Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.04
RM2040EQ _57 Power Source / Network _014721 NETWORKING _0075042 CAN COMMUNICATION SYSTEM C

NETWORKING  CAN COMMUNICATION SYSTEM  U0233  Lost Communication with Blind Spot Monitor Master Module  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
U0233 Lost Communication with Blind Spot Monitor Master Module No communication from the blind spot monitor sensor RH continues.
·

Blind spot monitor sensor RH branch line or connector

·

Power source circuit of blind spot monitor sensor RH

·

Blind spot monitor sensor RH ground circuit

·

Blind spot monitor sensor RH


The power management control ECU stores DTCs when it detects a communication stop or network communication error for ECUs connected to sub bus 11.

HINT:

This diagnostic procedure is for when DTC U0233 is output by the power management control ECU (GTS display: PM1 Gateway).


WIRING DIAGRAM

C320676E02
2.396,2.281 2.396,1.906 2.396,1.906 2.729,1.906 false 1.688,2.292 1.688,1.531 1.688,1.531 1.896,1.531 false 5.573,2.292 5.573,0.667 5.573,0.667 5.333,0.667 false 5.167,2.292 5.167,1.094 5.167,1.094 4.927,1.094 false 0.125,0.094 5.344,0.615 5.219,0.521 12 false Sub Bus 11: 0.542,3.229 1,3.458 0.458,0.229 10 false 120 Ω 6.323,3.229 6.781,3.458 0.458,0.229 10 false 120 Ω 0.198,3.823 1.479,4.198 1.281,0.375 10 false Power Management Control ECU 2.854,1.823 4.917,2.25 2.063,0.427 10 false CAN No. 6 Junction Connector 1.979,1.448 4.042,1.875 2.063,0.427 10 false CAN No. 5 Junction Connector 5.823,3.833 7.052,4.281 1.229,0.448 10 false CAN No. 4 Junction Connector 3.021,1 5.083,1.427 2.063,0.427 10 false CAN No. 2 Junction Connector 3.021,5.115 4.927,5.385 1.906,0.271 10 false Blind Spot Monitor Sensor RH 2.146,4.802 3.177,5.052 1.031,0.25 10 false ECU-IG1 NO. 3 2.708,5.125 3.167,5.354 0.458,0.229 10 false O47 3.24,4.646 3.698,4.875 0.458,0.229 10 false BRB 3.51,4.313 3.969,4.542 0.458,0.229 10 false CA1P 3.927,4.313 4.385,4.542 0.458,0.229 10 false CA1N 4.156,4.625 4.615,4.854 0.458,0.229 10 false BRGD 3.052,4.542 3.24,4.781 0.188,0.24 10 false 5 3.573,4.104 3.76,4.344 0.188,0.24 10 false 2 4.135,4.104 4.323,4.344 0.188,0.24 10 false 7 4.635,4.531 4.875,4.75 0.24,0.219 10 false 10 5.469,4.781 6.5,5.031 1.031,0.25 10 false Trouble Area 1.448,6.021 3.563,6.313 2.115,0.292 10 false : CAN Main Bus Line (CANH) 1.438,6.438 3.552,6.729 2.115,0.292 10 false : CAN Main Bus Line (CANL) 4.438,6.438 6.552,6.729 2.115,0.292 10 false : CAN Branch Line (CANL) 4.427,6.021 6.542,6.313 2.115,0.292 10 false : CAN Branch Line (CANH) 3.385,0.583 5.448,1.01 2.063,0.427 10 false CAN No. 3 Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the power switch on (IG), turn the blind spot monitor main switch on, wait at least 11 seconds and then drive the vehicle at a speed of 5 km/h (3 mph) or more for at least 11.84 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Reconfirm DTCs.


Body Electrical > PM1 Gateway > Trouble Codes
50001 217
HINT:

If DTC U1002 is output from PM1 Gateway of the power management control ECU, this indicates a sub bus 11 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 11.


Result:
Result Proceed to
U1002 is not output from the power management control ECU (GTS display: PM1 Gateway) A
U1002 is output from the power management control ECU (GTS display: PM1 Gateway) B



A

2.CHECK FOR OPEN IN CAN BUS LINES (BLIND SPOT MONITOR SENSOR RH BRANCH LINE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS LINES (BLIND SPOT MONITOR SENSOR RH BRANCH LINE)
a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.
C285248C54
1.458,0.146 1.875,0.406 0.417,0.26 1.552,1.01 1.219,0.344 1.219,0.344 1.01,0.344 true 1.563,1.198 1.26,1.802 1.26,1.802 1.052,1.802 true 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 0.656,1.708 1.271,1.906 0.615,0.198 10 false CA1N 0.615,0.26 1.229,0.458 0.615,0.198 10 false CA1P 1.542,0.188 1.854,0.385 0.313,0.198 10 false O47
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Disconnect the O47 blind spot monitor sensor RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O47-2 (CA1P) - O47-7 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (BLIND SPOT MONITOR SENSOR RH)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C285248C55
1.479,0.167 1.896,0.427 0.417,0.26 1.927,1.208 2.146,1.813 2.146,1.813 2.313,1.813 true 0.125,0.073 0.438,0.229 0.313,0.156 10 false *a 2.375,1.719 2.99,1.917 0.615,0.198 10 false BRGD 1.563,0.219 1.875,0.417 0.313,0.198 10 false O47
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
O47-10 (BRGD) - Body ground Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) auxiliary battery terminal.


c.
C285248C56
1.479,0.167 1.896,0.427 0.417,0.26 1.938,0.99 2.188,0.385 2.188,0.385 2.365,0.385 true 0.125,0.073 0.438,0.229 0.313,0.156 10 false *a 2.406,0.302 3.021,0.5 0.615,0.198 10 false BRB 1.563,0.208 1.875,0.406 0.313,0.198 10 false O47
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
O47-5 (BRB) - Body ground Power switch on (IG) 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)