Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Open in CAN Main Bus Line  


DESCRIPTION

There may be an open circuit in one of the V bus main lines and/or a DLC3 branch line when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
·

DLC3 branch line or connector

·

CAN main bus line or connector

·

ECM

·

Combination meter assembly

·

CAN junction LH1 connector

·

CAN junction RH1 connector



This malfunction is not related to the lines of a CAN main bus branch or to ECUs or sensors connected a CAN main bus branch.

WIRING DIAGRAM

C318610E05
0.177,0.104 1.156,0.448 0.979,0.344 12 false V Bus: 0.302,0.875 0.719,1.156 0.417,0.281 10 false I18 0.552,0.875 2.427,1.167 1.875,0.292 10 false Combination Meter Assembly 5.323,0.417 6.906,0.781 1.583,0.365 10 false x: Suspected Area 3.156,0.667 3.76,0.917 0.604,0.25 10 false 120 Ω 2.51,1.271 2.948,1.583 0.438,0.313 10 false CANL 3.823,1.26 4.26,1.573 0.438,0.313 10 false CANH 2.75,1.469 2.969,1.688 0.219,0.219 10 false 16 3.792,1.458 4.01,1.677 0.219,0.219 10 false 17 5.156,2.542 5.375,2.76 0.219,0.219 10 false 6 2.677,1.76 2.896,1.979 0.219,0.219 10 false W 2.875,2.094 3.094,2.313 0.219,0.219 10 false I94 3.635,2.083 3.854,2.302 0.219,0.219 10 false I94 3.958,2.083 4.177,2.302 0.219,0.219 10 false 1 2.656,2.094 2.844,2.292 0.188,0.198 10 false 2 0.542,2.698 2.354,2.979 1.813,0.281 10 false CAN Junction RH1 Connector 4.323,2.708 4.542,2.927 0.219,0.219 10 false I96 4.323,2.958 4.542,3.177 0.219,0.219 10 false I96 4.365,2.51 4.583,2.74 0.219,0.229 10 false 1 4.375,3.177 4.563,3.375 0.188,0.198 10 false 2 5.26,3.083 5.479,3.302 0.219,0.219 10 false 14 5.021,2.542 5.24,2.76 0.219,0.219 10 false G 5,3.167 5.219,3.385 0.219,0.219 10 false W 5.375,2.698 5.885,2.917 0.51,0.219 10 false CANH 5.51,2.958 6.021,3.177 0.51,0.219 10 false CANL 5.688,3.281 5.906,3.5 0.219,0.219 10 false I39 5.927,3.281 6.385,3.51 0.458,0.229 10 false DLC3 2.833,3.479 3.156,3.698 0.323,0.219 10 false I101 3.635,4.24 3.948,4.479 0.313,0.24 10 false I93 3.958,3.479 4.177,3.708 0.219,0.229 10 false 1 2.646,3.49 2.833,3.688 0.188,0.198 10 false 2 3.854,1.771 4.073,1.99 0.219,0.219 10 false R 3.833,3.854 4.052,4.073 0.219,0.219 10 false B 2.719,3.865 2.938,4.083 0.219,0.219 10 false W 2.875,4.24 3.188,4.479 0.313,0.24 10 false I93 3.594,3.479 3.958,3.708 0.365,0.229 10 false I101 3.99,4.24 4.208,4.469 0.219,0.229 10 false 1 2.646,4.25 2.833,4.448 0.188,0.198 10 false 2 3.979,5.646 4.198,5.875 0.219,0.229 10 false 1 2.625,5.635 2.813,5.833 0.188,0.198 10 false 2 0.583,4.885 2.396,5.167 1.813,0.281 10 false CAN Junction LH1 Connector 2.844,5.635 3.156,5.875 0.313,0.24 10 false I104 3.583,5.635 3.896,5.875 0.313,0.24 10 false I104 2.677,5.938 2.896,6.156 0.219,0.219 10 false W 2.719,6.604 2.938,6.823 0.219,0.219 10 false W 3.896,5.938 4.115,6.156 0.219,0.219 10 false G 3.844,6.604 4.063,6.823 0.219,0.219 10 false B 2.771,6.792 2.99,7.01 0.219,0.219 10 false 26 3.781,6.792 4,7.01 0.219,0.219 10 false 13 3.781,6.99 4.292,7.208 0.51,0.219 10 false CANH 2.552,6.99 3.063,7.208 0.51,0.219 10 false CANL 3.156,7.594 3.667,7.813 0.51,0.219 10 false 120 Ω 4.365,7.281 4.719,7.521 0.354,0.24 10 false A25 4.667,7.281 5.021,7.521 0.354,0.24 10 false ECM 0.802,8.021 2.615,8.302 1.813,0.281 10 false : CAN Main Bus Line (CANH) 0.833,8.406 2.646,8.688 1.813,0.281 10 false : CAN Main Bus Line (CANL) 4.156,8.01 5.969,8.292 1.813,0.281 10 false : CAN Branch Line (CANH) 4.177,8.375 5.99,8.656 1.813,0.281 10 false : CAN Branch Line (CANL)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), wait at least 60 seconds and then drive the vehicle at a speed of 36 km/h (22 mph) or more for at least 7 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

·

Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wire harnesses, and to make future maintenance easier.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (DLC3 BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C210421C91
1.51,0.698 1.948,1 0.438,0.302 2.063,1.865 2.208,1.313 2.208,1.313 2.427,1.313 true 2.073,2.573 2.198,2.948 2.198,2.948 2.354,2.948 true 0.115,0.156 0.958,0.49 0.844,0.333 10 false *1 1.625,0.76 2.156,1.021 0.531,0.26 10 false I39 2.49,1.24 3.094,1.531 0.604,0.292 10 false CANH 2.406,2.865 3.146,3.115 0.74,0.25 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I39-6 (CANH) - I39-14 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω


NOTICE:

When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Result
OK
NG



OK

2.CHECK FOR OPEN IN CAN BUS LINES (ECM)

NG

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR OPEN IN CAN BUS LINES (ECM)
a.
C239823C38
0.156,1.521 0.49,1.781 0.333,0.26 2.573,1.531 2.573,0.667 2.573,0.667 2.365,0.667 true 2.573,1.625 2.938,1.625 2.938,1.625 2.938,2.406 true 0.188,0.229 0.552,0.573 0.365,0.344 10 false *a 1.896,0.594 2.479,0.865 0.583,0.271 10 false CANH 2.771,2.438 3.292,2.688 0.521,0.25 10 false CANL 0.198,1.563 0.521,1.729 0.323,0.167 10 false A25
*a Front view of wire harness connector
(to ECM)


Disconnect the A25 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-13 (CANH) -A25-26 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

3.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY)
3.CHECK FOR OPEN IN CAN BUS LINES (COMBINATION METER ASSEMBLY)
a.

Reconnect the A25 ECM connector.


b.
E224284C91
1.24,0.521 1.729,0.813 0.49,0.292 1.479,2.156 1.479,2.5 1.479,2.5 1.667,2.5 true 1.365,2.156 1.365,2.51 1.365,2.51 1.177,2.51 true 0.156,0.177 0.438,0.458 0.281,0.281 10 false *a 1.75,2.417 2.281,2.656 0.531,0.24 10 false CANH 0.771,2.417 1.302,2.656 0.531,0.24 10 false CANL 1.375,0.594 1.656,0.771 0.281,0.177 10 false I18
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the I18 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-17 (CANH) - I18-16 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK FOR OPEN IN CAN BUS LINES (CAN JUNCTION RH1 CONNECTOR)
4.CHECK FOR OPEN IN CAN BUS LINES (CAN JUNCTION RH1 CONNECTOR)
a.

Reconnect the I18 combination meter assembly connector.


b.
C252873C05
1.281,1.656 1.625,1.896 0.344,0.24 2.531,1.583 2.906,1.833 0.375,0.25 2.771,2.375 3.104,2.375 3.104,2.375 3.104,2.604 true 2.635,2.396 2.781,3.104 2.781,3.104 2.917,3.104 true 2.781,2.24 3.354,1.375 3.354,1.375 3.042,1.375 true 2.552,2.302 2.448,2.094 2.448,2.094 2.271,2.094 true 1.406,2.188 1.063,1.969 1.063,1.969 0.844,1.969 true 1.229,2.323 0.948,2.323 true 1.49,2.365 1.771,2.365 true 1.344,2.385 1.5,2.635 1.5,2.635 1.5,2.844 true 0.281,1.875 1,2.135 0.719,0.26 10 false CANH*b 2.49,1.281 3.188,1.563 0.698,0.281 10 false CANH*c 1.823,2.271 2.469,2.5 0.646,0.229 10 false CANL*b 2.802,2.635 3.385,2.885 0.583,0.25 10 false CANL*c 0.802,2.24 1.01,2.531 0.208,0.292 10 false R 1.438,2.875 1.698,3.156 0.26,0.281 10 false W 2.115,2 2.344,2.26 0.229,0.26 10 false B 3,3.021 3.313,3.24 0.313,0.219 10 false W 0.115,0.125 0.438,0.427 0.323,0.302 10 false *a 1.354,1.698 1.677,1.948 0.323,0.25 10 false I94 2.583,1.625 2.875,1.854 0.292,0.229 10 false I101
*a Rear view of wire harness connector
(to CAN Junction RH1 Connector)
*b to Combination Meter Assembly
*c to CAN Junction LH1 Connector


Disconnect the I94 and I101 CAN junction RH1 connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
I101-1 (CANH) - I101-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN junction LH1 connector
I94-1 (CANH) - I94-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω Combination meter assembly


Wiring Color:
Code Color (CANH Side) Color (CANL Side) Connected to
I101 B W CAN junction LH1 connector
I94 R W Combination meter assembly


NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.




Result:
Result Proceed to
OK A
NG (Combination meter assembly main lines) B
NG (CAN junction LH1 connector main lines) C



A

REPLACE CAN JUNCTION RH1 CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN JUNCTION RH1 CONNECTOR - COMBINATION METER ASSEMBLY)

C

5.CHECK FOR OPEN IN CAN BUS LINES (CAN JUNCTION LH1 CONNECTOR)
5.CHECK FOR OPEN IN CAN BUS LINES (CAN JUNCTION LH1 CONNECTOR)
a.

Reconnect the I94 and I101 CAN junction RH1 connectors.


b.
C248235C05
0.292,1.635 0.667,1.885 0.375,0.25 2.76,1.385 3.073,1.615 0.313,0.229 0.656,2.104 0.385,2.104 true 0.781,2.177 0.927,2.438 0.927,2.438 0.927,2.635 true 2.896,1.979 2.604,1.688 2.604,1.688 2.396,1.688 true 2.719,2.115 2.385,2.115 true 2.833,2.177 2.833,2.49 2.833,2.49 2.354,2.49 true 0.917,2.01 1.156,2.01 true 0.927,2.156 1.083,2.417 1.083,2.417 1.188,2.417 true 2.938,2.208 2.938,2.885 true 1.229,1.917 1.885,2.156 0.656,0.24 10 false CANH*b 1.833,1.583 2.49,1.833 0.656,0.25 10 false CANH*c 1.26,2.323 1.896,2.563 0.635,0.24 10 false CANL*b 2.74,2.927 3.385,3.146 0.646,0.219 10 false CANL*c 0.24,2.021 0.49,2.313 0.25,0.292 10 false G 0.875,2.667 1.156,2.938 0.281,0.271 10 false W 2.219,2.031 2.479,2.26 0.26,0.229 10 false B 2.167,2.396 2.427,2.635 0.26,0.24 10 false W 0.146,0.115 0.469,0.448 0.323,0.333 10 false *a 0.354,1.677 0.74,1.948 0.385,0.271 10 false I104 2.833,1.417 3.042,1.646 0.208,0.229 10 false I93
*a Rear view of wire harness connector
(to CAN Junction LH1 Connector)
*b to ECM
*c to CAN Junction RH1 Connector


Disconnect the I93 and I104 CAN junction LH1 connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
I104-1 (CANH) - I104-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω ECM
I93-1 (CANH) - I93-2 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω CAN junction RH1 connector


Wiring Color:
Code Color (CANH Side) Color (CANL Side) Connected to
I104 G W ECM
I93 B W CAN junction RH1 connector


NOTICE:
·

Before disconnecting the connectors, make a note of where they are connected.

·

Reconnect each connector to its original position.




Result:
Result Proceed to
OK A
NG (CAN junction RH1 connector main lines) B
NG (ECM main lines) C



A

REPLACE CAN JUNCTION LH1 CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN JUNCTION LH1 CONNECTOR - CAN JUNCTION RH1 CONNECTOR)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (CAN JUNCTION LH1 CONNECTOR - ECM)