Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2015.04
RM2040EQ _58 Vehicle Interior _014725 METER / GAUGE / DISPLAY _0075073 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The meter ECU uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge will vary between approximately 13 Ω with the float at the full position, and 414 Ω with the float at the empty position. The meter outputs auxiliary battery voltage through two resistors that are mounted inside the meter ECU. The meter ECU measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of the auxiliary battery voltage.

HINT:

The fuel level warning light will come on when the fuel level is below 9.8 liters (10.4 US qts, 8.6 Imp. qts).


WIRING DIAGRAM

E156126E59
5.26,2.938 7.094,3.281 1.833,0.344 10 false Combination Meter Assembly 6.073,0.896 6.313,1.052 0.24,0.156 10 false FR 6.073,2.25 6.365,2.406 0.292,0.156 10 false FE 5.813,0.885 6.188,1.156 0.375,0.271 10 false 14 5.823,2.24 6.156,2.604 0.333,0.365 10 false 15 2.125,2.229 2.24,2.375 0.115,0.146 10 false 3 2.115,0.885 2.229,1.031 0.115,0.146 10 false 2 0.292,3.052 2.063,3.49 1.771,0.438 10 false Fuel Suction Tube Assembly with Pump and Gauge 0.49,1.49 1.125,2.26 0.635,0.771 10 false Fuel Sender Gauge Assembly 1.302,1.427 1.417,1.573 0.115,0.146 10 false 2 1.302,2.094 1.417,2.24 0.115,0.146 10 false 1 1.802,2.24 2.021,2.385 0.219,0.146 10 false FE 1.813,0.885 2.01,1.042 0.198,0.156 10 false FS 5.26,2.771 5.75,3.052 0.49,0.281 10 false I18 0.292,2.885 0.573,3.031 0.281,0.146 10 false N11

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (FUEL METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Fuel Meter Operation Fuel receiver gauge OFF, Sender E, Empty, Warning, 1/4, 1/2, 3/4, Full, Sender F -
Body Electrical > Combination Meter > Active Test
Tester Display
Fuel Meter Operation
50004 122 3
OK:

Fuel receiver gauge indication is normal.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FUEL INPUT)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0 L, Max.: 127.5 L Fuel receiver gauge indicates F: 57.0
Fuel receiver gauge indicates 3/4: 46.5
Fuel receiver gauge indicates 1/2: 31.4
Fuel receiver gauge indicates 1/4: 14.8
Fuel receiver gauge indicates E: 5.5
Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data displayed on the GTS is almost same as the fuel receiver gauge indication. A
Fuel level data displayed on the GTS differs from the fuel receiver gauge indication. B



A

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)

B

REPLACE COMBINATION METER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE)
a.

Disconnect the I18 combination meter assembly and N11 fuel suction tube assembly with pump and gauge connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I18-14 (FR) - N11-2 (FS) Always Below 1 Ω
I18-15 (FE) - N11-3 (FE) Always Below 1 Ω
I18-14 (FR) - Body ground Always 10 kΩ or higher
I18-15 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2AR-FXE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2AR-FXE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

5.CHECK FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
a.

Visually check for deformation on the fuel suction tube assembly with pump and gauge connector.

OK:

There is no deformation.



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE