Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0104  Lost Communication with Driving Support ECU  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0104 Lost Communication with Driving Support ECU No communication from the driving support ECU assembly continues.
·

Driving support ECU assembly branch line or connector

·

Power source circuit of driving support ECU assembly

·

Driving support ECU assembly ground circuit

·

Driving support ECU assembly


The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11.

HINT:

This diagnostic procedure is for when DTC U0104 is output by the power management control ECU (GTS display: PM1 Gateway).


WIRING DIAGRAM

C318602E03
1.615,2.292 1.615,1.375 1.615,1.375 2,1.375 false 4.281,2.292 4.281,1.917 4.281,1.917 4.01,1.917 false 5.01,2.281 5.01,0.969 5.01,0.969 4.74,0.969 false 5.667,2.292 5.667,0.5 5.667,0.5 5.396,0.5 false 0.135,0.125 1.5,0.521 1.365,0.396 12 false Sub Bus 11: 1.438,6.021 3.313,6.365 1.875,0.344 10 false : CAN Main Bus Line (CANH) 1.438,6.448 3.313,6.792 1.875,0.344 10 false : CAN Main Bus Line (CANL) 4.406,6.031 6.281,6.375 1.875,0.344 10 false : CAN Branch Line (CANH) 4.406,6.438 6.281,6.781 1.875,0.344 10 false : CAN Branch Line (CANL) 5.5,4.802 6.365,5.208 0.865,0.406 10 false Trouble Area 2.958,5.094 5.01,5.396 2.052,0.302 10 false Driving Support ECU Assembly 2.99,4.531 3.25,4.781 0.26,0.25 10 false 30 2.115,4.771 3.156,5.01 1.042,0.24 10 false ECU-IG1 NO. 3 3.208,4.646 3.719,4.896 0.51,0.25 10 false B 3.5,4.094 3.76,4.344 0.26,0.25 10 false 39 4.125,4.094 4.385,4.344 0.26,0.25 10 false 17 4.625,4.531 4.885,4.781 0.26,0.25 10 false 25 4.26,4.635 4.667,4.906 0.406,0.271 10 false GND 3.896,4.313 4.323,4.552 0.427,0.24 10 false CA2L 0.542,3.219 0.958,3.469 0.417,0.25 10 false 120 Ω 0.135,3.813 1.375,4.313 1.24,0.5 10 false Power Management Control ECU 6.344,3.219 6.76,3.469 0.417,0.25 10 false 120 Ω 2.083,1.302 4.531,1.74 2.448,0.438 10 false CAN No. 5 Junction Connector 2.063,1.823 4.094,2.229 2.031,0.406 10 false CAN No. 6 Junction Connector 2.781,0.865 5.229,1.302 2.448,0.438 10 false CAN No. 2 Junction Connector 3.448,0.406 5.896,0.844 2.448,0.438 10 false CAN No. 3 Junction Connector 2.635,5.104 3,5.375 0.365,0.271 10 false I176 3.5,4.313 3.927,4.552 0.427,0.24 10 false CA2H 5.833,3.833 7.052,4.385 1.219,0.552 10 false CAN No. 4 Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG) and wait at least 20 seconds, and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 5.24 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.

Body Electrical > PM1 Gateway > Trouble Codes
50001 217
HINT:

If DTC U1002 is output from PM1 Gateway of the power management control ECU, this indicates a sub bus 11 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 11.



Result:
Result Proceed to
U1002 is not output from the power management control ECU (GTS display: PM1 Gateway) A
U1002 is output from the power management control ECU (GTS display: PM1 Gateway) B



A

2.CHECK FOR OPEN IN SUB BUS 11 LINES (DRIVING SUPPORT ECU ASSEMBLY BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN SUB BUS 11 LINES (DRIVING SUPPORT ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
E251017C85
0.667,0.698 1.094,0.979 0.427,0.281 2.167,2.583 2.344,2.583 2.344,2.583 2.698,1.938 true 2.229,0.865 2.417,0.865 2.417,0.865 2.729,1.729 true 1.865,0.771 2.271,1.021 0.406,0.25 10 false CA2L 1.76,2.479 2.156,2.688 0.396,0.208 10 false CA2H 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.75,0.771 1.063,0.969 0.313,0.198 10 false I176
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Disconnect the I176 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I176-39 (CA2H) - I176-17 (CA2L) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
E251017C86
0.667,0.698 1.094,0.979 0.427,0.281 1.292,1.917 0.906,2.552 0.906,2.552 0.719,2.552 true 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.76,0.76 1.073,0.958 0.313,0.198 10 false I176 0.375,2.458 0.833,2.656 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I176-25 (GND) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.
E251017C87
0.667,0.698 1.094,0.979 0.427,0.281 1.219,2.573 1.396,2.573 1.396,2.573 1.75,1.927 true 1.042,2.479 1.302,2.708 0.26,0.229 10 false B 0.083,0.104 0.396,0.302 0.313,0.198 10 false *a 0.75,0.76 1.063,0.958 0.313,0.198 10 false I176
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I176-30 (B) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)