch line) D



A

REPLACE CAN NO. 6 JUNCTION CONNECTOR

B

17.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 5 JUNCTION CONNECTOR)

C

19.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 2 JUNCTION CONNECTOR)

D

22.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
17.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 5 JUNCTION CONNECTOR)
a.

Reconnect the I178, I179 and I180 CAN No. 6 junction connectors.


b.

Disconnect the S16 CAN No. 5 junction connector.

C287170C14
5.406,0.26 5.823,0.552 0.417,0.292 1.958,0.25 2.344,0.552 0.385,0.302 5.51,1.229 5.99,0.75 5.99,0.75 6.156,0.75 true 5.635,2.25 5.792,2.25 5.792,2.25 6.229,1.802 true 1.333,2.125 1.448,2.125 1.448,2.125 1.781,1.938 true 1.344,1.51 1.479,1.51 1.479,1.51 1.781,1.688 true 1.469,2.427 1.583,2.427 1.583,2.427 1.948,1.927 true 1.948,1.698 1.552,1.052 1.552,1.052 1.448,1.052 true 2.104,1.688 2.823,1.104 2.823,1.104 2.969,1.104 true 2.104,1.927 2.771,2.5 2.771,2.5 2.938,2.5 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 4.021,0.094 4.333,0.292 0.313,0.198 10 false *1 5.531,0.302 5.844,0.5 0.313,0.198 10 false I39 6.208,0.667 6.521,0.865 0.313,0.198 10 false CG 5.344,2.156 5.802,2.354 0.458,0.198 10 false BAT 2.031,0.313 2.49,0.51 0.458,0.198 10 false S16 0.792,1.417 1.708,1.615 0.917,0.198 10 false CANH*b 0.802,2.031 1.719,2.229 0.917,0.198 10 false CANL*b 0.917,0.958 1.833,1.156 0.917,0.198 10 false CANH*c 0.958,2.333 1.875,2.531 0.917,0.198 10 false CANL*c 3.01,1.021 3.927,1.219 0.917,0.198 10 false CANH*d 2.979,2.406 3.896,2.604 0.917,0.198 10 false CANL*d
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 5 Junction Connector)
*b to Lane Departure Warning Camera
(w/ Lane Departure Alert System)
*c to CAN No. 6 Junction Connector *d to Power Management Control ECU



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
S16-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Lane departure warning camera*
S16-7 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
S16-2 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 6 junction connector
S16-8 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
S16-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Power management control ECU
S16-9 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
S16-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Lane departure warning camera*
S16-7 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
S16-2 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 6 junction connector
S16-8 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
S16-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Power management control ECU
S16-9 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


*: w/ Lane Departure Alert System


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




Result:
Result Proceed to
OK A
NG (CAN No. 6 junction connector main bus line) B
NG (Power management control ECU main bus line) C
NG (Lane departure warning camera branch line) D



A

REPLACE CAN NO. 5 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

18.CHECK FOR SHORT IN SUB BUS 11 LINE (POWER MANAGEMENT CONTROL ECU)

D

22.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
18.CHECK FOR SHORT IN SUB BUS 11 LINE (POWER MANAGEMENT CONTROL ECU)
a.

Reconnect the S16 CAN No. 5 junction connector.


b.
C285701C27
1.365,0.104 1.771,0.344 0.406,0.24 1.948,1.979 2.083,1.979 2.083,1.979 2.208,1.49 true 2.354,1.49 2.583,1.979 2.583,1.979 2.75,1.979 true 2.375,0.875 2.76,0.698 true 0.677,0.698 1.104,0.875 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.51,0.135 1.938,0.333 0.427,0.198 10 false I3 2.823,1.885 3.427,2.094 0.604,0.208 10 false CA2H 1.573,1.896 2.188,2.104 0.615,0.208 10 false CA2L 2.823,0.573 3.146,0.792 0.323,0.219 10 false E1 0.26,0.594 0.885,0.885 0.625,0.292 10 false AM22
*a Front view of wire harness connector
(to Power Management Control ECU)


Disconnect the I3 power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I3-35 (CA2H) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I3-34 (CA2L) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I3-35 (CA2H) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I3-34 (CA2L) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result
OK
NG


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 5 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

19.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 2 JUNCTION CONNECTOR)
a.

Reconnect the I178, I179 and I180 CAN No. 6 junction connectors.


b.

Disconnect the O30 CAN No. 2 junction connector.

C325210C01
2.031,0.135 2.417,0.396 0.385,0.26 5.635,0.177 6.021,0.438 0.385,0.26 2.604,1.51 2.938,0.677 2.938,0.677 3.073,0.677 true 2.833,1.51 3.073,0.896 3.073,0.896 3.208,0.896 true 2.594,1.75 3.021,2.458 3.021,2.458 3.135,2.458 true 2.823,1.75 3.125,2.198 3.125,2.198 3.24,2.198 true 2.49,1.75 2.302,2.427 2.302,2.427 2.146,2.427 true 2.49,1.51 2.292,0.719 2.292,0.719 2.167,0.719 true 5.792,1.219 6.104,0.74 6.104,0.74 6.24,0.74 true 6.479,1.813 6.198,2.229 6.198,2.229 6.042,2.229 true 1.594,0.635 2.51,0.833 0.917,0.198 10 false CANH*b 3.146,0.594 4.063,0.792 0.917,0.198 10 false CANH*c 3.292,0.823 4.208,1.021 0.917,0.198 10 false CANH*d 3.302,2.125 4.219,2.323 0.917,0.198 10 false CANL*d 3.208,2.375 4.125,2.573 0.917,0.198 10 false CANL*c 1.573,2.344 2.49,2.542 0.917,0.198 10 false CANL*b 0.104,0.063 1.021,0.26 0.917,0.198 10 false *a 2.094,0.188 3.01,0.385 0.917,0.198 10 false O30 5.729,0.229 6.646,0.427 0.917,0.198 10 false I39 4.344,0.167 5.26,0.365 0.917,0.198 10 false *1 6.333,0.667 6.927,0.896 0.594,0.229 10 false CG 5.708,2.156 6.625,2.354 0.917,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 2 Junction Connector)
*b to CAN No. 3 Junction Connector
*c to Blind Spot Monitor Sensor RH
(w/ Blind Spot Monitor System)
*d to CAN No. 6 Junction Connector



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
O30-8 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 3 junction connector
O30-19 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
O30-9 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Blind spot monitor sensor RH*
O30-20 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
O30-11 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 6 junction connector
O30-22 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
O30-8 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 3 junction connector
O30-19 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
O30-9 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Blind spot monitor sensor RH*
O30-20 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
O30-11 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 6 junction connector
O30-22 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


*: w/ Blind Spot Monitor System


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




Result:
Result Proceed to
OK A
NG (CAN No. 6 junction connector main bus line) B
NG (CAN No. 3 junction connector main bus line) C
NG (Blind spot monitor sensor RH branch line) D



A

REPLACE CAN NO. 2 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 6 JUNCTION CONNECTOR)

C

20.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 3 JUNCTION CONNECTOR)

D

22.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
20.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 3 JUNCTION CONNECTOR)
a.

Reconnect the O30 CAN No. 2 junction connector.


b.

Disconnect the T15 CAN No. 3 junction connector.

C325210C03
2.031,0.135 2.417,0.396 0.385,0.26 5.635,0.177 6.021,0.438 0.385,0.26 1.792,1.51 2.125,0.677 2.125,0.677 2.26,0.677 true 1.917,1.51 2.156,0.896 2.156,0.896 2.292,0.896 true 1.792,1.75 2.219,2.458 2.219,2.458 2.333,2.458 true 1.906,1.75 2.208,2.198 2.208,2.198 2.323,2.198 true 1.677,1.75 1.49,2.427 1.49,2.427 1.333,2.427 true 1.667,1.51 1.469,0.719 1.469,0.719 1.344,0.719 true 5.792,1.219 6.104,0.74 6.104,0.74 6.24,0.74 true 6.479,1.813 6.198,2.229 6.198,2.229 6.042,2.229 true 0.781,0.635 1.698,0.833 0.917,0.198 10 false CANH*b 2.323,0.594 3.24,0.792 0.917,0.198 10 false CANH*c 2.365,0.823 3.281,1.021 0.917,0.198 10 false CANH*d 2.396,2.125 3.313,2.323 0.917,0.198 10 false CANL*d 2.406,2.375 3.323,2.573 0.917,0.198 10 false CANL*c 0.771,2.344 1.688,2.542 0.917,0.198 10 false CANL*b 0.104,0.063 1.021,0.26 0.917,0.198 10 false *a 2.094,0.188 3.01,0.385 0.917,0.198 10 false T15 5.729,0.229 6.646,0.427 0.917,0.198 10 false I39 4.344,0.167 5.26,0.365 0.917,0.198 10 false *1 6.333,0.667 6.927,0.896 0.594,0.229 10 false CG 5.708,2.156 6.625,2.354 0.917,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to CAN No. 3 Junction Connector)
*b to CAN No. 4 Junction Connector
*c to Rear Television Camera Assembly
(w/ Parking Assist Monitor System without Parallel Parking Assist Function)
*d to CAN No. 2 Junction Connector



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result Connected to
T15-1 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 4 junction connector
T15-12 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T15-2 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short Rear television camera assembly*
T15-13 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T15-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short CAN No. 2 junction connector
T15-14 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T15-1 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 4 junction connector
T15-12 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
T15-2 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short Rear television camera assembly*
T15-13 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short
T15-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short CAN No. 2 junction connector
T15-14 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


*: w/ Parking Assist Monitor System without Parallel Parking Assist Function


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




Result:
Result Proceed to
OK A
NG (CAN No. 2 junction connector main bus line) B
NG (CAN No. 4 junction connector main bus line) C
NG (Rear television camera assembly branch line) D



A

REPLACE CAN NO. 3 JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 2 JUNCTION CONNECTOR - CAN NO. 3 JUNCTION CONNECTOR)

C

21.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 4 JUNCTION CONNECTOR)

D

22.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
21.CHECK FOR SHORT IN SUB BUS 11 LINE (CAN NO. 4 JUNCTION CONNECTOR)
a.

Reconnect the T15 CAN No. 3 junction connector.


b.
C287171C29
1.5,0.26 1.938,0.573 0.438,0.313 1.521,2.635 1.958,2.927 0.438,0.292 1.625,3.542 2.104,3.094 2.104,3.094 2.281,3.094 true 1.771,4.479 1.917,4.479 1.917,4.479 2.323,4.094 true 1.115,2.26 1.26,2.26 1.26,2.26 1.781,1.563 true 2.552,2.24 2.385,2.24 2.385,2.24 2.021,1.573 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.156,2.51 0.469,2.708 0.313,0.198 10 false *1 1.583,0.313 2.198,0.51 0.615,0.198 10 false T16 1.656,2.688 1.969,2.885 0.313,0.198 10 false I39 2.344,3 2.656,3.198 0.313,0.198 10 false CG 1.469,4.385 1.927,4.583 0.458,0.198 10 false BAT 0.719,2.177 1.333,2.375 0.615,0.198 10 false CANL 2.604,2.135 3.219,2.333 0.615,0.198 10 false CANH
*1 DLC3
*a Front view of wire harness connector
(to CAN No. 4 Junction Connector)


Disconnect the T16 CAN No. 4 junction terminal connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
T16-3 (CANH) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
T16-2 (CANL) - I39-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
T16-3 (CANH) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
T16-2 (CANL) - I39-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.




Result:
Result
OK
NG



OK

REPLACE CAN NO. 4 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN NO. 3 JUNCTION CONNECTOR - CAN NO. 4 JUNCTION CONNECTOR)

22.CHECK FOR SHORT IN SUB BUS 11 LINE (ECU, SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B or shorted to GND is connected.


c.
A261175C45
1.813,0.583 2.313,0.875 0.5,0.292 1.604,1.083 1.698,1.083 1.698,1.083 1.823,1.688 true 2.552,1.083 2.448,1.083 2.448,1.083 2.229,1.688 true 1.531,2.917 1.625,2.917 1.625,2.917 1.813,1.906 true 2.167,2.906 2.083,2.906 2.083,2.906 1.865,1.906 true 0.063,0.021 0.271,0.24 0.208,0.219 10 false *a 2.573,1 2.99,1.156 0.417,0.156 10 false AM22 1.375,1 1.573,1.156 0.198,0.156 10 false E1 1.99,0.635 2.167,0.802 0.177,0.167 10 false I3 1.104,2.823 1.521,2.979 0.417,0.156 10 false CA2H 2.219,2.813 2.635,2.969 0.417,0.156 10 false CA2L
*a Component with harness connected
(Power Management Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Result
I3-35 (CA2H) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANH ground short
I3-34 (CA2L) - I3-6 (E1) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher Below 200 Ω: CANL ground short
I3-35 (CA2H) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANH +B short
I3-34 (CA2L) - I3-1 (AM22) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher Below 6 kΩ: CANL +B short



Result:
Result
OK
NG


HINT:
·

It is only necessary to perform the inspection in the above table for the result (short circuit) that was obtained in the Check Sub Bus 11 inspection.

·

Find the necessary inspection from the Result column that matches the result in the Result column from the Check Sub Bus 11 inspection.

·

If the resistance changes to normal when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINE OR CONNECTOR