Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2015.04
RM2040EQ _59 Vehicle Exterior _014733 WINDOW / GLASS _0075143 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a lane departure warning camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the lane departure warning camera may not be able to be installed due to a missing bracket or the lane departure alert system may not operate properly due to a difference in the transmissivity or black ceramic border.


PROCEDURE

Hide 56116C 1.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

Using a brush or sponge, coat the application area of 2 new No. 2 windshield glass stoppers with Primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install the 2 new No. 2 windshield glass stoppers onto the windshield glass, as shown in the illustration.

B280220C07
5.854,1.375 5.948,0.979 false 5.427,1.281 5.521,0.885 false 1.302,1.406 1.219,1.01 false 1.625,1.281 1.531,0.885 false 0.375,1.083 0.531,1.281 0.156,0.198 10 false a 6.688,1.083 6.844,1.281 0.156,0.198 10 false a 5.979,0.885 6.135,1.083 0.156,0.198 10 false *1 5.531,0.802 5.688,1 0.156,0.198 10 false *a 1.063,0.906 1.219,1.104 0.156,0.198 10 false *1 1.385,0.771 1.542,0.969 0.156,0.198 10 false *a 0.135,0.115 0.469,0.448 0.333,0.333 12 false *A
*A Back Side - -
*1 Ceramic Notch - -
*a Windshield Glass Edge Side - -


Standard Dimension:
Area Dimension
a 13.7 to 14.7 mm (0.539 to 0.578 in.)


NOTICE:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use the 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56115A 2.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B280219

Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

NOTICE:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56114 3.INSTALL WINDSHIELD GLASS RETAINER

a.

Using a brush or sponge, coat the application area of a new windshield outside moulding with Primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B280221C07
0.563,2.781 0.458,2.573 false 2.833,2.781 2.938,2.594 false 0.125,0.094 0.406,0.344 0.281,0.25 12 false *A 0.417,1.344 0.542,1.51 0.125,0.167 10 false A 0.302,1.813 0.427,1.979 0.125,0.167 10 false A 0.979,3.385 1.271,3.573 0.292,0.188 10 false A-A 0.313,2.5 0.521,2.688 0.208,0.188 10 false *1 2.958,2.521 3.167,2.708 0.208,0.188 10 false *1
*A Back Side
*1 Ceramic Notch


Install the 2 windshield glass retainers onto the windshield glass as shown in the illustration.


Hide 4.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the application area of a new windshield outside moulding with Primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B280253C07
1.281,0.313 1.417,0.469 0.135,0.156 10 false A 1.292,0.823 1.427,0.979 0.135,0.156 10 false A 0.948,2.177 1.219,2.427 0.271,0.25 10 false A-A 2.125,2.667 2.24,2.833 0.115,0.167 10 false a 0.177,0.125 0.479,0.385 0.302,0.26 12 false *A
*A Back Side


Install the windshield outside moulding onto the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 6.7 mm (0.264 in.)



Hide 56117A 5.INSTALL WINDOW GLASS ADHESIVE DAM

a.

Using a brush or sponge, coat the application area of a new window glass adhesive dam with Primer G.

B289717C04
5.396,1.688 6.99,3.104 1.594,1.417 5.396,0.208 6.99,1.625 1.594,1.417 3.729,0.208 5.323,1.625 1.594,1.417 0.74,2.75 0.448,2.802 false 4.031,2.75 4.25,2.865 false 3.833,2.75 3.563,2.813 3.563,2.813 3.438,2.698 false 0.406,3.469 0.75,3.656 0.344,0.188 10 false : *1 2.667,3.083 2.802,3.24 0.135,0.156 10 false A 2.646,2.698 2.781,2.854 0.135,0.156 10 false A 5.438,1.729 5.698,1.906 0.26,0.177 10 false C-C 5.438,0.25 5.698,0.427 0.26,0.177 10 false B-B 6.5,0.813 6.635,0.969 0.135,0.156 10 false c 3.771,0.25 4.031,0.427 0.26,0.177 10 false A-A 4.906,0.865 5.042,1.021 0.135,0.156 10 false a 4.677,0.448 4.813,0.604 0.135,0.156 10 false b 0.188,0.167 0.469,0.385 0.281,0.219 12 false *A 1.094,2.563 1.229,2.719 0.135,0.156 10 false B 0.906,2.958 1.042,3.115 0.135,0.156 10 false B 0.292,2.719 0.479,2.906 0.188,0.188 10 false *2 3.583,2.583 3.719,2.74 0.135,0.156 10 false C 3.781,2.979 3.917,3.135 0.135,0.156 10 false C 4.271,2.792 4.458,2.979 0.188,0.188 10 false *2 6.198,0.323 6.333,0.479 0.135,0.156 10 false b 6.125,1.802 6.26,1.958 0.135,0.156 10 false b 5.823,2.281 5.958,2.438 0.135,0.156 10 false c 3.281,2.594 3.469,2.781 0.188,0.188 10 false *3
*A Back Side - -
*1 Primer G *2 Ceramic Notch
*3 Label Area - -


Standard Dimension:
Area Dimension
a 33.0 mm (1.30 in.)
b 10.0 mm (0.394 in.)
c 55.0 mm (2.17 in.)


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.

Install the window glass adhesive dam onto the windshield glass as shown in the illustration.

B289722C04
1.438,2.281 1.438,2.396 1.438,2.396 0.74,2.396 false 1.375,2.281 1.375,2.396 false 0.844,2.104 0.844,2.396 false 4.167,2.104 4.271,2.292 false 1.875,2.313 2.031,2.083 false 0.208,0.146 0.531,0.406 0.323,0.26 12 false *A 0.573,2.323 0.802,2.51 0.229,0.188 10 false *1 4.865,0.656 5.156,0.833 0.292,0.177 10 false A-A 6.115,1.083 6.344,1.271 0.229,0.188 10 false a 4.229,2.302 4.458,2.49 0.229,0.188 10 false *1 1.969,1.927 2.198,2.115 0.229,0.188 10 false *2 2.771,2.458 2.906,2.615 0.135,0.156 10 false A 2.76,2.073 2.896,2.229 0.135,0.156 10 false A
*A Back Side - -
*1 Ceramic Notch *2 Window Glass Adhesive Dam


Standard Dimension:
Area Dimension
a 36.0 mm (1.42 in.)



Hide 56111 6.INSTALL WINDSHIELD GLASS SUB-ASSEMBLY

a.
B396343C01
1.667,0.708 1.417,0.708 false 1.667,0.354 1.417,0.354 1.417,0.354 1.417,0.854 false 1.365,0.875 1.677,1.031 0.313,0.156 10 false *1
*1 Matchmark


Position the windshield glass sub-assembly.

i.

Using suction cups, place the windshield glass sub-assembly in the correct position.


ii.

Check that the whole contact surface of the windshield glass sub-assembly rim is perfectly even.


iii.

Align the matchmarks on the windshield glass sub-assembly and vehicle body.

NOTICE:

Check that the windshield glass stoppers are attached to the vehicle body correctly.



iv.

Remove the windshield glass sub-assembly.



b.

Using a brush, coat the installation surface on the vehicle body with Primer M.

B280223C06
1.646,1.354 2.938,2.406 1.292,1.052 0.302,1.354 1.594,2.406 1.292,1.052 1.75,0.552 1.906,0.396 false 1.99,2.146 1.844,2.229 false 1.25,2.802 1.385,2.979 0.135,0.177 10 false A 1.177,3.167 1.313,3.344 0.135,0.177 10 false A 1.167,3.427 1.302,3.604 0.135,0.177 10 false B 0.521,3.24 0.656,3.417 0.135,0.177 10 true B 1.594,3.885 1.729,4.063 0.135,0.177 10 false C 1.635,4.271 1.771,4.448 0.135,0.177 10 false C 3.479,0.646 3.781,0.833 0.302,0.188 10 false A-A 3.479,2.656 3.781,2.844 0.302,0.188 10 false B-B 5.365,0.625 5.667,0.813 0.302,0.188 10 false C-C 0.365,1.385 0.542,1.563 0.177,0.177 10 false *a 1.719,1.396 1.896,1.573 0.177,0.177 10 false *b 1.906,0.26 2.083,0.438 0.177,0.177 10 false *1 1.688,2.177 1.865,2.354 0.177,0.177 10 false *3 0.344,4.51 0.708,4.708 0.365,0.198 10 false : *2
*1 Brush *2 Primer M
*3 Adhesive - -
*a CORRECT *b INCORRECT


NOTICE:
·

Do not coat the adhesive with Primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



c.

Using a brush or sponge, coat the application area of adhesive with Primer G.

B280225C05
4.073,1.885 3.969,2.063 false 3.188,1.885 3.281,2.073 false 2.281,0.896 2.438,1.073 0.156,0.177 10 false A 2.271,0.313 2.427,0.49 0.156,0.177 10 false A 0.625,0.781 0.781,0.958 0.156,0.177 10 false B 1.073,0.865 1.229,1.042 0.156,0.177 10 false B 1.604,1.719 1.76,1.896 0.156,0.177 10 false C 1.552,2.167 1.708,2.344 0.156,0.177 10 false C 1.854,2.833 2.125,2.99 0.271,0.156 10 false A-A 1.854,4.271 2.125,4.427 0.271,0.156 10 false B-B 3.792,4.26 4.063,4.417 0.271,0.156 10 false D-D 4.75,4.427 4.885,4.604 0.135,0.177 10 false d 3.781,2.813 4.052,2.969 0.271,0.156 10 false C-C 2.688,2.958 2.823,3.135 0.135,0.177 10 false a 2.438,5.135 2.573,5.313 0.135,0.177 10 false b 4.688,2.969 4.823,3.146 0.135,0.177 10 false c 0.25,0.177 0.552,0.375 0.302,0.198 12 false *A 0.365,5.573 0.604,5.74 0.24,0.167 10 false :*1 3.885,2.083 4.063,2.25 0.177,0.167 10 false *2 3.24,2.083 3.417,2.25 0.177,0.167 10 false *3 2.26,1.75 2.417,1.927 0.156,0.177 10 false D 2.25,2.229 2.406,2.406 0.156,0.177 10 false D
*A Back Side - -
*1 Primer G *2 Ceramic Notch
*3 Adhesive Center - -


Standard Dimension:
Area Dimension
a 9.6 mm (0.378 in.) or more
b 16.5 mm (0.650 in.) or more
c 18.5 mm (0.728 in.) or more
d 11.0 mm (0.433 in.) or more


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:
·

Apply Primer G onto the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.




d.

Apply adhesive to the glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800C46
1.198,0.448 1.74,0.802 false 0.76,1 0.854,1.156 0.094,0.156 10 false a 1.771,0.74 1.958,0.938 0.188,0.198 10 false *1 1.104,0.875 1.198,1.031 0.094,0.156 10 false a 0.563,0.615 0.656,0.771 0.094,0.156 10 false b 1.302,1.427 1.396,1.583 0.094,0.156 10 false b
*1 Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 8.0 mm (0.315 in.) or more
b 12.0 mm (0.472 in.) or more


HINT:

After cutting off the tip, use all adhesive within the time described in the table below.


Usage Time Frame:
Temperature Usage Time Frame
35°C (95°F) 15 minutes
20°C (68°F) 1 hour and 40 minutes
5°C (41°F) 8 hours



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the windshield glass sub-assembly as shown in the illustration.

B280226C05
4.073,1.885 3.969,2.063 false 3.219,1.865 3.313,2.052 false 2.281,0.896 2.438,1.073 0.156,0.177 10 false A 2.271,0.313 2.427,0.49 0.156,0.177 10 false A 0.625,0.792 0.781,0.969 0.156,0.177 10 false B 1.073,0.854 1.24,1.021 0.167,0.167 10 false B 1.604,1.719 1.76,1.896 0.156,0.177 10 false C 1.552,2.167 1.708,2.344 0.156,0.177 10 false C 0.25,0.177 0.583,0.385 0.333,0.208 12 false *A 0.365,5.573 0.604,5.74 0.24,0.167 10 false :*1 3.865,2.073 4.042,2.24 0.177,0.167 10 false *2 3.26,2.063 3.438,2.229 0.177,0.167 10 false *3 2.26,1.75 2.417,1.927 0.156,0.177 10 false D 2.25,2.229 2.406,2.406 0.156,0.177 10 false D 2.281,3.583 2.417,3.76 0.135,0.177 10 false a 2.365,5.229 2.5,5.406 0.135,0.177 10 false b 4.906,2.948 5.042,3.125 0.135,0.177 10 false c 4.75,2.875 4.885,3.052 0.135,0.177 10 false d 1.875,2.813 2.146,2.969 0.271,0.156 10 false A-A 1.865,4.25 2.135,4.406 0.271,0.156 10 false B-B 3.792,2.802 4.063,2.958 0.271,0.156 10 false C-C 4.781,4.302 4.917,4.479 0.135,0.177 10 false e 3.792,4.24 4.063,4.396 0.271,0.156 10 false D-D
*A Back Side - -
*1 Adhesive *2 Ceramic Notch
*3 Adhesive Center - -


Standard Dimension:
Area Dimension
a 9.5 mm (0.374 in.)
b 9.5 mm (0.374 in.)
c 4.0 mm (0.157 in.)
d 8.0 mm (0.315 in.)
e 4.0 mm (0.157 in.)


HINT:

Apply adhesive onto the ceramic notches.




e.
B396343C01
1.667,0.708 1.417,0.708 false 1.667,0.354 1.417,0.354 1.417,0.354 1.417,0.854 false 1.365,0.875 1.677,1.031 0.313,0.156 10 false *1
*1 Matchmark


Install the windshield glass sub-assembly.

i.

Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the windshield glass stoppers are attached to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass sub-assembly.




ii.

Lightly press the front surface of the windshield glass sub-assembly to ensure that the windshield glass is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the windshield glass using protective tape until the applied adhesive becomes hard.

NOTICE:

Do not drive the vehicle for the time described in the table below.


Minimum Time:
Temperature Minimum Time prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




f.

w/ Front Window Deicer System:

i.

Engage each clamp and connect the connector.



Hide 7.INSPECT FOR LEAK AND REPAIR

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 8.INSTALL ROOF HEADLINING ASSEMBLY

a.

Return the front section of the roof headlining assembly to the original position.


Hide 74310 10.INSTALL VISOR ASSEMBLY RH

Hide 74325 11.INSTALL VISOR BRACKET COVER (for RH Side)

Hide 74320 12.INSTALL VISOR ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 74325 13.INSTALL VISOR BRACKET COVER (for LH Side)

HINT:

Use the same procedure as for the RH side.


Hide 63318C 14.INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

Hide 74620C 15.INSTALL REAR ASSIST GRIP ASSEMBLY RH

Hide 74630E 16.INSTALL REAR ASSIST GRIP ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 74610A 17.INSTALL ASSIST GRIP SUB-ASSEMBLY (for RH Side)

Hide 74610A 18.INSTALL ASSIST GRIP SUB-ASSEMBLY (for LH Side)

HINT:

Use the same procedure as for the RH side.


Hide 81360T 19.INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)

Hide 81240 20.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)

Hide 63650A 21.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)

Hide 63650A 22.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)

Hide 62211 23.INSTALL FRONT PILLAR GARNISH RH

Hide 62311B 24.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 62212 25.INSTALL FRONT PILLAR GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 62312B 26.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 86468 27.INSTALL LANE DEPARTURE WARNING CAMERA (w/ Lane Departure Alert System)

Hide 89941 28.INSTALL RAIN SENSOR (w/ Rain Sensor)

Hide 87810 29.INSTALL INNER REAR VIEW MIRROR ASSEMBLY

Hide 55781E 30.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53866J 31.INSTALL FRONT FENDER TO COWL SIDE SEAL RH

Hide 53867H 32.INSTALL FRONT FENDER TO COWL SIDE SEAL LH

HINT:

Use the same procedure as for the RH side.


Hide 33.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 34.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH