Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM (for Start Function)

SMART ENTRY AND START SYSTEM (for Start Function) > Power Source Mode does not Change to ON (IG and ACC)

for Preparation Click here


DESCRIPTION

If any of the following operations are performed, the power management control ECU receives a signal, and changes the power source mode.
  1. With the electrical key transmitter sub-assembly in the cabin, the power switch is pressed.
  2. When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the power switch.
  3. When the smart entry and start system cancel function has been canceled on the customization menu, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the power switch.

HINT:
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


WIRING DIAGRAM


B388788E01


B298915E02


INSPECTION PROCEDURE

NOTICE:
  1. When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
    for Power Source Control: Body / Power Source Control / DTC.
    for Entry&Start: Body / Entry&Start / DTC.
  2. The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
  3. Before replacing the electrical key transmitter sub-assembly, refer to the smart entry and start system (for Start Function) precaution (Click here).
  4. Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (Click here).
  5. If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (Click here).
  6. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  7. After completing repairs, confirm that the problem does not occur.


HINT:

Related Data List and Active Test Items 
Problem Symptom
Data List Item
Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
  1. Start Switch1
  2. Start Switch2
  3. Power Supply Condition
  4. IG1 Relay Monitor(Inside)
  5. IG2 Relay Monitor(Inside)
  6. IG1 Relay Monitor(Outside)
  7. IG2 Relay Monitor(Outside)
  8. Latch Circuit
  9. ACC Relay Monitor
-

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
  1. Check the wireless door lock function by operating the electrical key transmitter sub-assembly.

    OK:
    Wireless door lock function operates.



NG
GO TO OTHER FLOW CHART (All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate) (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
B223988E07
  1. Disconnect the I3 and I4 connectors from the power management control ECU.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I3-1 (AM22) - Body ground
    Power switch off
    11 to 14 V
    I4-7 (AM21) - Body ground
    Power switch off
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE
OK


3.CHECK HARNESS AND CONNECTOR (GROUND)
B223988E08
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I3-5 (E01) - Body ground
    Always
    Below 1 Ω
    I3-6 (E1) - Body ground
    Always
    Below 1 Ω
    I4-4 (E12) - Body ground
    Always
    Below 1 Ω
    I4-5 (E02) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SMART ENTRY AND START SYSTEM
  1. Remove the transmitter battery from the electrical key transmitter sub-assembly (Click here).



    B282001E01
  1. With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch and check if the power source mode changes.

    OK:
    The power source mode changes.

    HINT:
    If the power source mode changes, the cabin verification is malfunctioning.

    Result:
    Result
    Proceed to
    The power source mode does not change.
    A
    The power source mode changes.
    B

    Text in Illustration 
    *1
    Power Switch
    *2
    Electrical Key Transmitter Sub-assembly



B
Go to step 8
A


5.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Power Source Control / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Specified Condition
    Stop Light Switch1
    State of brake pedal/ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    1. Use this item to determine whether the stop light switch is malfunctioning.
    2. The hybrid control system cannot be started when this item is OFF.
    3. When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.

    OK:
    ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.



NG
Go to step 11
OK


6.READ VALUE USING INTELLIGENT TESTER
  1. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Power Supply Condition
    Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
    All OFF: Power switch off
    ACC ON: Power switch on (ACC)
    IG1 ON: Power switch on (IG) (IG1 relay on)
    IG2 ON: Power switch on (IG) (IG2 relay on)
    ST ON: Sending hybrid control system start request signal
    Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).

  1. With the power switch off and brake pedal depressed, hold the electrical key transmitter sub-assembly near the power switch for 2 seconds or more and read the Data List.

    OK:
    IG2 ON is displayed in the Data List.

    HINT:
    If the smart entry and start system function has been canceled on the customization menu, ACC ON is displayed in the Data List.



NG
Go to step 13
OK


7.CHECK POWER MANAGEMENT CONTROL ECU
  1. Read the Data List according to the display on the intelligent tester.



    B224008E02
  1. Measure the voltage according to the value(s) in the table below.
    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)

  1. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Power Supply Condition
    Power supply state/IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
    All OFF: Power switch off
    ACC ON: Power switch on (ACC)
    IG1 ON: Power switch on (IG) (IG1 relay on)
    IG2 ON: Power switch on (IG) (IG2 relay on)
    ST ON: Sending hybrid control system start request signal
    Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).

  1. Measure the voltage while checking the Data List on the intelligent tester.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I4-2 (IG1D) - Body ground
    Power switch off
    1 V or less
    Power switch on (ACC)
    1 V or less
    Power switch on (IG)
    9 V or higher
    A39-2 (IG2D) - Body ground
    Power switch off
    1 V or less
    Power switch on (ACC)
    1 V or less
    Power switch on (IG)
    9 V or higher
    I4-1 (ACCD) - Body ground
    Power switch off
    1 V or less
    Power switch on (IG)
    8.5 V or higher
    Power switch on (ACC)
    8.5 V or higher



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

CHECK RELAY CONTACT SIDE CIRCUIT 

8.READ VALUE USING INTELLIGENT TESTER
  1. Read the Data List according to the display on the intelligent tester.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Start Switch1
    Power switch 1 status/ON or OFF
    ON: Power switch pressed
    OFF: Power switch not pressed
    1. If the power switch is pressed for a short time, the display may not change.
    2. Use this item to determine whether the power switch input signal is malfunctioning.
    Start Switch2
    Power switch 2 status/ON or OFF
    ON: Power switch pressed
    OFF: Power switch not pressed
    1. Backup for power switch 1. However, when the power switch is pressed and held, the control functions only when both power switch 1 and 2 are normal.
    2. Behaves the same way as power switch 1.

    OK:
    ON (Power switch is pressed) and OFF (Power switch is not pressed) appear on the screen.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
GO TO OTHER FLOW CHART (Room Oscillator does not Recognize Key) (Click here)
A


9.INSPECT POWER SWITCH
  1. Inspect the power switch (Click here).



NG
REPLACE POWER SWITCH (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - POWER SWITCH)
  1. Disconnect the I3 and I4 connectors from the power management control ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I3-7 (SSW1) - I58-5 (SS1)
    Always
    Below 1 Ω
    I4-17 (SSW2) - I58-1 (SS2)
    Always
    Below 1 Ω
    I3-7 (SSW1) or I58-5 (SS1) - Body ground
    Always
    10 kΩ or higher
    I4-17 (SSW2) or I58-1 (SS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the A39 power management control ECU connector.

  1. Disconnect the A77 stop light switch assembly connector.



    E233265E91
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A77-1 (B) - Body ground
    Power switch off
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I4-10 (STP) - A77-4 (L)
    Always
    Below 1 Ω
    I4-10 (STP) or A77-4 (L) - Body ground
    Always
    10 kΩ or higher
    A77-3 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Stop Light Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.INSPECT STOP LIGHT SWITCH ASSEMBLY
  1. Inspect the stop light switch assembly (Click here).



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

13.CHECK FOR DTC
  1. Enter the following menus:
    for Entry&Start: Body / Entry&Start / Trouble Codes.

  1. Check for DTCs.

    Result:
    Result
    Proceed to
    The following DTCs are not output:
    1. B2785
    2. B2287
    3. B2784
    A
    DTC B2785 is not output but DTC B2287 is output.
    B
    DTCs other than B2287 are output.
    C



B
GO TO FLOW CHART (DTC B2287) (Click here)

C
GO TO OTHER FLOW CHART
A

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY (Click here)