Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM

CAN COMMUNICATION SYSTEM > PROBLEM SYMPTOMS TABLE

for Preparation Click here


HINT:
  1. Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  2. Inspect the fuses and relays related to this system before inspecting the suspected areas below.
  3. Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).


Result List of How to Proceed with Troubleshooting 
Symptom
Suspected Area
See page
The result of "How to Proceed with Troubleshooting" is "Open in CAN Main Bus Line".
Open in CAN Main Bus Line (for LHD)
(Includes DLC3 branch lines and terminating resistors)
Click here
Open in CAN Main Bus Line (for RHD)
(Includes DLC3 branch lines and terminating resistors)
Click here
The result of "How to Proceed with Troubleshooting" is "Short in CAN Bus Lines".
Short in CAN Bus Lines (for LHD)
Click here
Short in CAN Bus Lines (for RHD)
Click here
The result of "How to Proceed with Troubleshooting" is "Short to +B in CAN Bus Line".
Short to +B in CAN Bus Line (for LHD)
Click here
Short to +B in CAN Bus Line (for RHD)
Click here
The result of "How to Proceed with Troubleshooting" is "Short to GND in CAN Bus Line".
Short to GND in CAN Bus Line (for LHD)
Click here
Short to GND in CAN Bus Line (for RHD)
Click here
The result of "How to Proceed with Troubleshooting" is "Open in One Side of CAN Branch Line".
Open in One Side of CAN Branch Line
Click here

HINT:
Refer to How to Proceed with Troubleshooting for the V Bus Check procedure.


The suspected communication stop area can be determined based on the ECU or sensor that was not displayed in Communication Bus Check and by referring to the table below.
Communication Stop Mode Table 
Symptom
Suspected Area
See page
"Skid Control (ABS/VSC/TRAC)" is not displayed on the intelligent tester.
Skid Control ECU Communication Stop Mode
Click here
"Power Steering (EPS)" is not displayed on the intelligent tester.
Power Steering ECU Communication Stop Mode
Click here
"Spiral cable (Steering Angle Sensor)" is not displayed on the intelligent tester.
Steering Angle Sensor Communication Stop Mode
Click here
"Power Management1" and/or "Hybrid Vehicle Control" are not displayed on the intelligent tester.
Power Management Control ECU Communication Stop Mode
Click here
"ECM (Engine)" is not displayed on the intelligent tester.
ECM Communication Stop Mode
Click here
"Air Conditioning Amplifier" is not displayed on the intelligent tester.
Air Conditioner Amplifier Communication Stop Mode
Click here
"Main Body" is not displayed on the intelligent tester.
Main Body ECU Communication Stop Mode
Click here
"Clearance Warning (Clearance Sonar2)" is not displayed on the intelligent tester.
Clearance Warning ECU Communication Stop Mode
Click here
"Combination Meter" is not displayed on the intelligent tester.
Combination Meter ECU Communication Stop Mode
Click here
"Certification (Smart)" is not displayed on the intelligent tester.
Certification ECU Communication Stop Mode
Click here
"Airbag" is not displayed on the intelligent tester.
Center Airbag Sensor Communication Stop Mode
Click here
"Display and Navigation (AVN1)" is not displayed on the intelligent tester.
Audio Receiver Assembly Communication Stop Mode
Click here

DTC Combination Table 
Symptom
Suspected Area
See page
Although CAN communication (V bus) is currently normal, ECUs connected to the V bus store CAN communication DTCs.
The probable part for which communication is interrupted can be determined using DTC Combination Table and comparing the DTCs output from ECUs connected to the CAN communication system
Click here