Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › INVERTER WITH CONVERTER
RM2040EQ _51 Engine / Hybrid System _014692 HYBRID / BATTERY CONTROL _0074888 INVERTER WITH CONVERTER A

HYBRID / BATTERY CONTROL  INVERTER WITH CONVERTER  REMOVAL  


PROCEDURE

Hide 4.REMOVE CONNECTOR COVER ASSEMBLY

CAUTION:
·

Do not touch the high voltage connectors and terminals for 10 minutes after the service plug grip is removed.

·

Wear insulated gloves.



NOTICE:

Do not start the hybrid system with the service plug grip removed because it may cause a malfunction.


a.
A258734

Remove the 2 bolts and connector cover assembly.

NOTICE:
·

Make sure to pull the connector cover assembly straight up, as a connector is connected to the bottom of the cover.

·

Do not allow any foreign objects or water to enter the inverter with converter assembly.




Hide 5.CHECK TERMINAL VOLTAGE

CAUTION:

Wear insulated gloves.


NOTICE:

Do not allow any foreign objects or water to enter the inverter with converter assembly.


a.
A258735

Using a voltmeter, measure the voltage between the terminals of the 2 phase connectors.

Standard voltage:

0 V


HINT:

Use a measuring range of DC 750 V or more on the voltmeter.



Hide 6.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

CAUTION:

Wear insulated gloves.


a.
A258736

Temporarily install the connector cover assembly with the bolt to prevent any foreign objects or water from entering the inverter with converter assembly.


Hide 53295E 7.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 17750A 8.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 17735 9.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 10.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 11.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide G9257 12.REMOVE NO. 5 INVERTER BRACKET

a.
A258737

Remove the 2 bolts and No. 5 inverter bracket.


Hide G9217 13.REMOVE NO. 4 INVERTER BRACKET

a.
A258738

Remove the 3 bolts and No. 4 inverter bracket.


Hide G9221B 14.REMOVE UPPER INVERTER COVER

CAUTION:

Wear insulated gloves.


a.
A258739

Remove the 2 bolts and upper inverter cover (generator cable side).

NOTICE:
·

Make sure to pull the upper inverter cover straight up, as a connector is connected to the bottom of the cover.

·

Do not touch the upper inverter cover waterproofing rubber.




Hide G2148 15.DISCONNECT GENERATOR CABLE

CAUTION:

Wear insulated gloves.


a.
A258740

Using an insulated tool, remove the 3 bolts.


b.
A258741

Disconnect the 2 wire harness clamps and separate the generator cable.

NOTICE:
·

Do not damage the terminals, connector housings or inverter with converter assembly when disconnecting them.

·

Do not touch the connector waterproofing rubber or terminals.

·

Insulate the removed terminals with insulating tape.

·

Do not allow any foreign objects or water to enter the inverter with converter assembly.




Hide G9221B 16.REMOVE UPPER INVERTER COVER

CAUTION:

Wear insulated gloves.


a.
A258742

Remove the 2 bolts and upper inverter cover (motor cable side).

NOTICE:
·

Make sure to pull the upper inverter cover straight up, as a connector is connected to the bottom of the cover.

·

Do not touch the upper inverter cover waterproofing rubber.




Hide G1148 17.DISCONNECT MOTOR CABLE

CAUTION:

Wear insulated gloves.


a.
A258743

Using an insulated tool, remove the 3 bolts.


b.
A258744

Disconnect the 3 wire harness clamps and separate the motor cable.

NOTICE:
·

Do not damage the terminals, connector housings or inverter with converter assembly when disconnecting them.

·

Do not touch the connector waterproofing rubber or terminals.

·

Insulate the removed terminals with insulating tape.

·

Do not allow any foreign objects or water to enter the inverter with converter assembly.




Hide G1143C 18.REMOVE NO. 3 MOTOR CABLE BRACKET

a.
A258748

Disconnect the hose clamp from the No. 3 motor cable bracket.

HINT:

Do not remove the hose clamp from the hose.



b.

Remove the 2 bolts and No. 3 motor cable bracket.


Hide 19.REMOVE CONNECTOR COVER ASSEMBLY

CAUTION:

Wear insulated gloves.


a.
A258751

Remove the bolt and connector cover assembly.

NOTICE:
·

Make sure to pull the connector cover assembly straight up, as a connector is connected to the bottom of the cover.

·

Do not allow any foreign objects or water to enter the inverter with converter assembly.




Hide 82124 20.DISCONNECT NO. 4 ENGINE WIRE

CAUTION:

Wear insulated gloves.


a.
A258749

Disconnect the No. 4 engine wire.

NOTICE:
·

Do not damage the terminals, connector housings or inverter with converter assembly when disconnecting them.

·

Do not touch the connector waterproofing rubber or terminals.

·

Insulate the removed terminals with insulating tape.

·

Do not allow any foreign objects or water to enter the inverter with converter assembly.




b.
A258750

Disconnect the wire harness clamp.


Hide 82164C 21.DISCONNECT NO. 4 FLOOR WIRE

a.
A258752

Remove the bolt.


b.
A258753

Disconnect the wire harness clamp and connector.

NOTICE:
·

Do not damage the terminals, connector housings or inverter with converter assembly when disconnecting them.

·

Do not touch the connector waterproofing rubber or terminals.

·

Insulate the removed terminals with insulating tape.

·

Do not allow any foreign objects or water to enter the inverter with converter assembly.




Hide 22.TEMPORARILY INSTALL CONNECTOR COVER ASSEMBLY

CAUTION:

Wear insulated gloves.


a.
A258736

Temporarily install the connector cover assembly with the bolt to prevent any foreign objects or water from entering the inverter with converter assembly.


Hide 23.DISCONNECT LOW VOLTAGE CONNECTOR

NOTICE:
·

Insulate the removed terminals with insulating tape.

·

Do not allow any foreign objects or water to enter the inverter with converter assembly.



a.
A258754

Raise the lock lever and disconnect the 3 low voltage connectors.


Hide 82113 24.DISCONNECT NO. 3 ENGINE ROOM WIRE

a.

Remove the relay block cover.


b.
A258761

Remove the nut.


c.

Disconnect the wire harness clamp and No. 3 engine room wire.


Hide G9228A 25.REMOVE NO. 4 INVERTER COOLING HOSE

a.
A258758C02
2.01,0.927 2.417,0.646 true 2.458,0.542 2.656,0.823 0.198,0.281 10 true *1
*1 Retainer


Release the retainer and disconnect the No. 4 inverter cooling hose from the inverter with converter assembly.


b.
A260009

Put pieces of cloth into the pipes and in the disconnected hoses, or cover the pipes and hoses with plastic bags as shown in the illustration to prevent foreign matter from entering the cooling system and to prevent coolant from spilling near the inverter with converter assembly.


Hide G90A0A 26.REMOVE NO. 1 INVERTER COOLING HOSE ASSEMBLY

a.
A258759C02
2.313,0.906 1.552,0.615 true 1.365,0.51 1.563,0.792 0.198,0.281 10 true *1
*1 Retainer


Release the retainer and disconnect the No. 1 inverter cooling hose from the inverter with converter assembly.


b.
A260010

Put pieces of cloth into the pipes and in the disconnected hoses, or cover the pipes and hoses with plastic bags as shown in the illustration to prevent foreign matter from entering the cooling system and to prevent coolant from spilling near the inverter with converter assembly.


Hide G9200 27.REMOVE INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

Wear insulated gloves.


a.
A258762C02
1.479,0.563 1.823,0.354 true 2.573,1.625 1.625,1.167 true 1.865,0.271 2.073,0.521 0.208,0.25 10 false *1 2.615,1.563 2.823,1.813 0.208,0.25 10 false *2
*1 No. 3 Engine Room Wire
*2 Hook


Temporarily secure the No. 3 engine room wire with the inverter with converter assembly hook as shown in the illustration.


b.
A258760

Remove the 2 bolts, nut and inverter with converter assembly.

NOTICE:
·

Since the inverter with converter assembly is very heavy, 2 people are needed to remove the inverter with converter assembly. When removing the inverter with converter assembly, do not damage the parts around it.

·

To prevent damage, do not hold the inverter with converter assembly by the connectors.

·

To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.




c.
A148374

Even after the coolant is drained, coolant remains in the inverter with converter assembly due to its internal structure. Therefore, seal or cover the pipes when removing the inverter with converter to prevent coolant from spilling out or foreign matter from entering the inverter with converter.


Hide 28.REMOVE HIGH VOLTAGE FUSE

CAUTION:

Wear insulated gloves.


HINT:

Perform this procedure only when replacement of the high voltage fuse is necessary.


a.
A260012

Remove the bolt and connector cover assembly.

NOTICE:
·

Make sure to pull the connector cover assembly straight up, as a connector is connected to the bottom of the cover.

·

Do not allow any foreign objects or water to enter the inverter with converter assembly.




b.
A260011

Remove the 2 nuts and high voltage fuse.


c.
A260012

Temporarily install the connector cover assembly with the bolt to prevent any foreign objects or water from entering the inverter with converter assembly.


Hide 17771A 29.REMOVE AIR CLEANER BRACKET

a.
A258765

Remove the bolt and air cleaner bracket.


Hide 17119A 30.REMOVE AIR CLEANER BRACKET

a.
A258767

Remove the bolt and air cleaner bracket.


Hide G9214 31.REMOVE NO. 1 INVERTER BRACKET

a.
A258764

Remove the 2 bolts and No. 1 inverter bracket.


Hide G9215 32.REMOVE NO. 2 INVERTER BRACKET

a.
A258763

Remove the 2 bolts and No. 2 inverter bracket.


Hide G9216 33.REMOVE NO. 3 INVERTER BRACKET

a.
A258766

Remove the 2 bolts and No. 3 inverter bracket.


Hide G1143A 34.REMOVE NO. 1 MOTOR CABLE BRACKET

a.
A258768

Remove the 2 bolts and No. 1 motor cable bracket.


Hide G1143B 35.REMOVE NO. 2 MOTOR CABLE BRACKET

a.
A258769

Remove the 2 bolts and No. 2 motor cable bracket.


Hide G9225J 36.REMOVE NO. 1 INVERTER COOLING HOSE

a.
A259452C02
2.124,0.087 2.325,0.368 0.201,0.281 10 *1 2.635,0.416 2.297,0.188 false
*1 Retainer


Release the retainer and disconnect the No. 1 inverter cooling hose from the inverter with converter assembly.


b.

Remove the No. 1 inverter cooling hose.


c.
A260009

Put pieces of cloth into the pipes and in the disconnected hoses, or cover the pipes and hoses with plastic bags as shown in the illustration to prevent foreign matter from entering the cooling system and to prevent coolant from spilling near the inverter with converter assembly.


Hide 82113 37.REMOVE NO. 3 ENGINE ROOM WIRE

a.
A258770

Open the cover.

NOTICE:

Do not twist the cover excessively when opening it.



b.

Remove the nut and No. 3 engine room wire.