Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM S

NETWORKING  CAN COMMUNICATION SYSTEM  DIAGNOSTIC TROUBLE CODE CHART  


DIAGNOSTIC TROUBLE CODE CHART
DTC No. Detection Item Trouble Area Note Link
U0100 Lost Communication with ECM / PCM "A"
·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of power management control ECU

·

Power management control ECU

·

Power source circuit of ECM

·

ECM

·

Open or short in CAN No. 1 junction connector


As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs. Click here
U0104 Lost Communication with Driving Support ECU
·

Driving support ECU assembly branch line or connector

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Driving support ECU assembly


The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11. Click here
U0129 Lost Communication with Brake System Control Module
·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of power management control ECU

·

Power management control ECU

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU)

·

Open or short in CAN No. 1 junction connector


As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs. Click here
U0129 Lost Communication with Brake System Control Module
·

Brake booster with master cylinder assembly (skid control ECU) branch line or connector

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU) ground circuit

·

Brake booster with master cylinder assembly (skid control ECU)


As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs. Click here
U0199 Lost Communication with "Door Control Module A"
·

Outer mirror control ECU assembly (for driver side) branch line or connector

·

Power source circuit of outer mirror control ECU assembly (for driver side)

·

Outer mirror control ECU assembly (for driver side) ground circuit

·

Outer mirror control ECU assembly (for driver side)


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1. Click here
U0200 Lost Communication with "Door Control Module B"
·

Outer mirror control ECU assembly (for front passenger side) branch line or connector

·

Power source circuit of outer mirror control ECU assembly (for front passenger side)

·

Outer mirror control ECU assembly (for front passenger side) ground circuit

·

Outer mirror control ECU assembly (for front passenger side)


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1. Click here
U0208 Lost Communication with "Seat Control Module A"
·

Position control ECU and switch assembly (for driver side) branch line or connector

·

Power source circuit of position control ECU and switch assembly (for driver side)

·

Position control ECU and switch assembly (for driver side) ground circuit

·

Position control ECU and switch assembly (for driver side)


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1. Click here
U0233 Lost Communication with Blind Spot Monitor Master Module
·

Blind spot monitor sensor RH branch line or connector

·

Power source circuit of blind spot monitor sensor RH

·

Blind spot monitor sensor RH ground circuit

·

Blind spot monitor sensor RH


The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11. Click here
U0235 Lost Communication with Cruise Control Front Distance Range Sensor
·

Open or short in sub bus 13 main line or connector

·

Millimeter wave radar sensor assembly

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit


The driving support ECU assembly stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 13. Click here
U023A Lost Communication with Front Camera Module
·

Lane departure warning camera branch line or connector

·

Power source circuit of lane departure warning camera

·

Lane departure warning camera ground circuit

·

Lane departure warning camera


The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11. Click here
U0265 Lost Communication with Parking Assist Monitor Module
·

Rear television camera assembly branch line or connector

·

Power source circuit of rear television camera assembly

·

Rear television camera assembly ground circuit

·

Rear television camera assembly


The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11. Click here
U0293 Lost Communication with HV ECU
·

Open or short in sub bus 15 main line or connector

·

Open or short in sub bus 15 branch line or connector

·

Power source circuit of ECM

·

ECM

·

Power source circuit of power management control ECU

·

Power management control ECU

·

Power source circuit of brake booster with master cylinder assembly (skid control ECU)

·

Brake booster with master cylinder assembly (skid control ECU)

·

Open or short in CAN No. 1 junction connector


As there is no sub bus monitor ECU for sub bus 15, each ECU detects communication stops and stores DTCs. Click here
U1002 Lost Communication with Gateway Module (Main Body ECU)
·

Open or short in sub bus 1 main line or connector

·

Open or short in sub bus 1 branch line or connector

·

Main body ECU (Multiplex network body ECU)

·

Outer mirror control ECU assembly (for Driver side)

·

Outer mirror control ECU assembly (for Front passenger side)

·

Position control ECU and switch assembly (for Driver side)

·

Open or short in CAN junction LH2 connector

·

Open or short in CAN junction RH2 connector


The main body ECU (multiplex network body ECU) stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 1. Click here
U1002 Lost Communication with Gateway Module
·

Open or short in sub bus 11 main lines or connector

·

Short in sub bus 11 branch lines or connector

·

Power management control ECU

·

Lane departure warning camera

(w/ Lane Departure Alert System)

·

Driving support ECU assembly

(w/ Pre-crash Safety System)

·

Blind spot monitor sensor RH

(w/ Blind Spot Monitor System)

·

Rear television camera assembly

(w/ Parking Assist Monitor System without Parallel Parking Assist Function)

·

Open or short in CAN No. 2 junction connector

·

Open or short in CAN No. 3 junction connector

·

Open or short in CAN No. 4 junction connector

·

Open or short in CAN No. 5 junction connector

·

Open or short in CAN No. 6 junction connector


The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11. Click here
U1002 Lost Communication with Gateway Module (Sensor Bus)
·

Open or short in sub bus 13 main line or connector

·

Driving support ECU assembly

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Millimeter wave radar sensor assembly

·

Power source circuit of millimeter wave radar sensor assembly

·

Millimeter wave radar sensor assembly ground circuit


The driving support ECU assembly stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 13. Click here