Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM (w/ EGR System)

DTC    P0401    Exhaust Gas Recirculation Flow Insufficient Detected

for Preparation Click here


DESCRIPTION

Based on the driving conditions, the ECM regulates the volume of exhaust gas that is recirculated to the engine's combustion chambers and thus lowers the combustion temperature to reduce NOx emissions. The ECM monitors signals such as engine speed, coolant temperature, electric load, and vehicle speed. When the EGR permission conditions are fulfilled, the ECM controls the opening of the EGR valve linearly through signals to the EGR step motor.

DTC No.
DTC Detection Condition
Trouble Area
P0401
Change in intake manifold pressure is small when the EGR valve is opened and closed during idle fuel cut operation (2 trip detection logic).
  1. EGR valve assembly
  2. EGR passage
  3. EGR cooler assembly
  4. Manifold absolute pressure sensor
  5. Intake system

MONITOR DESCRIPTION

The ECM monitors the pressure inside the intake manifold while opening and closing the EGR valve during fuel cut operation. If there is no change in the manifold absolute pressure sensor value, the ECM interprets this as a malfunction in the EGR valve assembly, illuminates the MIL and stores the DTC (2 trip detection logic).

MONITOR STRATEGY


Required Sensors/Components (Main)
EGR valve assembly
Manifold absolute pressure sensor
Required Sensors/Components (Related)
Engine coolant temperature sensor
Vehicle speed sensor
Frequency of Operation
Once per driving cycle

TYPICAL ENABLING CONDITIONS


Engine speed
950 to 1600 rpm
Vehicle speed
20 km/h (12.4 mph) or more
Intake air temperature
-10°C (14°F) or higher

TYPICAL MALFUNCTION THRESHOLDS


Manifold pressure change
Less than 1.75 kPa(gauge) [13.1 mmHg(gauge)]
At engine speed
1050 rpm

CONFIRMATION DRIVING PATTERN


A249360E03

  1. Connect the GTS to the DLC3.
  2. Turn the power switch on (IG).
  3. Turn the GTS on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the power switch off and wait for at least 30 seconds.
  6. Turn the power switch on (IG).
  7. Turn the GTS on.
  8. Put the engine in inspection mode (maintenance mode) (Click here).
  9. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
  10. Accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for at least 10 seconds [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    When accelerating the vehicle, depress the accelerator pedal more than normal to start the engine.

  11. Idle the engine for 30 seconds or more [C].
  12. Accelerate the vehicle to 60 km/h (37 mph) with the shift lever in B [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  13. Perform fuel cut operation for 5 seconds or more, with the accelerator pedal fully released [E].

    HINT:
    When fuel cut is operating "Idle Fuel Cut" in Data List is ON.

  14. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [F].
  15. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  16. Enter the following menus: Power train / Engine and ECT / Utility / All Readiness.
  17. Input the DTC: P0401.
  18. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows NORMAL, the system is normal.
    3. If the DTC judgment result is INCOMPLETE or N/A, perform steps [D] and [E] again.


INSPECTION PROCEDURE

HINT:
  1. By using the Control the EGR Step Position Active Test, the operation of the EGR valve can be checked.
  2. If the EGR valve is normal and is opened using the Active Test, the Data List value changes as follows.

    Data List
    Change in Data List when Number of Steps is Increased Using Control the EGR Step Position Active Test
    MAP
    Pressure rises
  3. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0401)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTC.

    Result 
    Result
    Proceed to
    DTC P0401 is output
    A
    DTC P0401 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0401 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    The A/C switch and all accessory switches should be off and shift lever in P or N.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / MAP and Throttle Idle Position.

  1. Confirm that Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP change in response to EGR step position when Throttle Idle Position is ON in the Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    MAP
    (Data List)
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    1. While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.
    2. Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.



NG
Go to step 4
OK


3.INSPECT EGR VALVE ASSEMBLY
  1. Check if the EGR valve are clogged with deposits.

  1. Check if the EGR valve is closed.

    OK:
    EGR valve is closed and no deposits.


    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 5
A


4.REPLACE EGR VALVE ASSEMBLY
  1. Replace the EGR valve assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).


NEXT


5.CHECK FOR DEPOSIT (INTAKE PORT AND EXHAUST MANIFOLD SUB-ASSEMBLY TO EGR VALVE ASSEMBLY)

A258686

  1. Check for exhaust leaks at each connection point.

  1. Check for cracks, damage, and clogs in the pipes between the intake manifold, the EGR valve assembly and the exhaust manifold sub-assembly.

  1. This check may require the removal of components.

  1. Check if there is a build-up of deposits in the EGR valve of pipes.

    OK:
    No deposits.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the exhaust system (Click here).



NG
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
OK


6.INSPECT EGR COOLER ASSEMBLY
  1. Check for blockage in the EGR cooler assembly.

    OK:
    No blockage.



NG
REPLACE EGR COOLER ASSEMBLY (Click here)
OK


7.READ VALUE USING GTS (MAP)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAP.

  1. Read the MAP value.

    Standard:

    Condition
    GTS Display
    Power switch on (IG)
    80 to 110 kPa(abs) [600 to 825 mmHg(abs)]

    HINT:
    Standard atmospheric pressure is 101 kPa(abs) [758 mmHg(abs)]. For every 100 m (328 ft) increase in altitude, pressure drops by 1 kPa (7.5 mmHg). The pressure also varies due to the weather (high atmospheric pressure, low atmospheric pressure).


Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 10
A


8.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


9.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
  1. Replace the manifold absolute pressure sensor (Click here).


NEXT


10.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

  1. Read the pending DTCs.

    HINT:
    1. If the pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0401.

  1. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit


NEXT

END