The power management control ECU and compressor with motor assembly transmit information to one another via a communication line. Compressor control is stopped and the DTC is stored if communication information is cut off or abnormal information occurs.
The DTC is also detected if high-voltage power supplied from the inverter with converter assembly to the compressor control circuit is shut off.
The DTC will be stored as a history DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1498/98 | Communication Malfunction (A/C Inverter Local) | ·
Communication line error or open between the power management control ECU and compressor with motor assembly ·
High-voltage power source is shut off |
·
Harness or connector between power management control ECU, compressor with motor assembly and body ground ·
Power management control ECU ·
Compressor with motor assembly ·
No. 4 engine wire (harness or connector between compressor with motor assembly and inverter with converter assembly) ·
Electric vehicle fuse ·
CAN communication system ·
Hybrid control system |
Memorized |
Wear electrically insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Be sure to carry the removed service plug grip because other workers may install it by mistake.
Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.
Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the power switch is turned on (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.
Using the intelligent tester to check if the CAN communication system is functioning normally.
| Result | Proceed to |
|---|---|
| CAN DTC is not output | A |
| CAN DTC is output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if DTCs for the hybrid control system are output using the intelligent tester.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| Only DTC P3108 is output | A |
| DTCs other than P3108 are output | B |
A
B
Do not disconnect the connector on the high-voltage side.
Disconnect the E65 compressor with motor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E65-5 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E65-6 (IG1) - E65-5 (GND) | Power switch on (IG) | 11 to 14 V |
| E65-6 (IG1) - E65-5 (GND) | Power switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A39 power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E65-1 (CLK) - A39-16 (CLK) | Always | Below 1 Ω |
| E65-2 (DIN) - A39-17 (ITE) | Always | Below 1 Ω |
| E65-3 (DOUT) - A39-18 (ETI) | Always | Below 1 Ω |
| E65-1 (CLK) - Body ground | Always | 10 kΩ or higher |
| E65-2 (DIN) - Body ground | Always | 10 kΩ or higher |
| E65-3 (DOUT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Turn the power switch off.
Remove the service plug grip.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL
Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.
After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.
Remove the connector cover assembly.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL
Be sure to prevent foreign objects or water from entering the inverter with converter assembly.
| *a | Electric Vehicle Fuse |
Check that bolts A and B are tightened securely.
Measure the resistance according to the value(s) in the table below.
| Tester Item
(Tester Connection) |
Condition | Specified Condition |
|---|---|---|
| Electric vehicle fuse(A - B) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Be sure to wear insulated gloves.
Disconnect the No. 4 engine wire connector.
Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>INVERTER WITH CONVERTER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-1 (PE) - G2-1 (ACPE) | Always | Below 1 Ω |
| G1-2 (PB) - G2-2 (ACPB) | Always | Below 1 Ω |
| G1-1 (PE) - Body ground | Always | 10 kΩ or higher |
| G1-2 (PB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the compressor with motor assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR>REMOVAL
Since the compressor with motor assembly cannot be inspected while it is removed from the vehicle, replace the compressor with motor assembly with a new or a known good one and check that the condition returns to normal.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B1498/98 is not output | A |
| DTC B1498/98 is output | B |
A
B