Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR WINDOW FRAME MOULDING › from 2015.04
RM2040EQ _59 Vehicle Exterior _014740 EXTERIOR PANELS / TRIM _0075197 REAR DOOR WINDOW FRAME MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR WINDOW FRAME MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE LUGGAGE TRIM SERVICE HOLE COVER

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 69284D 4.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

Hide 74260 6.REMOVE REAR ARMREST ASSEMBLY

Hide 67604 7.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 68174A 8.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Hide 67842E 9.REMOVE REAR DOOR SERVICE HOLE COVER

Hide 68640A 10.REMOVE REAR DOOR CHECK ASSEMBLY

Hide 67872 11.REMOVE REAR DOOR WEATHERSTRIP

Hide 68152C 12.REMOVE REAR DOOR GLASS RUN

Hide 67408F 13.REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY

Hide 68124B 14.REMOVE REAR DOOR QUARTER WINDOW GLASS

Hide 68104 15.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Hide 75740 16.REMOVE REAR DOOR BELT MOULDING ASSEMBLY

Hide 75762A 17.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:

When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.


Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Rear Door Front Window Frame Moulding 20 to 30°C (68 to 86°F)

NOTICE:

Do not heat the vehicle body or rear door front window frame moulding excessively.


a.

Using a heat light, heat the rear door front window frame moulding.


b.
B381019C01
1.698,2.115 2.021,2.115 true 1.323,1.615 1.646,1.615 true 2.073,2.031 2.344,2.302 0.271,0.271 10 false *a 1.156,1.51 1.427,1.781 0.271,0.271 10 false *a
*a Caulking Sponge
V100155

Double-sided Tape


Using a moulding remover, disengage the clip and guide, and remove the rear door front window frame moulding.


Hide 75764A 18.REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING

a.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


b.
B381021N03
2.615,4.01 2.875,4.25 0.26,0.24 10 false A

Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement
A 5.0 mm (0.197 in.)


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 4 rivets.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.

·

Be careful of the drilled rivets, as they may be hot.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.


e.

Disengage the guide and remove the rear door upper window frame moulding from the door frame.


Hide 19.REMOVE REAR DOOR REAR WINDOW FRAME MOULDING

a.

Insert a 4.0 mm (0.157 in.) drill bit into a drill.


b.
B381023N01
1.833,4.146 2.073,4.375 0.24,0.229 10 false A

Tape a 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:
Area Measurement
A 5.0 mm (0.197 in.)


NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.



c.

Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 4 rivets.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Prying the rivets with the drill may damage the rivet installation holes or drill bit.

·

Be careful of the drilled rivets, as they may be hot.




d.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.


e.

Remove the rear door rear window frame moulding from the door frame.