DTC U0100 Lost Communication with ECM / PCM "A" |
DTC U0129 Lost Communication with Brake System Control Module |
DTC U0293 Lost Communication with HV ECU |
| DTC No. | DTC Detection Condition | Trouble Area |
| U0100 | The power management control ECU does not receive data from the ECM. |
|
| U0129 | The power management control ECU does not receive data from the brake booster with master cylinder assembly (skid control ECU). |
|
| U0293 |
|
|

| 1.RECONFIRM DTC OUTPUT |
Check if Hybrid Control of the power management control ECU outputs only DTC U0129.
| Result | Proceed to |
| The power management control ECU outputs DTC U0129 and other DTCs. (Intelligent tester display: Hybrid Control) | A |
| The power management control ECU outputs only DTC U0129. (Intelligent tester display: Hybrid Control) | B |
|
| ||||
| A | |
| 2.CHECK SUB BUS 15 |
Disconnect the cable from the negative (-) auxiliary battery terminal.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
| I4-31 (CA3P) - I4-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or higher: Open circuit in a main bus line | |||
| I4-31 (CA3P) - I4-4 (E12) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANH ground short |
| I4-30 (CA3N) - I4-4 (E12) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Below 200 Ω: CANL ground short |
| *a | Component with harness connected (Power Management Control ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
| I4-31 (CA3P) - I4-7 (AM21) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| I4-30 (CA3N) - I4-7 (AM21) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
| OK | A |
| NG (Open circuit in CAN main bus line) | B |
| NG (Short circuit between bus lines) | C |
| D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 3.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (POWER MANAGEMENT CONTROL ECU) |
![]() |
Disconnect the power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I4-31 (CA3P) - I4-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to Power Management Control ECU) |
|
| ||||
| OK | ||
| ||
| 4.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (CAN NO. 1 J/C) |
Reconnect the power management control ECU connector.
![]() |
Disconnect the CAN No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| A72-2 (CANH) - A72-8 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| A72-3 (CANH) - A72-9 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Power management control ECU |
| *a | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *b | to ECM |
| *c | to Power Management Control ECU |
| Result | Proceed to |
| OK | A |
| NG (Open circuit in power management control ECU CAN main bus line) | B |
| NG (Open circuit in ECM CAN main bus line) | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 5.CHECK FOR OPEN IN SUB BUS 15 MAIN LINES (ECM - CAN NO. 1 J/C) |
Reconnect the CAN No. 1 junction connector.
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-12 (CANP) - A25-25 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 6.CHECK FOR SHORT IN SUB BUS 15 LINES (POWER MANAGEMENT CONTROL ECU) |
![]() |
Disconnect the power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I4-31 (CA3P) - I4-30 (CA3N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Rear view of wire harness connector (to Power Management Control ECU) |
|
| ||||
| OK | ||
| ||
| 7.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 1 J/C) |
Reconnect the power management control ECU connector.
![]() |
Disconnect the CAN No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| A72-1 (CANH) - A72-7 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Brake booster with master cylinder assembly (skid control ECU) |
| A72-2 (CANH) - A72-8 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | ECM |
| A72-3 (CANH) - A72-9 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω | Power management control ECU |
| *a | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *b | to ECM |
| *c | to Power Management Control ECU |
| *d | to Brake Booster with Master Cylinder Assembly (skid control ECU) |
| Result | Proceed to |
| OK | A |
| NG (Short circuit between bus lines in power management control ECU CAN main bus line) | B |
| NG (Short circuit between bus lines in ECM CAN main bus line) | C |
| NG (Short circuit between bus lines in brake booster with master cylinder assembly (skid control ECU) CAN branch line) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 8.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN NO. 1 J/C) |
Reconnect the CAN No. 1 junction connector.
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-12 (CANP) - A25-25 (CANN) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132 Ω |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 9.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER - CAN NO. 1 J/C) |
Reconnect the CAN No. 1 junction connector.
![]() |
Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A28-35 (CA2H) - A28-34 (CA2L) | Cable disconnected from negative (-) auxiliary battery terminal | 54 to 69 Ω |
| *a | Front view of wire harness connector (to Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
| Result | Proceed to |
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 10.CHECK FOR SHORT IN SUB BUS 15 LINES (CAN NO. 1 J/C) |
![]() |
Disconnect the CAN No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
| A72-1 (CANH) - GND | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Brake booster with master cylinder assembly (skid control ECU) |
| A72-7 (CANL) - GND | |||
| A72-2 (CANH) - GND | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | ECM |
| A72-8 (CANL) - GND | |||
| A72-3 (CANH) - GND | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher | Power management control ECU |
| A72-9 (CANL) - GND | |||
| A72-1 (CANH) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Brake booster with master cylinder assembly (skid control ECU) |
| A72-7 (CANL) - +B | |||
| A72-2 (CANH) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | ECM |
| A72-8 (CANL) - +B | |||
| A72-3 (CANH) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher | Power management control ECU |
| A72-9 (CANL) - +B |
| *a | Front view of wire harness connector (to CAN No. 1 Junction Connector) |
| *b | to ECM |
| *c | to Power Management Control ECU |
| *d | to Brake Booster with Master Cylinder Assembly (Skid Control ECU) |
| Result | Proceed to |
| OK | A |
| B |
| C |
| D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 11.CHECK FOR SHORT IN SUB BUS 15 LINES (POWER MANAGEMENT CONTROL ECU - CAN NO. 1 J/C) |
![]() |
Disconnect the power management control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I4-31 (CA3P) - GND | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| I4-30 (CA3N) - GND | ||
| I4-31 (CA3P) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| I4-30 (CA3N) - +B |
| *a | Rear view of wire harness connector (to Power Management Control ECU) |
|
| ||||
| OK | ||
| ||
| 12.CHECK FOR SHORT IN SUB BUS 15 LINES (ECM - CAN NO. 1 J/C) |
![]() |
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-12 (CANP) - GND | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A25-25 (CANN) - GND | ||
| A25-12 (CANP) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A25-25 (CANN) - +B |
| *a | Front view of wire harness connector (to ECM) |
|
| ||||
| OK | ||
| ||
| 13.CHECK FOR SHORT IN SUB BUS 15 LINES (BRAKE BOOSTER WITH MASTER CYLINDER - CAN NO. 1 J/C) |
![]() |
Disconnect the brake booster with master cylinder assembly (skid control ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A28-35 (CA2H) - GND | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| A28-34 (CA2L) - GND | ||
| A28-35 (CA2H) - +B | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| A28-34 (CA2L) - +B |
| *a | Front view of wire harness connector (to Brake Booster with Master Cylinder Assembly (Skid Control ECU)) |
| Result | Proceed to |
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
|
| ||||
|
| ||||
| A | ||
| ||