Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › from 2015.04
RM2040EQ _58 Vehicle Interior _014732 INTERIOR PANELS / TRIM _0075129 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  INSTALLATION  


PROCEDURE

Hide 1.INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

a.
B279105C20
2.26,1.552 2.677,1.844 0.417,0.292 10 false *b 1.292,0.885 1.646,1.188 0.354,0.302 10 false *a
*a Clip (Black)
*b Clip (White)


Install the 2 clips to the roof headlining assembly.


b.
B279011

Put the roof headlining assembly into the vehicle through the front passenger side door.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.



c.

Engage the 2 clips.

B396414C01
5.26,4.208 5.635,4.448 0.375,0.24 12 false *A
*A w/ Digital Audio Broadcasting Antenna - -



d.

Install the roof headlining assembly with the 2 clips.


e.

Engage the 4 clamps to the front pillar LH.


f.

Engage the 3 clamps to the front pillar RH.


g.

Connect the bracket with the bolt to the front pillar RH.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


h.

Engage the 2 clamps and connect the connector to the rear pillar RH.


i.

w/ Digital Audio Broadcasting Antenna:

i.

Engage the clamp and connect the connector to the rear pillar LH.



j.

w/ Lane Departure Alert System:

i.

Connect the connector to the lane departure warning camera.


ii.

Connect the connector to the rain sensor.


iii.

Connect the connector to the inner rear view mirror.



Hide 2.INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

a.
B279105C20
2.26,1.552 2.677,1.844 0.417,0.292 10 false *b 1.292,0.885 1.646,1.188 0.354,0.302 10 false *a
*a Clip (Black)
*b Clip (White)


Install the 2 clips to the roof headlining assembly.


b.
B279012

Put the roof headlining assembly into the vehicle through the front passenger side door.

NOTICE:

Do not damage the roof headlining assembly or vehicle interior.



c.

Engage the 2 clips and 2 fasteners.

B396416C01
5.25,4.219 5.625,4.458 0.375,0.24 12 false *A
*A w/ Digital Audio Broadcasting Antenna - -



d.

Install the roof headlining assembly with the 2 clips.


e.

Engage the 4 clamps to the front pillar LH.


f.

Engage the 3 clamps to the front pillar RH.


g.

Connect the bracket with the bolt to the front pillar RH.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


h.

Engage the 2 clamps and connect the connector to the rear pillar RH.


i.

Connect the connector to the sliding roof drive gear assembly.


j.

w/ Digital Audio Broadcasting Antenna:

i.

Engage the clamp and connect the connector to the rear pillar LH.



k.

w/ Lane Departure Alert System:

i.

Connect the connector to the lane departure warning camera.


ii.

Connect the connector to the rain sensor.


iii.

Connect the connector to the inner rear view mirror.



Hide 74348 3.INSTALL VISOR HOLDER

a.
B211698

Engage the 2 claws.


b.

Push in the visor holder as shown in the illustration.

HINT:

Use the same procedure for the other visor holder.



Hide 74310 4.INSTALL VISOR ASSEMBLY RH

a.

Install the visor assembly RH with the 2 screws.


Hide 74325 5.INSTALL VISOR BRACKET COVER (for RH Side)

a.
B287230

Engage the 4 claws to install the visor bracket cover.


Hide 74320 6.INSTALL VISOR ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 74325 7.INSTALL VISOR BRACKET COVER (for LH Side)

HINT:

Use the same procedure as for the RH side.


Hide 63318C 8.INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

a.
B279103C05
0.531,2.344 0.344,2.219 false 1,2.719 1.104,2.875 false 1.063,2.896 1.406,3.146 0.344,0.25 10 false *2 0.167,2.104 0.542,2.344 0.375,0.24 10 false *1
*1 Notch
*2 Alignment Mark


Align the alignment mark on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.

NOTICE:

After installation, check that the corners fit correctly.



Hide 74610A 9.INSTALL ASSIST GRIP SUB-ASSEMBLY (for RH Side)

a.
B287238

Put an assist grip sub-assembly together as shown in the illustration.


b.
B287240

Engage the 2 clips to install the assist grip sub-assembly.


c.
B287233

Engage the 4 claws to install the 2 assist grip covers.


Hide 74610A 10.INSTALL ASSIST GRIP SUB-ASSEMBLY (for LH Side)

HINT:

Use the same procedure as for the RH side.


Hide 74620C 11.INSTALL REAR ASSIST GRIP ASSEMBLY RH

a.
B287239

Put an rear assist grip assembly RH together as shown in the illustration.


b.
B287241

Engage the 2 clips to install the rear assist grip assembly RH.


c.
B287235

Engage the 4 claws to install the 2 assist grip covers.


Hide 74630E 12.INSTALL REAR ASSIST GRIP ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 81240 13.INSTALL NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)

Hide 81360T 14.INSTALL SPOT LIGHT ASSEMBLY (w/ Sliding Roof)

Hide 63650A 15.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)

Hide 63650A 16.INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)

Hide 86466 17.INSTALL NO. 1 LANE DEPARTURE WARNING CAMERA COVER (w/ Lane Departure Alert System)

Hide 86466C 18.INSTALL NO. 2 LANE DEPARTURE WARNING CAMERA COVER (w/ Lane Departure Alert System)

Hide 89943 19.INSTALL RAIN SENSOR COVER (w/ Lane Departure Alert System)

Hide 22.INSTALL FRONT SEAT ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 62471A 23.INSTALL ROOF SIDE INNER GARNISH RH

a.

Engage the 2 guides.


b.

Engage the 5 clips to install the roof side inner garnish RH.


Hide 62411B 24.INSTALL CENTER PILLAR UPPER GARNISH RH

a.

Pass the floor anchor of the front seat outer belt assembly RH through the center pillar upper garnish RH.


b.

Engage the clip.


c.

Install the center pillar upper garnish RH with the 2 screws.


Hide 62413A 25.INSTALL CENTER PILLAR LOWER GARNISH RH

a.

Engage the 2 claws and 3 clips to install the center pillar lower garnish RH.


Hide 73210 26.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

Hide 73233 27.INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)

Hide 62331A 28.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

a.
B334264C13
1.458,3.594 1.385,3.313 1.385,3.313 1.198,3.313 false 1.052,3.198 1.365,3.396 0.313,0.198 10 false *a
*a Alignment Mark (Blue)


Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

NOTICE:

After installation, check that the corners fit correctly.



Hide 67917A 29.INSTALL REAR DOOR SCUFF PLATE RH

a.

Engage the 6 claws to install the rear door scuff plate LH.

HINT:

Engage the claws from the rear side of the scuff plate.



Hide 62472A 30.INSTALL ROOF SIDE INNER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 62412B 31.INSTALL CENTER PILLAR UPPER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 62414A 32.INSTALL CENTER PILLAR LOWER GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 73220 33.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 73233 34.INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side)

HINT:

Use the same procedure as for the RH side.


Hide 62332A 35.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.
B334263C15
1.948,3.604 2.042,3.365 2.042,3.365 2.167,3.365 false 2.188,3.25 2.5,3.448 0.313,0.198 10 false *a
*a Alignment Mark (Red)


Align the alignment mark (Red) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.

NOTICE:

After installation, check that the corners fit correctly.



Hide 67918A 36.INSTALL REAR DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.


Hide 37.INSTALL REAR SIDE SEATBACK ASSEMBLY LH

Hide 38.INSTALL REAR SIDE SEATBACK ASSEMBLY RH

Hide 39.INSTALL REAR SEATBACK ASSEMBLY LH

Hide 64277C 40.INSTALL NO. 2 ROOM PARTITION COVER

Hide 41.INSTALL REAR SEATBACK ASSEMBLY RH

Hide 72693 42.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 43.INSTALL REAR SEAT CUSHION ASSEMBLY

Hide 62211 44.INSTALL FRONT PILLAR GARNISH RH

a.

Remove the protective cover.


b.

Make sure that the front pillar garnish clip is not damaged.

NOTICE:

If the front pillar garnish clip is damaged, replace the front pillar garnish clip with a new one.



c.
B287224

Install the front pillar garnish clip to front pillar garnish RH.

HINT:

Install the front pillar garnish clip so that it faces as shown in the illustration.

B453137C01
0.833,0.167 1.146,0.323 0.313,0.156 10 false *a 2.917,0.167 3.229,0.323 0.313,0.156 10 false *b 5.083,0.167 5.396,0.323 0.313,0.156 10 false *b
*a Correct *b Incorrect




d.

Engage the 2 guides as shown in the illustration.


e.
B287221

Engage the front pillar garnish clip and clip to install the front pillar garnish RH.

HINT:

Make sure that the curtain shield airbag assembly RH is not pinched.



Hide 62311B 45.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.
B334262C13
1.094,3.24 1.344,3.24 1.344,3.24 1.458,3.604 false 0.938,3.156 1.25,3.354 0.313,0.198 10 false *a
*a Alignment Mark (White)


Align the alignment mark (White) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

NOTICE:

After installation, check that the corners fit correctly.



Hide 62111A 46.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

a.
B294698

Insert the 2 clips as shown in the illustration to engage them.


b.

Install the cowl side trim sub-assembly RH with the clip.


Hide 67913 47.INSTALL FRONT DOOR SCUFF PLATE RH

a.

Engage the 10 claws to install the front door scuff plate RH.


Hide 62212 48.INSTALL FRONT PILLAR GARNISH LH

HINT:

Use the same procedure as for the RH side.


Hide 62312B 49.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B334260C13
1.948,3.615 2.01,3.344 2.01,3.344 2.167,3.344 false 2.188,3.229 2.5,3.427 0.313,0.198 10 false *a
*a Alignment Mark (Yellow)


Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the vehicle body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

NOTICE:

After installation, check that the corners fit correctly.



Hide 62112A 50.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

HINT:

Use the same procedure as for the RH side.


Hide 67914 51.INSTALL FRONT DOOR SCUFF PLATE LH

HINT:

Use the same procedure as for the RH side.


Hide 52.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 64718C 53.INSTALL LUGGAGE TRIM SERVICE HOLE COVER